Three ways to implement interfacial techniques: application tomeasurements of chromatic dispersion, birefringence, and nonlinearsusceptibilities

Depending on the spectal width of the source illuminating an interferometer, measurement procedures can utilize either the whole interferogram, or only the fringe envelope, or only the fringe quick oscillations. With an ultraband spectrum source, a simplified adaptation of the methods of Fourier transform spectroscopy yields the variations of the test-fiber propagation constant over the whole wavelength-interval of the source. Chromatic dispersion can then be computed from a single interferogram. With narrower spectrum sources, only the fringe envelopes are utilized and yield measurements of mode delay, with application to chromatic and polarization mode dispersion. In this case, however, interferograms at several wavelengths are necessary. With even narrower spectrum sources, the fringe quick oscillations provide measurements of phase shifts, related to changes in the mode propagation constant, when outside perturbations are applied to the test fiber. A direct method for measuring the third-order nonlinear susceptibilities is discussed. In this case the outside perturbation is an intense pump laser field     

“Metallisation” of oxide surfaces observed by in situ high-resolution electron microscopy

Intense irradiation (25–40 A/cm²) at intermediate energy (400 keV) has been found to cause “metallisation” of tungsten oxide and titanium niobate crystal surfaces. The possible mechanisms and the likely consequences for high-resolution imaging of clean oxide surfaces are briefly discussed.     

Comparison of Solutions of the Problems of Elasticity Theory for Different Near-Boundary Elements

We consider three types of near-boundary elements: curvilinear quadrangles and families of arcs and points, and their application to a two-dimensional problem of the static theory of elasticity with boundary conditions in displacements. The comparison of the theoretical and numerical aspects of the obtained solutions is performed. It is shown that the accuracy of evaluation of the components of the vector of displacements increases in the following cases: in the case of complete quantization of the near-boundary region (but not in the case of its partial quantization or quantization with overlapping), in the case where the numbers of arcs and points increase, and in the case of simultaneous application of different types of near-boundary elements (specifically, quadrangles and families of arcs).     

The first accurate measurement of systolic and diastolic bloodpressure

Poiseuille, known for his law of fluid flow, which is the analog of Ohm's law, introduced the units (mmHg) by which we measure blood pressure by using the mercury manometer, which he described in his medical school thesis in 1828. For 50 years, mean blood pressure was all that could be measured because of the long response time of the mercury manometer. It is true that the height of the mercury column displayed pulsatile oscillations, but their amplitude was much less than that of pulse pressure. It is interesting to note that the slowly responding mercury manometer was made to display first systolic then diastolic pressure by means of an ingenious device that contained two oppositely directed check valves. It took from 1828 to 1903 for high-fidelity graphic recordings of blood pressure to appear in which systolic and diastolic pressures were believable. However, systolic and diastolic pressures were measurable since 1878 when Golz and Gaule created their ingenious valved device that permitted use of the slowly responding mercury manometer to display these pressures accurately     

Simulation of magnetic component models in electric circuitsincluding dynamic thermal effects

It is essential in the simulation of power electronics applications to model magnetic components accurately. In addition to modeling the nonlinear hysteresis behavior, eddy currents and winding losses must be included to provide a realistic model. In practice the losses in magnetic components give rise to significant temperature increases which can lead to major changes in the component behavior. In this paper a model of magnetic components is presented which integrates a nonlinear model of hysteresis, electro-magnetic windings and thermal behavior in a single model for use in circuit simulation of power electronics systems. Measurements and simulations are presented which demonstrate the accuracy of the approach for the electrical, magnetic and thermal domains across a variety of operating conditions, including static thermal conditions and dynamic self heating     

高级控制系统提高巴西水电站性能

巴西的一个重要电力公司COPEL最近开发了一个水电站高级控制系统，这是在电力部门经受重大变革时期，提高水电竞争力的里程碑。     

International statements and definitions of the precautionary principle

The precautionary principle (PP), according to one of its definitions, says that lack of certainty, given the current scientific and technological knowledge, shall not delay effective and proportionate actions to prevent hazards, taking into account cost-benefit considerations. Rather than being a single principle, a variety of statements of the PP are found in international treaties and other documents. Apart from any specific legal force of the documents, countries (e.g., France) have used these statements as a starting point for their own guidance documents and regulations for addressing specific environmental and health issues, for example regulation of genetically modified organisms. Thus, any discussion of the precautionary principle must address a complex legal and regulatory situation. We briefly review different statements of the PP and important commentary, largely from the European Union. We provide references to the original source documents (many of which are found in English on the World Wide Web).