Dynamic Bending Strains in Planar Trusses with Pinned or Rigid Joints

The method of reverberation ray matrix is applied to analyze the dynamic behavior of structural members in trusses with pinned joints subjected to suddenly applied force. The results are compared with those in planar trusses with rigid joints. Detailed calculations are made with two types of trusses, a small laboratory model made of slender aluminum bars, and a hypothetical real size Pratt truss made of structural steel. It is found that the maximum dynamic bending strains in the members of both types of trusses are very large, comparable with the dynamic axial strains in the same member. The magnitudes of bending strains in the pinned truss differs little from those in the truss with rigid joints for both types of trusses. Such a large dynamic bending strain in a structure member, which is contradictory to the static behavior of the same truss, could be caused by the inertial force of the mass in structural members of the truss.     

Low cycle fatigue and creep behavior of recrystallized Molybdenum near room termperature

The deformation behavior of pure recrystallized molybdenum under cyclic and static loads was investigated in the temperature range between 30°C and 10O°C, for stress amplitudes between 100 MPa and 250 MPa and for static loads up to 200 MPa. The results show that in spite of the low test temperatures and stress levels the Mo material exhibits considerable plastic strains which depend sensitively on frequenez and small changes in temperature.The activation energy deduced for the static and dynamic deformation is less than 0.98 eV which indicates thermally activated processes, to be explained by a dislocation kink model as described in the literature. The low-temperature fatigue behavior appears strongly influenced by creep-fatigue interaction phenomena.     

Observation of atomic steps on CaCO3 crystal surface

By using scanning polarization force microscopy,the deliquescence process and the atomic steps on the cleavage surface of CaCO3 in air were studied in situ.Under an exposure to medium umidity(-57%),the sloiw step movement has been observed.     

Si/SiGe epitaxial-base transistors. I. Materials, physics, andcircuits

A detailed review of SiGe epitaxial base technology is presented, which chronicles the progression of research from materials deposition through device and integration demonstrations, culminating in the first SiGe integrated circuit application. In part I of this paper, the requirements and processes for high-quality SiGe film preparation are discussed, with emphasis on fundamental principles. A detailed overview of SiGe HBT device design and implications for circuit applications is then presented     

Highly compact AC-AC converter achieving a high voltage transferratio

This paper reports a new, highly integrated modular design approach for pulsewidth-modulation AC-AC converters based on a modular phase-bank structure. Novel high-power 3-in-1 integrated bi-directional power modules (IBPM) rated at 1200-V AC and 150 A and the 3-to-1 phase bank circuits have been successfully developed, fabricated and tested. This enables the modularity design of the multiphase converter systems and reduces the critical parasitic inductance. A theoretical analysis of the IBPM's silicon utilization for this new breed of direct power converters has been outlined. A lab prototype at medium power level has been successfully designed, implemented, and tested with good results. A nearly 460-VRMS out voltage at a 1:0.955 voltage transfer ratio, which, perhaps, is the highest performance reported so far in the literature, has been achieved by the novel two-side modulation control system. The converter-fed AC motor system is able to operate over the 0-240 Hz range with inherent regenerative capability and four-quadrant operation. Potential industrial applications are also briefly highlighted in this paper     

含氟聚酰亚胺的辐射交联及其交联度的XPS表征

含氟聚酰亚胺(FPI)是一种耐高温、耐水解的新型聚酰亚胺。到目前为止,尚未见文献报道它的辐射交联。本文发现它能在高温辐射下交联,交联后的含氟聚酰亚胺的玻璃化转变温度以及高温力学性能有明显提高。本文还首次用XPS方法做了它的交联度表征。用XPS方法求得FPI的凝胶化剂量为50Mrad。     

一机多控视频点播系统

介绍一种自行设计、开发的一机多控视频点播系统，讲述了系统组成及设计方案，它具有服务功能多，操作方便、性能价格比高等特点。     

A Petri net based approach to modeling and scheduling for an FMSand a case study

In this paper, a timed-place Petri net (TPPN) model for flexible manufacturing systems (FMSs) is constructed, which contains two major submodels: the stationary transportation model; and the variable process flow model. For multiple automated guided vehicle (AGV) systems, the authors embed a simple rule and introduce a push-AGV strategy in a TPPN model to solve the collision and traffic jam problems of such vehicles. Since a firing sequence of the TPPN from the initial marking to the final marking can be seen as a schedule of the modeled FMS, by using an A^* based search algorithm, namely, the limited-expansion A algorithm, an effective schedule of the part processing can be obtained. To show the promising potential of the proposed work, a prototype FMS is used as a target system for implementation. The experiment results assert that the job-shop scheduling problem can always be satisfactorily solved     

Using thermally stimulated currents to find defective capacitors

BaTiO₃ multilayer capacitors with a nominal capacitance of 3.5nF have been carefully measured using the thermally stimulated current (TSC) technique. When a 300V polarization voltage is applied at room temperature, a new TSC peak appeared in defective sample A after it has been immersed in water. No new peak was found in good-quality sample B after a similar treatment. The accelerated life test shows that sample A hasa much shorter life than sample B in terms of insulation resistance.