INSIGHT VERSUS DESENSITIZATION IN PSYCHOTHERAPY TWO YEARS AFTER TERMINATION.

A TEST BATTERY ASSESSING SPECIFIC AND GENERAL TREATMENT EFFECTS WAS READMINISTERED TO SS PREVIOUSLY ASSESSED BEFORE TREATMENT, AFTER TREATMENT, AND AT A 6-WK FOLLOW-UP FROM GROUPS UNDERGOING INDIVIDUAL PROGRAMS OF (1) MODIFIED SYSTEMATIC DESENSITIZATION, (2) INSIGHT-ORIENTED PSYCHOTHERAPY, (3) ATTENTION-PLACEBO TREATMENT, AND (4) NO TREATMENT. HIGHER RETURN RATES WERE OBTAINED THAN IN ANY PREVIOUS LONG-TERM FOLLOW-UP, REVEALING MAINTAINANCE OF IMPROVEMENT FOUND EARLIER FOR INTERPERSONAL PERFORMANCE ANXIETY. SYSTEMATIC DESENSITIZATION RESULTED IN THE GREATEST SIGNIFICANT IMPROVEMENT (85%), FOLLOWED BY INSIGHT-ORIENTED PSYCHOTHERAPY AND ATTENTION PLACEBO (50% EACH), AND UNTREATED CONTROLS (22%). CHANGES WERE RELIABLE, PREDICTABLE, AND SHOWED EVIDENCE OF FURTHER GENERALIZATION. NO EVIDENCE OF RELAPSE OR SYMPTOM SUBSTITUTION WAS OBTAINED, ALTHOUGH THEY WERE SPECIFICALLY SOUGHT. METHODOLOGICAL PROBLEMS OF FOLLOW-UP STUDIES ARE ALSO DISCUSSED. (36 REF.) (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

OPTICAL ASSESSMENT OF CORN OIL DETERIORATION DURING FRYING

The ultraviolet (UV), visible and near-infrared (NIR) absorption changes in corn oil were measured during processes simulating deep fat frying. Corn oil, maintained at 185C, was exposed to various treatments with nitrogen, air, water injection, air with water injection, and steam. Autoxidation due to a combination of air and high temperature in the simulated frying trials caused visible absorption changes between 400 and 580 nm as the oil deteriorated similar to those observed in potato frying experiments. These absorption changes were found to be associated with changes in an ultraviolet absorption band with a maximum near 270 nm. Second-derivative calibration equations developed at various visible and NIR absorption wavelengths successfully predicted the percentage of total polar materials (%TPM) which accumulated in the corn oil during simulated trials of autoxidation (R values from 0.93 to 0.98). Using spectral data from repetitive potato frying experiments, the predicted %TPM calculated with these equations correlated well with kinematic viscosity measurements (R values from 086 to 0.97).     

Calcium Segregation to a Magnesium Oxide (100) Surface

The segregation of calcium to a (100) cleavage surface of an MgO crystal, with bulk calcium concentration of 200 ppm was measured in situ at T =900° to 1450°C in ultrahigh vacuum, using Auger and low-energy ion-scattering spectroscopies. A measured heat of segregation of approximately -50.3 kJ/mol (-12 kcal/mol) is in favorable agreement with a value of -58.7 kJ/mol (-14 kcal/mol) determined using solute strain energy and surface free energy criteria. The equilibrium value for the calcium segregation between 950° and 1000°C is estimated to correspond to a 20% occupation of the surface cation sites.     

Effects of Oxygen Partial Pressure on the Oxidation of Silicon Carbide

The rate of oxidation of silicon carbide was studied at different partial pressures of oxygen. The diffusion rate constant was found to vary with the logarithm of the partial pressure of oxygen according to the theory of oxidation of thin films as proposed by Engell and Hauffe. An alternative explanation based on the change of free energy with surface coverage was also found to fit the data.     

Stress Relief Mechanisms in Magnesia- and Yttria-Stabilized Zirconia

Stabilized zirconias exhibit pronounced photoelastic effects when viewed with transmitted polarized light. Thin sections reveal stress concentrations around pores and inclusions and at grain boundaries. The yield point of these materials, at some high temperature, is exceeded and plastic deformation tends to relieve these stress concentrations. The microhardness measurements of magnesia-stabilized zirconia indicate both solution hardening and solute segregation and help to explain the physical behavior of this system as the amount of MgO is varied.     

Energy Consumption in Water Blanching

The energy consumption of a tubular water blancher and a water blancher with screw conveyor were measured as a basis for suggesting energy conserving modifications. The former required 0.54 MJ/kg and the latter 0.91 MJ/kg, indicating the importance of complete steam condensation. A pilot scale experiment with a water blancher heated with heat exchange and by steam injection confirmed the energy savings potential of heating with an exchanger to minimize escape of steam rather than by steam injection.