A Digital Deformation Vacuum Gauge with an LC-Generator

The design of a sylphon bellows sensor and the basic circuits of an LC-generator and of a microprocessor unit are presented. An analytical pressure–frequency conversion function and a special method of adjusting the sensor ensure an error of less than 0.05%. The dynamic range is up to 10⁵. The instruments developed cover the ranges 10³, 10⁴, and 10⁵ Pa.     

A 1.5-V 45-mW direct-conversion WCDMA receiver IC in 0.13-/spl mu/m CMOS

A 2-GHz direct-conversion receiver for wide-band code division multiple access (WCDMA) is presented. It includes two low-noise amplifiers (LNAs), an I/Q demodulator, and two sixth-order baseband channel select filters with programmable gain. Quadrature local oscillator (LO) signals are generated on chip in a frequency divider flip-flop. An external interstage filter between the LNAs rejects transmitter leakage to relax demodulator linearity requirements. A low-voltage demodulator topology improves linearity as well as demodulator output pole accuracy. The active-RC baseband filter uses a programmable servo loop for offset compensation and provides an adjacent channel rejection of 39 dB. Programmable gain over 71-dB range in 1-dB steps is merged with the filter to maximize dynamic range. An automatic on-chip frequency calibration scheme provides better than 1.5% corner frequency accuracy. The receiver is integrated in a 0.13-/spl mu/m CMOS process with metal-insulator-metal (MIM) capacitors. Measured receiver performance includes a 6.5-dB noise figure, IIP2 of +27 dBm, and IIP3 of -8.6 dBm. Power consumption is 45 mW.     

Electrochemical synthesis and characterization of chloride doped polyaniline

Chloride doped polyaniline conducting polymer films have been prepared in a protic acid medium (HCl) by potentiodynamic method in an electrochemical cell and studied by cyclic voltammetry and FTIR techniques. The FTIR spectra confirmed Cl^- ion doping in the polymers. The polymerization rate was found to increase with increasing concentration of aniline monomer. But the films obtained at high monomer concentration were rough having a nonuniform flaky polyaniline distribution. Results showed that the polymerization rate did not increase beyond a critical HCl concentration. Cyclic voltammetry suggested that, the oxidation-reduction current increased with an increase in scan rate and that the undoped polyaniline films were not hygroscopic whereas chloride doped polyaniline films were found to be highly hygroscopic.     

The effect of photon energy and temperature on the persistent tunneling photoconductivity effect in Al/δ(Si)-GaAs structures

The phenomenon of persistent tunneling photoconductivity was studied using the tunneling spectroscopy technique at liquid-helium temperature: the separation between the unoccupied levels in a δ-doped layer at the GaAs surface decreased after illumination. This decrease was due to an increase in the width of the quantum well of the δ-doped layer. For photon energies hv exceeding the GaAs band gap E _g , this increase in the width of the quantum well was related to the accumulation of positive charge in the depth of GaAs induced by the generation of the electron-hole pairs and photoionization of deep centers. For hv < E _g (including the case of CO₂ laser), only photoionization is important. The experimental data agree with the self-consistent calculations. The critical temperature for the effect has been determined (T _c = 45 K); at higher temperatures, the effect disappears.     

The radiation resistance of an arbitrarily oriented electric dipole exciting a corner antenna or a plane screen

Rigorous analytic expressions for radiation resistance R _Σ of an electric dipole are obtained for three mutually orthogonal orientations of the dipole’s axis with respect to a plane metal screen or right-angle corner of infinite dimensions. Radiation resistance R _Σ of the dipole oriented arbitrarily in space is calculated and analyzed as a function of the distance from the screen.     

Operation of the dam of the Bureiskaya HPP during filling of the reservoir

Operation of the dam in a transitional mode is described. __________ Translated from Gidrotekhnicheskoe Stroitel’stvo, No. 1, January 2006, pp. 8–15.     

Dominant rock properties affecting the performance of conical picks and the comparison of some experimental and theoretical results

Conical picks are the essential cutting tools used especially on roadheaders, continuous miners and shearers and their cutting performance affects directly the efficiency and the cost of rock/mineral excavation. In this study, in order to better understand the effects of dominant rock properties on cutter performance, 22 different rock specimens having compressive strength values varying from 10 to 170 MPa are first subjected to a wide range of mechanical tests. Then, laboratory full-scale linear cutting tests with different depth of cut and cutter spacing values are realized on large blocks of rock specimens using one type of conical pick. Specific energy, cutting and normal force values for relieved and unrelieved cutting modes are recorded using a triaxial force dynamometer with capacity of 50 tonnes and a data acquisition system. Cutter force and specific energy values are correlated with rock properties and theoretical force and specific energy values obtained from widely used theoretical approaches.The results indicate that uniaxial compressive strength among the rock properties investigated is best correlated with the measured cutter performance values, which is in good agreement with previous studies. However, it is also emphasized in this study that Brazilian tensile strength, Schmidt hammer rebound values, static and dynamic elasticity modulus are also dominant rock properties affecting cutter performance.Theoretical specific energy defined by different researchers has a meaningful relationship with the experimental specific energy, which is an essential parameter for predicting the instantaneous cutting rates of mechanical excavation systems. It is also demonstrated that the experimental cutter forces obtained for 5 mm depth of cut are in good agreement with theoretical force values, if the friction angle between rock and cutting tool is included in the theoretical formulation. It is emphasized that, to some extend, laboratory tests can help to minimize high cost of a trial–error approach in the field.     

Controlled elements for designing ciphers suitable to efficient VLSI implementation

This work considers the problem of increasing the performance of the ciphers based on Data-Dependent (DD) operations (DDO) for VLSI implementations. New minimum size primitives are proposed to design DDOs. Using advanced DDOs instead of DD permutations (DDP) in the DDP-based iterative ciphers Cobra-H64 and Cobra-H128 the number of rounds has been significantly reduced yielding enhancement of the “performance per cost” value and retaining security at the level of indistinguishability from a random transformation. To obtain further enhancement of this parameter a new crypto-scheme based on the advanced DDOs is proposed. The FPGA implementation of the proposed crypto-scheme achieves higher throughput value and minimizes the allocated resources than the conventional designs. Design of the DDO boxes of different orders is considered and their ASIC implementation is estimated.     

Tri-axial sensors and actuators made of a single piezoelectric cylindrical shell

Electromechanical transducers for sensing and actuating disturbances or vibrations have been used in many fields of applications. There have been transducers of different configuration developed for the unidirectional transduction. This paper demonstrates a single element transducer for tri-axial components made of a piezoelectric cylindrical shell. The separation of the tri-axial transductions is achieved by devising a proper electrode arrangement. The structure and the fundamental idea are first presented, and then the numerical analysis by means of the finite element modeling follows, and their characteristics and behaviors are then experimentally verified.     

Ring‐opening polymerization of lactones initiated by diphenylzinc–coinitiator systems

Diphenylzinc, alone or in combination with water and butanone as coinitiators, was used as a polymerization initiator system for a variety of lactones at varying temperatures. The resulting data indicate that the course of the polymerization is greatly influenced by the lactone structure, as well as by the molar ratio of coinitiator to diphenylzinc. When used alone, diphenylzinc exhibited high activity as an initiator in δ‐valerolactone polymerizations, although it was less efficient when used in the β‐butyrolactone and the β‐propiolactone polymerizations. Activity in the polymerization of β‐lactones was increased by adding small amounts of butanone or water. It was also observed that the diphenylzinc–butanone combination was more effective than the diphenylzinc–water mixture in the polymerizations of β‐butyrolactone and β‐propiolactone. Copyright © 2003 Society of Chemical Industry