Controlling thickness to tune performance of high-mobility transparent conducting films deposited from Ga-doped ZnO ceramic target

Structure modification has been found to tune significantly the transparent-conducting performance, especially mobility and conductivity of hydrogenated Ga-doped ZnO (HGZO) films. The strong correlation between film thickness and mobility of the films is revealed. The mobility increases quickly with increasing the thickness from 350 to 900 nm, and then tends to be saturated at further thicknesses. A higher mobility than 50 cm²/Vs can be achieved, which is an extra-high value for polycrystalline ZnO films deposited by using the sputtering technique. The thickness-dependent mobility originates from scatterings on grain boundaries and dislocation-induced defects controlled by thin-film growth. Based on the Volmer-Weber model, an expansion model is built up to describe the thickness-dependent crystal growth of the HGZO films, especially at the thick films. As a result, the 800 nm-thick HGZO film obtains the highest performance with high mobility of 51.5 cm²/Vs, low resistivity of 5.3 × 10^?4 Ωcm, and good transmittance of 83.3 %.     

Advanced Surface of Fibrous Activated Carbon Immobilized with FeO/TiO2 for Photocatalytic Evolution of Hydrogen under Visible Light

FeO-doped TiO₂ nanoparticle photocatalysts were immobilized onto the surface of fibrous activated carbon (ACF) via a sol-gel process. As an adsorbent and photocatalyst, FeO-TiO₂ on immobilized ACFs (FeO-TiO₂/ACF) greatly improved the photocatalysis rate of hydrogen production as compared with pure TiO₂ and ACF-TiO₂ under UV irradiation and visible light. The addition of ACFs surface significantly reduced the photogenerated pairs of electrons-hole recombination, thereby promoting the photocatalysis action of doped photo-metal oxides of FeO-TiO₂. Co-doping of FeO onto the lattice of the TiO₂ approach can improve the absorption activity of visible light through photo-metal oxide of TiO₂ and further enhance hydrogen production under visible light. The photocatalytic fabrics (FeO-TiO₂/ACF) were effortlessly split out from the experimental solution for re-utilization and exhibited high stability even after five complete regeneration cycles.     

Bench- and pilot-scale sludge electrodewatering in a diaphragm filter press.

Electrodewatering is a technique in which pressure dewatering is combined with electrokinetic effects to realize an improved solid/liquid separation and hence increased filter cake dry matter contents. In order to be energy efficient, it is shown that sludge should be dewatered by pressure dewatering to a high extent prior to electric field application, and a sufficient contact time for the electric field must be guaranteed. In order to realize these goals, a bench- and pilot-scale diaphragm filter press suited for electrodewatering were constructed for treatment of sewage and other types of sludges. It was shown that electrodewatering of sludge is a feasible technique, especially for biological sludge types. Other types of sludge are less suited for electrodewatering because of the restricted improvements that can be realized in cake dry matter content and the high electric energy consumption. Furthermore, it was shown in pilot-scale tests that the use of a diaphragm filter press with electrodewatering facilities was very well suited to deliver dry filter cakes of sewage sludge at a moderate energy consumption. Depending on local market prices for investment, operating and sludge disposal costs, this technology may therefore lead to important savings in the sludge management process.     

Capture of Organic Vapors Using Adsorption and Electrothermal Regeneration

Activated-carbon-fiber cloth (ACFC) is an alternative adsorbent to granular activated carbon (GAC) for removing and recovering organic vapors from gas streams. Electrothermal desorption (ED) of ACFC provides rapid regeneration while requiring less energy compared to traditional regeneration techniques used with GAC. This paper provides proof-of-concept results from a bench-scale ACFC adsorption system. The automated system captured 1,000 ppmv of hazardous air pollutants/volatile organic compounds (HAPs/VOCs) from air streams and demonstrated the use of ED, using ac voltage, to recover the HAP/VOC as a pure liquid. The desorbed HAP/VOC condensed onto the inner walls of the adsorber and was collected at the bottom of the vessel, without the use of ancillary cooling. Seventy percent of the HAP/VOC was collected per cycle as condensate, with the balance being retained in the regenerated adsorber or recycled to the second adsorber. ED with in-vessel condensation results in minimal N2 consumption and short regeneration cycle times allowing the process to be cost competitive with conventional GAC-based adsorption processes. This technology extends the application of carbon adsorption systems to situations that were previously economically and physically impractical.     

RLS-based initialization for per-tone equalizers in DMT receivers

Per-tone equalization has recently been proposed as an alternative receiver structure for discrete multitone-based systems improving upon the well-known structure based on time-domain equalization. Fast initialization of all the equalizer coefficients has been identified as an open problem. In this letter, a recursive initialization scheme based on recursive least squares with inverse updating is presented for the per-tone equalizers. Simulation results show convergence with an acceptably small number of training symbols. Complexity calculations are made for per-tone equalization and for the case where tones are grouped. It is demonstrated with an example that in the latter case, initialization complexity becomes sufficiently low and comparable to complexity during data transmission.     

Pilot Plant Study of Simultaneous Sewage Sludge Digestion and Metal Leaching

This research is related to a preindustrial pilot scale study of the performance of the simultaneous sewage sludge digestion and metal leaching (SSDML) process for decontamination and stabilization of sewage sludge. Ten batch tests were carried out in two 4?m3 bioreactors under various conditions of operation. Results indicated that the addition of 1.0 to 1.5?g?S0/L, which is the equivalent of approximately 30 to 50?kg?S0 per tons dry sludge, is sufficient to obtain conditions of acidity (pH<2.5) and oxido-reduction potential greater than 500 mV necessary for an effective solubilization of toxic metals. The final average of metal solubilization in the output sludge during the SSDML process varied in the following ranges: 25–78% Cd, 9–32% Cr, 48–100% Cu, 77–99% Mn, 15–53% Ni, 12–47% Pb, and 66–100% Zn. The N, P, and K contents were also preserved in the decontaminated sludge. Moreover, the use of low concentrations of elemental sulfur makes it possible to obtain decontaminated sludge with a low total sulfur content (1.4–1.5% S) compatible with agricultural use. The suspended solids removal calculated for the SSDML process was slightly lower, (2.5±0.4)% volatile suspended solids per day, than those reached using standard aerobic digestion. Finally, the SSDML process was found to be effective in removing bad odors and in the destruction (99–100%) of indicator bacteria.     

Finite element analysis of electromagnetic scattering from a cavity

A finite element method (FEM) is implemented to compute the radar cross section of a two-dimensional (2D) cavity embedded in an infinite ground plane. The method is based on the variational formulation which uses the Fourier transform to couple the fields outside the cavity and those inside the cavity; hence, the scattering problem can be reduced to a bounded domain. The convergence of the discrete finite element problem is analyzed. Numerical results are presented and compared with those obtained by the standard finite element-Green function method and by the 2D integral equation method.