Finite element crack growth algorithm for dynamic fracture

A new finite element crack growth algorithm has been developed to simulate dynamic fracture. In this algorithm, pseudo elements with very high initial density are placed below the crack plane and the density is reduced to zero in a gradual manner as the crack passes the element. A number of linear elastic and elasto-viscoplastic problems have been carried out to test the new algorithm. The results are compared with some of the existing crack growth models.     

The combined effects of curing and environmental exposure on fracture properties of woven carbon/epoxy laminates

This paper concerns a study of the combined effects of curing conditions and environmental exposure on the ultimate properties of two commercial woven carbon/epoxy laminates. Curing parameters (heating rate and applied pressure) were varied so as to obtain six different conditions for each material. Moisture saturation was also achieved by exposing some of the cured samples to environmental conditions of 70°C and 95% relative humidity. Four different tests (tensile, impact, Mode I and Mode II interlaminar fracture resistance) were therefore performed, and the results obtained on the different materials before and after moisture saturation compared. Neither curing pressure nor heating rate nor moisture absorption were observed to have any practical effect on tensile and impact properties. On the contrary, one noticeable effect was the interlaminar fracture resistance of the laminates. The results are discussed and interpreted in terms of damage formation and stress intensification mechanisms.     

Ultrastructural studies of spermiogenesis in rabbit exposed to chronic fluoride toxicity

OBJECTIVE: To compare skinfold thickness measurements with bioelectrical impedance analysis (BIA) as a measure of body fat for use in a survey of children (the National Study of Health and Growth). DESIGN: Part cross-sectional, part repeated measurement study. SETTING: A junior school in Bath. SUBJECTS: 42 boys and 33 girls aged from 9 to 11 years. INTERVENTIONS: Measurements of BIA, height, weight, and triceps, biceps, subscapular and suprailiac skinfolds. RESULTS: All measurements were highly repeatable with intraclass correlation coefficients > 0.90. The level of agreement between estimates of percentage of body fat derived from prediction equations based on impedance or skinfold measurements respectively was poor: the mean difference (impedance estimate minus skinfold estimate) was 4.67% (95% range -3.47 to 12.82) for boys and 7.81% (95% range 1.27 to 14.34) for girls. The two estimates were found to correlate highly (r = 0.83 for boys and r = 0.81 for girls) because weight, used to convert estimates of fat-free mass derived from impedance to fat mass, was highly correlated with impedance and moderately highly correlated with skinfold thicknesses. The correlations of resistance (R) and (H)2/R with skinfold thicknesses were very low. There was a moderate correlation of R and H2/R with log(weight-for-height index), but lower than that of log(weight-for-height index) with each of the skinfolds. CONCLUSIONS: As currently available equations for converting impedance-based estimates of total body water to fat mass are not fully developed for use in children of varying ages, estimates of body fat calculated from skinfold thickness measurements remain preferable in epidemiological studies of children's health and growth.     

Preparation of an anion‐exchange adsorbent by the radiation‐induced grafting of vinylbenzyltrimethylammonium chloride onto cotton cellulose and its application for protein adsorption

Poly(vinylbenzyltrimethylammonium chloride)‐graft‐cotton cellulose, an anion‐exchange matrix, was synthesized by a mutual radiation‐induced grafting technique with a ⁶⁰Co γ‐radiation source. The grafted matrix was characterized by grafting yield estimation, elemental analysis, Fourier transform infrared spectroscopy, and scanning electron microscopy. The grafting yield decreased with the increase in the dose rate. However, the grafting yield and nitrogen content of grafted samples increased almost linearly with an increase in the total irradiation dose. To evaluate the performance of the grafted anion‐exchange matrix, the protein adsorption and elution behavior were investigated in a continuous column process under various experimental conditions, with bovine serum albumin used as a model protein. The binding and elution behavior of the anion‐exchange matrix depended on different experimental parameters, such as the grafting yield, ionic strength, pH of the medium, and amount of protein loaded. From a breakthrough curve, the equilibrium binding capacity and elution percentage of the grafted anion‐exchange matrix were estimated to be 40 mg/g and 94%, respectively. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 5512–5521, 2006     

Short fibre elastomer composites: effect of fibre length,orientation, loading and bonding agent

A series of short fibre reinforced styrene butadiene rubber (SBR) composites were prepared by incorporating sisal fibres of different lengths and different concentrations. The vulcanization behaviour and the properties of the vulcanizates were measured by the relevant ASTM procedures. The processing characteristics such as green strength and mill shrinkage were improved by the addition of fibres. The properties like tensile strength, tear strength, moduli at 10% and 20% elongations were found to be maximum for composites containing longitudinally oriented fibres of length 6 mm. Mixes containing 35 phr loading of fibres and bonding agent showed better mechanical performance than others. The failure behaviour of tensile and tear specimens have been analysed by scanning electron microscopy techniques. Paper presented at the poster session of MRSI AGM VI, Kharagpur, 1995     

Electrosynthesis and impedance studies on zinc selenide

Electrochemical impedance measurements have been used to characterize zinc selenide films prepared by electrochemical co-deposition at a platinum rotating disk electrode. Estimations of capacitance and polarization resistance of variously prepared electrodeposits have been carried out to determine charge carrier density and corrosion rates.     

Design Errors: Inefficiency or Carelessness of Designer?

Design defects are experienced in many projects; the difference is only in the extent of occurrence. This technical note discusses a design error case in a building project in Nepal, where the designer made the wrong assumptions in roof treatment work for waterproofing as well as for heat insulation purposes. From the investigation of the problem, it was found that the waterproofing polymer was not applied directly over concrete slab top. Use of heavy concrete block as a heat insulation material also helped to increase the leakage problem. The problem evoked loss of prestige for project officials, the design consortium, and the contractor.     

Improved accuracy and convergence of discretized population balance for aggregation: The cell average technique

A new discretization method for aggregation equations is developed. It is compared to the fixed pivot technique proposed by Kumar and Ramkrishna (1996a. On the solution of population balance equations by discretization—I. A fixed pivot technique. Chemical Engineering Science 51, 1311-1332). The numerical results for aggregation problems by discretized population balances are consistently overpredicting and diverge before the gelling point in the case of a gelling kernel. The present work establishes a new technique which assigns the particles within the cells more precisely. This is achieved by taking first the average of the newborn particles within the cell and then assigning them to the neighboring nodes such that pre-chosen properties are exactly preserved. The new technique preserves all the advantages of the conventional discretized methods and provides a significant improvement in predicting the particle size distribution (PSD). In addition, it is found that the technique is a powerful tool for the computation of gelling problems. The effectiveness of the technique is illustrated by application to several aggregation problems for suitably selected aggregation kernels including physically relevant kernels.