Experiments of a prototype wind-driven reverse osmosis desalination system with feedback control

A prototype wind-powered reverse osmosis desalination system was constructed and tested on Coconut Island off the northern coast of Oahu, Hawaii, for brackish water desalination. The system has four major subsystems: a multi-vaned windmill/pump, a flow/pressure stabilizer, a reverse osmosis module, and a control mechanism. The feedback control mechanism, developed by this study, allowed this prototype system to be operated satisfactorily under mild ambient wind of 5 m/s or less. No auxiliary power source was needed. The system operational data showed that at an average wind speed of 5 m/s, brackish feedwater at a total dissolved solids concentration of 3000 mg/1 and at a flow rate of 13 1/min could be processed by this system. The average rejection rate of this prototype system was 97% and the average recovery ratio was 20%. The energy efficiency of the system was measured at 3 5%, which is comparable to the typical energy efficiency of well-operated multi-vaned windmills. Generally, the system's energy efficiency decreases as wind speed increases.     

Dissipative structures of autocatalytic reactions in tubular flow reactors

Dissipative structures of autocatalytic reactions with initially uniform concentrations are studied in tubular flow reactors. A unique steady state exists in a continuous stirred tank reactor. Linear stability analysis predicts either a stable node, a focus or an unstable saddle-focus. Sustained oscillations around the unstable focus can occur for high values of Damköhler number. In distributed parameter systems, travelling, standing or complex oscillatory waves are detected. For low values of Damköhler number, travelling waves with pseudo-constant patterns are observed. With intermediate values of Damköhler number, single or multiple standing waves are obtained. The temporal behavior indicates also the appearance of retriggering or echo waves. For high values of Damköhler number, both single peak and complex multipeak oscillations are found. In the cell model, both regular oscillations near the inlet and chaotic behavior downstream are observed. In the dispersion model, higher Peclet numbers eliminate the oscillations. The spatial profile shows a train of pulsating waves for the discret model and a single pulsating or solitary wave for the continuous model.     

Fluidized bed combustion of high ash anthracite: Analysis of combustion efficiency and particle size distribution

Fluidized bed combustion of high ash anthracite (HAA) was experimentally studied. The combustor consists of 0.25 m ID bed, and auxiliary equipments for coal feeding, ash removal, lemperature control, etc. Experimental results elucidate main cause of fuel loss to be elutriation of fines (i.e., flyash) containing unburned carbon. However, detailed balances of particle size distribution show majority of carbon in flyash comes from fines contained in the feed instead of attrition of coarse particles. The latter is the main source of flyash for conventional coal. The difference is due to much smaller attrition rate of HAA; feed HAA particles do not shrink much in size by combustion and attrition.     

Effect of surface coating on the screw loosening of dental abutment screws

Regardless of the type of performed restoration, in most cases, a screw connection is employed between the abutment and implant. For this reason, implant screw loosening has remained a problem in restorative practices. The purpose of this study was to compare the surface of coated/plated screws with titanium and gold alloy screws and to evaluate the physical properties of coated/plated material after scratch tests via FE-SEM (field emission scanning electron microscopy) investigation. GoldTite, titanium screws provided by 3i (Implant Innovation, USA) and TorqTite, titanium screws by Steri-Oss (Nobel Biocare, USA) and gold screws and titanium screws by AVANA (Osstem Implant, Korea) were selected for this study. The surface, crest, and root of the abutment screws were observed by FE-SEM. A micro-diamond needle was also prepared for the scratch test. Each abutment screw was fixed, and a scratch on the surface of the head region was made at constant load and thereafter the fine trace was observed with FE-SEM. The surface of GoldTite was smoother than that of other screws and it also had abundant ductility and malleability compared with titanium and gold screws. The scratch tests also revealed that teflon particles were exfoliated easily in the screw coated with teflon. The titanium screw had rough surface and low ductility. The clinical use of gold-plated screws is recommended as a means of preventing screw loosening.     

Polar-Cartesian Hybrid Transforms: A novel 2D range scan registration algorithm

Registration of range scans is commonly required in many localization and mapping algorithms. In this paper, we introduce a novel approach called Polar-Cartesian Hybrid Transforms for pair-wise registration of range scans. The proposed algorithm iteratively establishes correspondences by searching the points with closest polar angles in the polar coordinate frame. An angular look-up table is constructed based on the properties of the laser range finder to accelerate the searching procedure. In order to speed up the convergence, we compute the difference of polar range of every matched point pair to select the most contributing correspondences. After the correspondences are determined, the transformation is computed in Cartesian coordinate frame using a point-to-line metric. Combining the advantages of the polar and Cartesian coordinate frames, both robustness and efficiency are greatly improved compared with an up-to-date ICP algorithm.     

Direct microscale imprinting of Al at room temperature with Si inserts

For direct imprinting of metals, hard materials such as diamond and SiC have been used to construct mold inserts in preference to Si, despite the ease in fabricating Si-based micro-/nano- scale structures. In this communication, we demonstrate that micron scale Al structures can be replicated with good fidelity at room temperature by compression molding with Si inserts without incurring insert damage. We further report on results of a finite element analysis of the mechanics of the molding process. The finite element results provide some understanding of the observed lack of damage to the Si inserts.     

Reducing control points in lofted B-spline surface interpolation using common knot vector determination

A new algorithm for reducing control points in lofted surface interpolation to rows of data points is presented in this paper. The key step of surface lofting is to obtain a set of compatible B-spline curves interpolating each row. Given a set of points and their parameterization, a necessary and sufficient condition is proposed to determine the existence of interpolating B-spline curves defined on a given knot vector. Based on this condition, we first properly construct a common knot vector that guarantees the existence of interpolating B-spline curves to each row of points. Then we calculate a set of interpolating B-spline curves defined on the common knot vector by energy minimization. Using this method, fewer control points are employed while maintaining a visually pleasing shape of the lofted surface. Several experimental results demonstrate the usability and quality of the proposed method.     

Pitchfork bifurcation and flip-flop operation with a coupled nonlinear system

A ring cavity system consisting of two hybrid Michelson interferometers coupled together with feedback is constructed. This system shows spatial bifurcation and can be utilized as an all-optical flip-flop device. We demonstrate experimentally a flip-flop operation by use of only a positive pulse in this system.