The kinetics of dephosphorization of carbon-saturated iron using an oxidizing slag

The kinetics of dephosphorization of carbon-saturated iron by oxidizing slags were studied at 1330 °C. Nine slag compositions were investigated in the systems CaO-Fe₂O₃-SiO₂-CaF₂ and CaO-Fe₂O₃-SiO₂-CaCl₂. Increasing Fe₂O₃ up to 50 pct was found to increase the rate and extent of dephosphorization, whereas further increases were found to decrease the rate and extent of dephosphorization. This was explained in terms of two competing effects on the driving force, where increased levels of iron oxide increase the oxygen potential for dephosphorization, hence the driving force, but simultaneously dilute the basic components in the slag, lowering the driving force for dephosphorization. CaF₂ and CaCl₂ were found to decrease the rate and extent of dephosphorization at levels higher than 12 pct. The rate of dephosphorization was found to be first order with respect to phosphorous in the metal and was controlled by mass transport in the slag. The oxygen potential at the slag/metal interface was controlled by the FeO activity in the slag. When the kinetic results were analyzed to take account of different driving forces, Fe₂O₃, CaF₂ and CaCl₂ were all found to increase the mass transfer coefficient of phosphorous in the slag, and a quantitative relationship has been demonstrated between these mass transfer coefficients and the slag viscosity for each system studied.     

Fatigue studies of high-palladium dental casting alloys: Part I. Fatigue limits and fracture characteristics*

The fatigue limits and fracture characteristics for a Pd–Cu–Ga alloy and a Pd–Ga alloy were studied. The alloys were cast into tensile test bars with gauge diameter of 3 mm and gauge length of 15 mm, and the surfaces of the castings were neither air-abraded nor polished after removal from the investment. Specimens were prepared from all-new metal (not previously melted), a combination of 50% new metal and 50% old metal (previously melted one time) and 100% old metal. The cast bars were subjected to heat treatment simulating the complete firing cycles for dental porcelain, and fatigued in air at room temperature under uniaxial tension-compression stress at 10 Hz and a ratio of tensile stress amplitude to compressive stress amplitude (R-ratio) of –1. The alloy microstructures and fracture surfaces were examined with a scanning electron microscope (SEM). Results showed that the fatigue limits at 2 x 10⁶cycles of the Pd–Cu–Ga and Pd–Ga alloys were approximately 0.20 and 0.15 of their 0.1% yield strength (YS) in tension, respectively. The fatigue resistance for specimens from both alloys containing 50% old metal and 50% new metal was comparable to that of specimens containing all-new metal, although this decreased dramatically for Pd–Cu–Ga alloy specimens containing all-old metal. The fatigue resistance of the Pd–Cu–Ga alloy subjected to heat treatment simulating the porcelain firing cycles was not adversely affected by remnants of the original as-cast dendritic microstructure that remained in the relatively large test specimens. A longer heat treatment than recommended by the manufacturer for the porcelain firing cycles is needed to completely eliminate the as-cast dendritic structure in these specimens. The Pd–Cu–Ga alloy exhibited superior fatigue resistance to the Pd–Ga alloy, which has an equiaxed-grain microstructure and lower yield strength.     

Bead-based DNA diagnostic assay for chlamydia using nanoparticle-mediated surface-enhanced resonance Raman scattering detection within a lab-on-a-chip format

There is a continued interest in the development of new on-chip protocols for the determination of the causes of infectious disease. In this paper, we demonstrate the use of surface-enhanced resonance Raman scattering (SERRS) for detecting the clinically relevant nucleic acid sequences of Chlamydia trachomatis in a bead-based lab-on-a-chip format, incorporating a solid-phase sample clean-up on-chip. The assay uses streptavidinated polymer microspheres to capture a biotinylated PCR product of the oligonucleotide sequence, which was subsequently hybridized against a complementary rhodamine-labeled, Raman active probe. Central to the assay is an in-channel integrated microfilter, which was used to retain the microspheres, enabling the bound target to be separated from the rest of the sample as part of a solid-phase clean-up (thereby removing any contributions from the background). After washing, the bound Rhodamine labeled detection probe was released thermally from the microspheres by heating and was subsequently mixed on-chip with a stream of silver nanoparticles. The signal was detected downstream using a Raman spectrometer to collect the SERRS response. The assay offers several advantages over traditional laboratory methods, including: the speed of the assay on-chip, the potential for sample clean-up; and the low volume of sample required.     

A Four-Probe dc Method for Measuring the Electrical Resistivities of Molten Metals

A four-probe dc technique for measuring liquid-metal electrical resistivities has been developed, and liquid-resistivity measurements on gallium, tin, lead, copper, a lead tin alloy, a copper tin alloy, and a zinc alloy have been presented. The Lorenz relation has been used to calculate thermal conductivities from these resistivity measurements. The thermal conductivities calculated from these resistivity measurements are (where data are available) in good agreement with recommended liquid-metal thermal conductivities.     

More ‘crop per drop’: constraints and opportunities for precision irrigation in European agriculture

Dwindling water supplies, increasing drought frequency and uncertainties associated with a changing climate mean Europe's irrigated agriculture sector needs to improve water efficiency and produce more 'crop per drop'. This paper summarizes the drivers for change, and the constraints and opportunities for improving agricultural water management through uptake of precision irrigation technologies. A multi‐disciplinary and integrated approach involving irrigation engineers, soil scientists, agronomists and plant physiologists will be needed if the potential for precision irrigation within the field crop sector is to be realized. © 2013 Society of Chemical Industry     

Cryptanalysis of optical security systems with significant output images

The security of the encryption and verification techniques with significant output images is examined by a known-plaintext attack. We introduce an iterative phase-retrieval algorithm based on multiple intensity measurements to heuristically estimate the phase key in the Fourier domain by several plaintext-cyphertext pairs. We obtain correlation output images with very low error by correlating the estimated key with corresponding random phase masks. Our studies show that the convergence behavior of this algorithm sensitively depends on the starting point. We also demonstrate that this algorithm can be used to attack the double random phase encoding technique.     

Reduction Kinetics of Oxidized New Zealand Ironsand Pellets in H2 at Temperatures up to 1443 K

Metallurgical and Materials Transactions B - Direct reduction of iron ore pellets using hydrogen gas has the potential to significantly reduce CO2 emissions from the ironmaking process. In this...