“Metallisation” of oxide surfaces observed by in situ high-resolution electron microscopy

Intense irradiation (25–40 A/cm²) at intermediate energy (400 keV) has been found to cause “metallisation” of tungsten oxide and titanium niobate crystal surfaces. The possible mechanisms and the likely consequences for high-resolution imaging of clean oxide surfaces are briefly discussed.     

Incremental transmission loss allocation under pool dispatch

Incremental transmission loss analysis has been used for decades, but recent interest in its application to loss allocation calls for new in-depth results. This paper demonstrates that, for incremental methods to be applied correctly in loss allocation, it is first necessary to specify the load distribution and loss supply strategies. Incremental loss allocation among bus power injections is shown to be arbitrary and, therefore, open to challenge as discriminatory. Loss allocation is possible among incremental loads and/or generators, but the proportion of the total losses assigned to either one is arbitrary. Unique, nonarbitrary incremental loss allocations are however possible among the "equivalent" incremental bilateral exchanges between generators and loads. From these basic components it is possible then to calculate the allocation among generators or loads in any specified proportion. The main results, although developed initially for small increments, are extended to large variations. Finally, a general incremental loss allocation algorithm is developed and tested     

Simulation of magnetic component models in electric circuitsincluding dynamic thermal effects

It is essential in the simulation of power electronics applications to model magnetic components accurately. In addition to modeling the nonlinear hysteresis behavior, eddy currents and winding losses must be included to provide a realistic model. In practice the losses in magnetic components give rise to significant temperature increases which can lead to major changes in the component behavior. In this paper a model of magnetic components is presented which integrates a nonlinear model of hysteresis, electro-magnetic windings and thermal behavior in a single model for use in circuit simulation of power electronics systems. Measurements and simulations are presented which demonstrate the accuracy of the approach for the electrical, magnetic and thermal domains across a variety of operating conditions, including static thermal conditions and dynamic self heating     

Terahertz/optical mixing in symmetric semiconductor quantum wells embedded in optical microcavities

A quantum well (QW) in the simultaneous presence of a terahertz field polarized in the growth direction and an incident optical field near an excitonic resonance results in substantial frequency mixing between the terahertz and optical fields. In particular, a response at new frequencies given by the input optical frequency plus or minus multiples of the terahertz frequency occurs-the terahertz sidebands. In a symmetric QW, the dominant contribution to terahertz-sideband formation is the high-frequency modulation of the overlap integral of the relevant conduction- and valence-subband envelope functions that determine the strength of the interband dipole moment. terahertz-sideband generation is shown to be strongly enhanced in a high quality-factor optical microcavity. Numerical values of the reflected intensity into the first terahertz sideband normalized with respect to the reflected intensity at the fundamental as large as /spl sim/10% are estimated. This suggests that terahertz-sideband generation in semiconductor microcavities is a promising option worthy of exploration for wavelength conversion for wavelength-division multiplexing applications.     

Front Cover

In this paper, the authors present the results of experiments which clearly demonstrate a technical basis confirming that the carrier frequency harmonics data can be used for diagnostics relative to motor stator insulation degradation.     

International statements and definitions of the precautionary principle

The precautionary principle (PP), according to one of its definitions, says that lack of certainty, given the current scientific and technological knowledge, shall not delay effective and proportionate actions to prevent hazards, taking into account cost-benefit considerations. Rather than being a single principle, a variety of statements of the PP are found in international treaties and other documents. Apart from any specific legal force of the documents, countries (e.g., France) have used these statements as a starting point for their own guidance documents and regulations for addressing specific environmental and health issues, for example regulation of genetically modified organisms. Thus, any discussion of the precautionary principle must address a complex legal and regulatory situation. We briefly review different statements of the PP and important commentary, largely from the European Union. We provide references to the original source documents (many of which are found in English on the World Wide Web).     

Homogeneity characterisation of sintered (U,Gd)O2 pellets by X-ray diffraction

(U,Gd)O₂ sintered pellets are fabricated by different methods. The homogeneity characterisation of the Gd content seems to be necessary for a production control to qualify the process and the final product obtained. In this paper, we propose an analysis of the X-ray diffraction powder patterns through the Rietveld method, in which the differences between the experimental and the calculated data proposed from a crystalline structure model are evaluated. This result allows us to determine the cell parameters, that can be correlated with the Gd concentration, and the existence of other phases with different Gd contents.     

Crisis phenomena upon evaporation in grid capillary and porous coatings and arterial structures of heat pipes

The article presents the results of experimental investigations of critical (limit) heat fluxes upon evaporation on porous coatings, and it substantiates the physical model of the process.Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 49, No. 4, pp. 607–614, October, 1985.