Ultrasonic Technique for Assessment of the Rim Tightness of Hydro Generator Rotor

At the hydroelectric unit No. 11 of the Nizhnekamsk hydroelectric power plant, the filling wedges of a rotor were investigated by ultrasound in the free st     

Extractive Separation of Oxalic and Nitric Acids Using Tributyl Phosphate

Theoretical Foundations of Chemical Engineering - The extraction of nitric and oxalic acids by neutral compounds TBP, DBBP, and TBPO have been studied. The optimal conditions of their separation...     

Long-term sensor measurements of lung deposited surface area of particulate matter emitted from local vehicular and residential wood combustion sources

Abstract

Lung deposited surface area (LDSA) is a relatively new metric that has been argued to be more accurate at predicting health effects from aerosol exposure. For typical atmospheric aerosol, the LDSA concentration depends mainly on the concentration of ultrafine particles (e.g. vehicular exhaust emissions and residential wood combustion) and therefore optical methods cannot be used to measure and quantify it. The objective of this study was to investigate and describe typical characteristics of LDSA under different urban environments and evaluate how a diffusion charging-based Pegasor AQ Urban sensor (Pegasor Ltd., Finland) can be used as an alternative to optical sensors when assessing local combustion emissions and respective LDSA concentrations. Long-term (12?months) sensor measurements of LDSA were carried out at three distinctly different measurement sites (four sensor nodes) in the Helsinki metropolitan area, Finland. The sites were affected mainly by vehicular exhaust emission (street canyon and urban background stations) and by residential wood combustion (two detached housing area stations). The results showed that the accuracy of the AQ Urban was good (R² = 0.90) for the measurement of LDSA when compared to differential mobility particle sizer. The mean concentrations of LDSA were more than twice as high at the street canyon (mean 22 µm² cm^?3) site when compared to the urban background site (mean 9.4 µm² cm^?3). In the detached housing area, the mean concentrations were 12 µm² cm^?3, and wood combustion typically caused high LDSA peaks in the evenings. High correlations and similar diurnal cycles were observed for the LDSA and black carbon at street canyon and urban background stations. The utilization of a small-scale sensor network (four nodes) showed that the cross-station variability in hourly LDSA concentrations was significant in every site, even within the same detached housing area (distance between the two sites ～670?m).     

Heuristic Solution to the Diffraction Problem on a Superconducting Half-Plane

Journal of Communications Technology and Electronics - Abstract—The article presents a rigorous numerical solution, using the Wiener–Hopf method, to the problem of plane wave...     

Surface Integrity Assessment Upon Electric Discharge Machining of Die Steel Using Non-Destructive Magnetic Barkhausen Noise Technique

Surface integrity characterization of manufactured component is very important as it significantly affects the in-service performance of the component. Till now, surface integrity was evaluated using conventional measurement technique like microhardness tester, X-ray diffraction, optical microscopy and surface roughness tester. But, this technique being laboratory based cannot be used for in-service monitoring of the surface integrity. The present study focuses on the characterization of surface integrity upon electric discharge machined sample using non-destructive magnetic Barkhausen noise technique. Electric discharge machining was performed in die-sinking mode on die steel using copper–tungsten electrode (negative polarity). Experiment was performed by selecting different levels of peak current, gap voltage and pulse on time. Surface integrity characteristics like microhardness change, residual stress, microstructural alteration and surface roughness were analysed using microhardness tester, X-ray diffraction, optical microscopy and surface roughness tester, respectively, and were then correlated with magnetic parameter like root mean square value and peak value obtained from Barkhausen noise signal. The results show a good correlation between magnetic parameter (RMS and Peak value) of Barkhausen noise with the microhardness and surface roughness of the machined sample.

     

Influence of Sodium Microalloying on Rolling Contact Endurance and Mechanical Properties of Hot-Deformed Powder Steels

Russian Journal of Non-Ferrous Metals - Rolling bearing rings comprise a large reserve for expanding powder metallurgy production. This reserve is being incompletely implemented. The hot forging of...     

Anomaly-Based Intrusion Detection System in RPL by Applying Stochastic and Evolutionary Game Models over IoT Environment

Wireless Personal Communications - The rapid development of Information and Communication Technology and the growing number of devices connected to the Internet make the Internet of Things (IoT) as...     

Chlorination of Quartz-Leucoxene Concentrate of Yarega Field

Metallurgical and Materials Transactions B - The process of obtaining titanium tetrachloride (TiCl4) from the quartz-leucoxene concentrate (QLC) from the Yaregskoe oil-titanium field was studied....     

A study on harvesting of PKL electricity

The efficiency of any electric cell or battery is very important. To keep it in mind it has been studied the columbic efficiency, voltaic efficiency and energy efficiency of a PKL (Pathor Kuchi Leaf) Quasi Voltaic Cell or Modified Voltaic Cell. It was found that the columbic efficiency data illustrated that this efficiency was lower comparing to other efficiencies may be the absence of salt bridge or separator between the electrodes. Because, our designed and fabricated PKL cell does not have any salt bridge. So that the internal resistance is lower than the traditional voltaic cell and as a result more current was found. The voltage and current changes with time and I–V characteristics for PKL unit cell, module, panel and array have also been studied. It is shown that the voltaic and energy efficiency have been studied. However, the highest efficiency was obtained for 40% PKL sap with 5% secondary salt in 55% aqueous solution, which implies that the concentration of PKL juice can play an important role regarding efficiency. It was also found that the average energy efficiency was 97.43% and it was also found that the average voltaic efficiency was 57.29%. Finally, morphological study FESEM (Field Emission Scanning Electron Microscopy) has also been performed. It is seen that the results confirmed that Zn was deposited on the Cu surface during the electro deposition process in PKL solution. Using AAS, it has been measured the concentration of [Cu²⁺] as a reactant ion and the concentration of [Zn²⁺] as a product ion those have been tabulated and graphically discussed. The variation of pH has also been studied with time and which was also tabulated and graphically discussed.