HR-TEM and FIB-SEM characterization of formation of eutectic-like structure from amorphous GdAlO3-Al2O3 system

The crystallization process of the eutectic composition of GdAlO_3-Al_2O_3 from the amorphous phase prepared by rapid-quenching of melt that leads to the formation of a cantaloupe skin-like microstructure was investigated using focused ion-beam scanning electron microscopy (FIB-SEM) and high-resolution transmission electron microscopy (HR-TEM).The amorphous films were heat-treated at temperatures between 1000 °C and 1500 °C for up to 30min to form the eutectic phases of GdAlO_3 and Al_2O_3.The GdAlO_3 and Al_2O_3 crystal phases that formed from the amorphous phase were identified by FIB-SEM and HR-TEM.Both components began to crystallize and grow from the amorphous phase separately at different temperatures.The formation process of these crystal phases was different from that of the ordinary eutectic microstructure solidified from the GdAlO_3-Al_2O_3 system.Therefore,the observed structure is termed eutectic-like for distinction.The microstructures formed from the amorphous phases at sufficiently high temperatures consisted of ultra-fine microstructures of individually crystallized components and were similar to ordinary eutectic microstructures.By heat-treating the amorphous films at 1500 °C for either 2 min,8min or 30min,the ultra-fine components of GdAlO_3 and Al_2O_3 were found to crystallize following a eutectic-like stage after 8min of heat treatment.     

弹性基体磨具的磨抛轨迹与表面加工质量研究

目的 解决以光学玻璃为代表的硬脆材料加工效率与表面质量难以同时得到保证的共性问题。方法 以弹性基体工具磨削抛光技术为基础,分析弹性接触区域内有效工作磨粒的运动行为。基于Preston方程材料去除模型,研究磨抛过程中磨抛接触区域的接触面积、速度分布、多颗磨粒的运动轨迹。基于运动学模型,探究磨抛过程中磨具的运动学参数、磨粒浓度及排布特征等因素对磨粒磨抛轨迹的影响,采用磨具与工件接触区域磨粒运动轨迹相对面积占比和变异系数表征磨粒运动轨迹分布的均匀性,并建立基于轨迹均匀性的加工表面质量评价方法,优化工艺参数。以石英玻璃为加工对象,以硅橡胶中混入金刚石磨粒为基体,通过正交实验研究不同参数对工件表面质量的影响。结果 仿真结果表明,选取自转速度为300 r/min、进给速度为1 mm/s、磨抛进动角为15°,磨粒浓度及排布采用1 mm磨粒理论间距,此时获得的最大磨粒运动轨迹相对面积占比为96.46%,最小变异系数为0.375。通过实验,得到了选取磨抛工艺参数中的最佳参数组合,自转速度为1 200 r/min,进给速度为1 mm/s,磨抛进动角为15°~20°,磨粒浓度及排布采用磨粒间距1 mm,该组合可将工件的表面粗糙度由1.078 μm降至0.057 μm,材料去除率为3.8×10⁸ μm³/min。结论 磨粒运动轨迹的密集程度与自转速度、磨粒浓度及排布呈正相关,与进给速度呈负相关,在考虑加工成本的前提下,采用高自转速度、高磨粒浓度、低进给速度及15°~20°的进动角可以获得密集且均匀的磨粒运动轨迹,提高了工件的表面质量和材料去除效率。     

基于80C196KB的某医用灭菌器控制系统的设计与应用

充分利用80C196KB芯片的片上资源．以其为核心进行外围电路设计．形成一个集信号采集、监测、控制,显示以及打印为一体的小型嵌入式微控制系统,其软件设计全部采用汇编语育．整个控制系统具有简洁明了、灭菌控制可靠．人机界面友好、能够实时监测的特点。     

有限区间内设备顺序预防性维护策略研究

为了克服等周期维护模型忽略设备可靠性要求,以及长期运行期望维护周期模型忽略设备特定阶段维护需求的缺点,通过引入基于役龄递减因子和故障率递增因子的混合式故障率演化规则,建立了有限区间内基于设备可靠性的顺序预防性维护优化模型,并以威布尔分布为例,利用仿真方法对其进行了优化。仿真结果显示,该模型可使设备的维护周期呈递减之势,反映了设备在某一特定阶段的可靠性需求。     

Comparison of three‐dimensional analysis and stereological techniques for quantifying lithium‐ion battery electrode microstructures

Lithium‐ion battery performance is intrinsically linked to electrode microstructure. Quantitative measurement of key structural parameters of lithium‐ion battery electrode microstructures will enable optimization as well as motivate systematic numerical studies for the improvement of battery performance. With the rapid development of 3‐D imaging techniques, quantitative assessment of 3‐D microstructures from 2‐D image sections by stereological methods appears outmoded; however, in spite of the proliferation of tomographic imaging techniques, it remains significantly easier to obtain two‐dimensional (2‐D) data sets. In this study, stereological prediction and three‐dimensional (3‐D) analysis techniques for quantitative assessment of key geometric parameters for characterizing battery electrode microstructures are examined and compared. Lithium‐ion battery electrodes were imaged using synchrotron‐based X‐ray tomographic microscopy. For each electrode sample investigated, stereological analysis was performed on reconstructed 2‐D image sections generated from tomographic imaging, whereas direct 3‐D analysis was performed on reconstructed image volumes. The analysis showed that geometric parameter estimation using 2‐D image sections is bound to be associated with ambiguity and that volume‐based 3‐D characterization of nonconvex, irregular and interconnected particles can be used to more accurately quantify spatially‐dependent parameters, such as tortuosity and pore‐phase connectivity.     

电镀锌钢材表面物理气相沉积Zn-Mg合金镀层的电化学性能(英文)

锌合金镀层由于具有较强的耐腐蚀性能而得到广泛的关注,特别是Zn-Mg合金镀层,其耐腐蚀性能能得到显著提高。采用气相沉积方法制备不同镁含量的Zn-Mg合金镀层,研究Zn-Mg合金镀层中镁含量对其耐腐蚀性能的影响。在3%NaCl溶液中进行浸泡试验、动电位测试和电偶腐蚀试验,研究不同Mg含量镀层的耐腐蚀性能。结果表明,Zn-Mg合金镀层的耐腐蚀性能与Mg含量显著相关,镀层的腐蚀电位随着Mg含量的增加而降低,但是腐蚀电流密度却升高,直至15%Mg含量;在Zn-Mg合金镀层中存在钝化区。     

真空热压铝和铜的固态连接(英文)

在温度623~923K下采用真空热压扩散连接铝和铜,具体工艺为在预置温度下,变形率为0.2mm/min时热压缩10min,再在炉冷过程中,以0.2mm/min成型10min。通过界面分析可以看出,合适的扩散连接温度为823K,在扩散过程中产生了3种主要的金属间化合物层,分别为Al2Cu、AlCu+Al3Cu4和Al4Cu9。3种化合物层的局部硬度分别为(4.97±0.05)、(6.33±0.00)、(6.06±0.18)GPa。     

Electrochemical characteristics of phosphorus doped Si-C composite for anode active material of lithium secondary batteries

Phosphorus doped silicon-carbon composite particles were synthesized through a DC arc plasma torch. Silane(SiH₄) and methane(CH₄) were introduced into the reaction chamber as the precursor of silicon and carbon, respectively. Phosphine(PH₃) was used as a phosphorus dopant gas. Characterization of synthesized particles were carried out by scanning electron microscopy(SEM), X-ray diffractometry(XRD), X-ray photoelectron spectroscopy(XPS) and bulk resistivity measurement. Electrochemical properties were investigated by cyclic test and electrochemical voltage spectroscopy(EVS). In the experimental range, phosphorus doped silicon-carbon composite electrode exhibits enhanced cycle performance than intrinsic silicon and phosphorus doped silicon. It can be explained that incorporation of carbon into silicon acts as a buffer matrix and phosphorus doping plays an important role to enhance the conductivity of the electrode, which leads to the improvement of the cycle performance of the cell.