Structural Changes Induced in Nonstoichiometric Titanium Carbide by High-Temperature Deformation

The microstructure evolution in nonstoichiometric titanium carbide is studied during high-temperature deformation at high strain rates and low strains (shock compression) and at slow strain rates and high strains (superplastic regime). The results demonstrate that high-temperature deformation in a broad range of strain rates offers a means of controlling the microstructure of titanium carbide. By varying deformation conditions, one can obtain materials differing in microstructure and chemical composition, in particular, with equilibrium and nonequilibrium microstructures. Accordingly, the physicochemical properties of such materials also differ.     

On the physical and logical topology design of large-scale optical networks

We consider the problem of designing a network of optical cross-connects (OXCs) to provide end-to-end lightpath services to large numbers of label switched routers (LSRs). We present a set of heuristic algorithms to address the combined problem of physical topology design (i.e., determine the number of OXCs required and the fiber links among them) and logical topology design (i.e., determine the routing and wavelength assignment for the lightpaths among the LSRs). Unlike previous studies which were limited to small topologies with a handful of nodes and a few tens of lightpaths, we have applied our algorithms to networks with hundreds or thousands of LSRs and with a number of lightpaths that is an order of magnitude larger than the number of LSRs. In order to characterize the performance of our algorithms, we have developed lower bounds which can be computed efficiently. We present numerical results for up to 1000 LSRs and for a wide range of system parameters such as the number of wavelengths per fiber, the number of transceivers per LSR, and the number of ports per OXC. The results indicate that it is possible to build large-scale optical networks with rich connectivity in a cost-effective manner, using relatively few but properly dimensioned OXCs.     

An improved statistical analysis of the least mean fourth (LMF) adaptive algorithm

The paper presents an improved statistical analysis of the least mean fourth (LMF) adaptive algorithm behavior for a stationary Gaussian input. The analysis improves previous results in that higher order moments of the weight error vector are not neglected and that it is not restricted to a specific noise distribution. The analysis is based on the independence theory and assumes reasonably slow learning and a large number of adaptive filter coefficients. A new analytical model is derived, which is able to predict the algorithm behavior accurately, both during transient and in steady-state, for small step sizes and long impulse responses. The new model is valid for any zero-mean symmetric noise density function and for any signal-to-noise ratio (SNR). Computer simulations illustrate the accuracy of the new model in predicting the algorithm behavior in several different situations.     

2-D symmetry: theory and filter design applications

In this comprehensive review article, we present the theory of symmetry in two-dimensional (2-D) filter functions and in 2-D Fourier transforms. It is shown that when a filter frequency response possesses symmetry, the realization problem becomes relatively simple. Further, when the frequency response has no symmetry, there is a technique to decompose that frequency response into components each of which has the desired symmetry. This again reduces the complexity of two-dimensional filter design. A number of filter design examples are illustrated.     

Effect of anisotropy of tin on thermomechanical behavior of solder joints

Properties of body centered tetragonal tin are highly anisotropic. As a consequence large stresses can develop at the tin grain boundaries due to coefficient of thermal expansion mismatch during temperature excursions. A modeling approach to evaluate the 3D stress states that develop at grain boundaries during thermomechanical fatigue in tin-based solder is presented. Development of significant amounts of stresses in the plane of the grain boundary can cause grain-boundary sliding and surface-relief effects, while those normal to the grain boundary can cause grain-boundary decohesion and cracking.     

Start-up and steady-state results of a full-scale UASB reactor treating malting wastewater.

An Imhoff tank was reconstructed into a 250 m3 UASB reactor in order to treat a malting plant wastewater. The UASB was inoculated with sludge from an anaerobic lagoon used for slaughterhouse wastewater treatment. After two months of operation the reactor achieved full load with an HRT of 17 h, a COD removal higher than 80% and a biogas production of 300 m3/day (77% average methane content), with an organic loading rate of 3.6 kgCOD/m3.d (0.24 kgCOD/kgVSS.d). A yield coefficient of 0.09 gVSS/gCODrem was found from a mass balance. The fat present in the inoculated sludge (48 mg/gSSV) did not affect the start up performance. Sludge from the inoculum with high content of fat (270 mg/gSSV), was separated by flotation in the first week of operation. The COD removal efficiency was scarcely influenced by the reactor operation temperature (17-25 degrees C).     

The Influence and Interpretation of Surface Parameters for Wetting Transitions in Ternary Mixtures

Starting from a microscopic Hamiltonian defined on a semi-infinite cubic lattice, and employing a mean-field approximation, the surface parameters relevant for wetting in confined ternary mixtures are derived. These are found in terms of the microscopic coupling constants, and yield a physical interpretation of their origins. In comparison with the standard expression for the surface free-energy density, several new terms arising from the derivation are identified. The influence of the surface parameters on a predicted unbinding transition in a mixture of oil, water, and amphiphile demonstrate that existing results are robust to the addition of the extra surface terms.     

Motive Force in a Complex Model of Mass Transfer

Relations for determining a motive force in a complex model of mass transfer as applied to concurrent, countercurrent, and cross motion of the vapor and liquid phases have been introduced. These forces have been compared for different forms of organization of the flow, and their comparison with similar quantities from the known Murphree and Hausen models is presented.     

Interior symmetry and local bifurcation in coupled cell networks

A coupled cell system is a network of dynamical systems, or 'cells', coupled together. Such systems can be represented schematically by a directed graph whose nodes correspond to cells and whose edges represent couplings. A symmetry of a coupled cell system is a permutation of the cells and edges that preserves all internal dynamics and all couplings. It is well known that symmetry can lead to patterns of synchronized cells, rotating waves, multirhythms, and synchronized chaos. Recently, the introduction of a less stringent form of symmetry, the 'symmetry groupoid', has shown that global group-theoretic symmetry is not the only mechanism that can create such states in a coupled cell system. The symmetry groupoid consists of structure-preserving bijections between certain subsets of the cell network, the input sets. Here, we introduce a concept intermediate between the groupoid symmetries and the global group symmetries of a network: 'interior symmetry'. This concept is closely related to the groupoid structure, but imposes stronger constraints of a group-theoretic nature. We develop the local bifurcation theory of coupled cell systems possessing interior symmetries, by analogy with symmetric bifurcation theory. The main results are analogues for 'synchrony-breaking' bifurcations of the Equivariant Branching Lemma for steady-state bifurcation, and the Equivariant Hopf Theorem for bifurcation to time-periodic states.     

Experimental characterisation of the drying effect on uniaxial mechanical behaviour of mortar

The main objective of this present study was to evaluate, for a standard mortar, the drying effect on its mechanical behaviour. Numerous uniaxial compression tests were thus performed with loading-unloading cycles. They were carried out on different samples previously preserved under various conditions of conservation: preserved from desiccation, air drying and rapid drying at 60°C. The obtained results showed significant influences of these conditions on the material behaviour (increase in strength, decrease in Young's modulus and Poisson's ratio) and the necessity of taking into account the coupling effects between mechanical—poromechanical behaviours and drying.