新的载体媒介传递膜

总结了近几年研究和发展的几种载体媒介传递膜。与支撑液膜相比，这些膜具有好的稳定性和长的寿命。对某些物质，如重金属离子、小分子中性碳氢化合物、氨基酸等有高的选择性和通量。它们的传递机理为固定位置跳跃或移动和固定载体2种机理结合。这些研究有望在环境、生物等技术领域中应用。     

Chemical compositions and optical properties of HfOxNy thin films at different substrate temperatures

High-k HfO_xN_y thin films have been grown by radio frequency (rf) reactive sputtering of metal Hf target in N₂/Ar/O₂ ambient at different substrate temperatures. The chemical compositions of the films have been investigated as a function of substrate temperature by X-ray photoelectron spectroscopy (XPS). XPS measurements showed that nitrogen concentration increases with an increase in substrate temperature. Room-temperature spectroscopic ellipsometry (SE) with photon energy 0.75–6.5 eV was used to investigate the optical properties of the films. SE results demonstrated that refractive index n increases with an increase in substrate temperature. Based on TL parameters which were obtained from the best fit results used in a simulation of the measured spectra, meanwhile, we conclude that the energy band gap (E_g) decreases with an increase in substrate temperature.     

Intermittent Phenomena in Switched Systems With High Coupling Strengths

In this paper, one kind of intermittency generated by a discontinuous system is studied. Although this system, which is composed of two switched subsystems coupled with a high strength, is nonsmooth, the mechanism of this kind of intermittency can be analyzed with several explicit relations between the intermittency characteristics and the system control parameters. In particular, estimates of "steady-state" values of the system (in the laminar phases) and a critical value for this intermittency can be derived, which are helpful in relevant control systems design. Moreover, some power laws for the observed intermittency are obtained and discussed     

引子渡水电站大坝施工质量控制及成果简析

混凝土面板堆石坝是引子渡水电站的主要水工建筑物,在大坝坝体填筑及混凝土面板的施工过程中,通过室内及现场试验确定了质量控制参数,并采取了必要的质量控制措施,从而保证了工程质量。本文主要对质量控制情况及检测成果作简要介绍。     

直接纺大批量POY260dtex/144f生产工艺探讨

研究了熔体直接纺长丝装置大批量生产差别化纤维 2 60dtex/14 4fPOY品种的工艺 ,并且对影响POY质量的因素进行了探讨     

Elastic solutions of a cylindrical rod containing periodically distributed inclusions with axisymmetric eigenstrains

Summary. In this paper, we give the elastic solution for a special type of microstructure – a circular cylindrical rod containing periodically distributed inclusions along its axial direction. Each inclusion has the same uniform axisymmetric transformation strain (eigenstrain). Analytical elastic solutions are obtained for the displacements, stresses and elastic strain energy of the rod. The effects of microstructure and its evolution (growth of inclusions) on the elastic stress and strain fields as well as the strain energy of the rod are quantitatively demonstrated. As a result of such microstructure evolution nominal stress-strain relation with strain softening is derived for a rod under uniaxial tension.     

Programmable group-delay module using binary polarization switching

We demonstrate the first programmable group-delay module based on polarization switching. With a unique binary tuning mechanism, the device can generate any differential group delay value from -45 to +45 ps with a resolution of 1.40 ps, or any true-time-delay value from 0 to 45 ps with a resolution of 0.7 ps. The delay varying speeds for both applications are under 1 ms and can be as fast as 0.1 ms. We evaluate both the dynamic and static performances of the device while paying special attention to its dynamic figures of merit for polarization-mode dispersion emulation and compensation applications. Our experiment shows that the device exhibits a negligible transient-effect induced power penalty (<0.2 dB) in a 10-Gb/s nonreturn-to-zero system.     

Effect of heat treatments on tensile properties and microstructures of wrought Mg−Zn−Zr-RE alloys

The effect of heat treatments on the tensile properties and microstructures of wrought Mg–Zn–Zr-Rare earth alloys MB25 and MB26 have been studied in this paper. It was shown that the homogenization of the cast ingots decreased the strength of the extruded bars because some grain boundary phases were dissolved during the process of this treatment, while the ageing treatment of the extruded bars increased the strength due to the dispersive precipitation of MgZn₂ phase. The quenching + ageing treatments of the extruded bars decreases the strength and plasticity because of the growing up of the grains.Abbreviations ED electron diffraction - GB grain boundary - RE rare earth - TEM transmission electron microscope     

Large-scale quantum mechanical simulations of high- Z metals

High-Z metals constitute a particular challenge for large-scale ab initio electronic-structure calculations, as they require high resolution due to the presence of strongly localized states and require many eigenstates to be computed due to the large number of electrons and need to accurately resolve the Fermi surface. Here, we report recent findings on high-Z metals, using an efficient massively parallel planewave implementation on some of the largest computational architectures currently available. We discuss the particular architectures employed and methodological advances required to harness them effectively. We present a pair-correlation function for U, calculated using quantum molecular dynamics, and discuss relaxations of Pu atoms in the vicinity of defects in aged and alloyed Pu. We find that the self-irradiation associated with aging has a negligible effect on the compressibility of Pu relative to other factors such as alloying. The US Goverment’s right to retain a non-exclusive, royalty-free license in and to any copyright is acknowledged.     

First-principles study of the tensile and fracture of the Al/TiN interface

Employing the density functional theory, we investigate the tensile and fracture processes of the Al/TiN(0 0 1) interface. The simulation presents directly the strain–stress relationship, the ideal tensile strength and the process of bond breaking of the system. Through the analysis of deformation, we find that the softer Al layers deform larger than the harder TiN layers during the tensile process. And fracture occurs between the interface and the sub-interface Al layers. In addition, the results show that during the tensile process, the ripple of the interfacial TiN layer decreases gradually with the increment of the strain. Charge transfer was detected from the Al to TiN layers near the interface area during the tensile process by means of charge density and density of states analyses. The charge transfer affects the fracture process. Compared to our previous study of the Al/TiN(1 1 1) interface, the Al/TiN(0 0 1) interface has smaller work of adhesion and larger tensile strength than the Al/TiN(1 1 1) interface. Our investigation shows that the fractures of the Al/TiN(0 0 1) and (1 1 1) interface systems both happen in the Al layers near the interface.