Optical-transmission characteristics of optical-fiber cables and installed optical-fiber cable networks for WDM systems

Many cables containing 1.3-/spl mu/m zero-dispersion single-mode (SM) optical fibers are installed in trunk and access networks. Recently, there have been a number of studies on wavelength-division-multiplexing (WDM) systems designed to increase transmission capacity and flexibility. If we can construct WDM systems using SM optical-fiber cable networks designed to transmit using wavelengths in the 1.3-/spl mu/m window (O-band), this will prove very effective in reducing construction costs. It is therefore important to examine the wavelength dependence of the transmission characteristics of SM optical-fiber cables and networks that have already been installed and in which several optical fibers are joined. In this paper, we describe the measured optical characteristics of SM optical-fiber cables and installed optical-fiber cable networks at various wavelengths. The optical characteristics were stable in the 1.46 to 1.625-/spl mu/m wavelength range and we confirmed that the installed SM optical-fiber cable networks could be used for WDM system applications.     

Microscale Patterning of Mesoscopic PZN-PT Single Crystal Films by Crystal ion Slicing and Laser-Induced Etching

Advances in the fabrication of solid-solution single crystal relaxor ferroelectrics have made it possible to produce highly efficient piezoelectric crystals, and have attracted renewed interest in the use of these crystals for a new generation of piezoelectric transducers, actuators and sensors. Of particular interest is their incorporation into micro-electromechanical systems (MEMS). In this paper we report on the laser-induced wet chemical etching of lead zinc niobate-lead titanate (PZN-PT) in hydrochloric acid (HCl). Argon-ion laser radiation at power levels up to 4 W is focused to a spot diameter of about 15μm and results in the chemical etching of grooves at patterning speeds up to 5μm/sec. Crystal ion slicing, an ion-implant-based film separation technique, is used in combination with laser etching to form 5 to 10μm-thick patterned and freestanding films for incorporation into micro-electromechanical devices.     

Evaluation of the Properties of Si3N4/Si3N4 Joint Brazed Using a Filler Alloy Containing Pd

Si3N4 ceramic was jointed to itself using a filler alloy of Cu76.5Pd8.5Ti15, and the mechanical properties of the jointwere measured and analyzed. By using a filler alloy of Cu76.5Pd8.5Ti15, the SisN4/SisN4 joints were obtained bybrazing at 1373～1473 K f     

Velocity selective filters recursively implemented in the spatiotemporal domain.

Energy-based methods for motion estimation in image sequences process the input data either in the spatiotemporal or in the frequency domain. In both cases, the algorithms already described in the literature often require a huge number of elementary operations. In this paper, we describe a class of velocity selective filters which yield an accurate detection of the edges moving in the sequence. We first present a filtering scheme based on a convolution operation computed on a finite size neighborhood and describe its properties in the spatiotemporal and frequency domains. Then, we show that filters with similar properties can be implemented recursively, i.e., as convolutions computed on infinite-size neighborhoods. As an example, we finally show the filters' responses in the case of two superimposed translational motions.     

Using the magneto-optical Kerr effect to study magnetization processes in two-dimensional magnonic crystals based on YIG thin films

The magneto-optical Kerr effect for red (628 nm) and green (532 nm) light is used to study magnetization processes in 2D magnonic crystals obtained by etching pits with the diameter D ≈ 32 μm to a depth of t ≤ 2 μm in a 16.1-μm-thick film of yttrium iron garnet (YIG). Hysteresis loops obtained in the case of the inplane crystal magnetization at 628 nm are characterized by lower saturation fields H _s and higher remanent magnetizations than those obtained at 532 nm, a result that is attributed to different absorption coefficients of the YIG film at these wavelengths. This difference between the magnetization curves reflects the fact that the magnonic-crystal surface probed with the green light makes a greater contribution to the magneto-optical Kerr effect. Therefore, the green light is more sensitive to the demagnetizing fields, which govern magnetization processes in the magnonic crystals.     

1/f noise in large-area Hg<Subscript>1−x</Subscript>Cd<Subscript>x</Subscript>Te photodiodes

The 1/f noise in photovoltaic (PV) molecular-beam epitaxy (MBE)-grown Hg_1−xCd_xTe double-layer planar heterostructure (DLPH) large-area detectors is a critical noise component with the potential to limit sensitivity of the cross-track infrared sounder (CrIS) instrument. Therefore, an understanding of the origins and mechanisms of noise currents in these PV detectors is of great importance. Excess low-frequency noise has been measured on a number of 1000-μm-diameter active-area detectors of varying “quality” (i.e., having a wide range of I-V characteristics at 78 K). The 1/f noise was measured as a function of cut-off wavelength under illuminated conditions. For short-wave infrared (SWIR) detectors at 98 K, minimal 1/f noise was measured when the total current was dominated by diffusion with white noise spectral density in the mid-10⁻¹⁵A/Hz^1/2 range. For SWIR detectors dominated by other than diffusion current, the ratio, α, of the noise current in unit bandwidth i_n(f = 1 Hz, V_d = −60 mV, and Δf = 1 Hz) to dark current I_d(V_d = −60 mV) was α_SW-d = i_n/I_d ∼ 1 × 10⁻³. The SWIR detectors measured at 0 mV under illuminated conditions had median α_SW-P = i_n/I_ph ∼ 7 × 10⁻⁶. For mid-wave infrared (MWIR) detectors, α_MW-d = i_n/I_d ∼ 2 × 10⁻⁴, due to tunneling current contributions to the 1/f noise. Measurements on forty-nine 1000-μm-diameter MWIR detectors under illuminated conditions at 98 K and −60 mV bias resulted in α_MW-P = i_n/I_ph = 4.16 ± 1.69 × 10⁻⁶. A significant point to note is that the photo-induced noise spectra are nearly identical at 0 mV and 100 mV reverse bias, with a noise-current-to-photocurrent ratio, α_MW-P, in the mid 10⁻⁶ range. For long-wave infrared (LWIR) detectors measured at 78 K, the ratio, α_LW-d = i_n/I_d ∼ 6 × 10⁻⁶, for the best performers. The majority of the LWIR detectors exhibited α_LW-d on the order of 2 × 10⁻⁵. The photo-induced 1/f noise had α_LW-P = i_n/I_ph ∼ 5 × 10⁻⁶. The value of the noise-current-to-dark-current ratio, α appears to increase with increasing bandgap. It is not clear if this is due to different current mechanisms impacting 1/f noise performance. Measurements on detectors of different bandgaps are needed at temperatures where diffusion current is the dominant current. Excess low-frequency noise measurements made as a function of detector reverse bias indicate 1/f noise may result primarily from the dominant current mechanism at each particular bias. The 1/f noise was not a direct function of the applied bias.     

Training and optimization of an artificial neural network controlling a hybrid power filter

A hybrid power compensator (HPC) consisting of a static VAr compensator and a dynamic compensator needs to be optimally controlled during the compensation of nonlinear loads. The HPC must be controlled to meet minimum requirements in terms of power factor and harmonic distortion, while at the same time minimizing its total cost. An artificial neural network (ANN) is used to control the HPC amidst a very dynamic power system environment. The performance of a reference ANN is evaluated while controlling an HPC connected to a typical nonlinear industrial load. The training and performance of the ANN is then optimized in terms of training set size, training set packing and ANN topology and the performance compared to the reference ANN. This paper highlights the importance of optimising the mentioned ANN parameters to achieve optimum ANN training and modeling accuracy. The results obtained reveals that the application of an ANN in controlling an HPC is feasible given that the ANN parameters are chosen appropriately.     

Analytic models for the latency and steady-state throughput of TCP Tahoe, Reno, and SACK

Continuing the process of improvements made to TCP through the addition of new algorithms in Tahoe and Reno, TCP SACK aims to provide robustness to TCP in the presence of multiple losses from the same window. In this paper we present analytic models to estimate the latency and steady-state throughput of TCP Tahoe, Reno, and SACK and validate our models using both simulations and TCP traces collected from the Internet. In addition to being the first models for the latency of finite Tahoe and SACK flows, our model for the latency of TCP Reno gives a more accurate estimation of the transfer times than existing models. The improved accuracy is partly due to a more accurate modeling of the timeouts, evolution of cwnd during slow start and the delayed ACK timer. Our models also show that, under the losses introduced by the droptail queues which dominate most routers in the Internet, current implementations of SACK can fail to provide adequate protection against timeouts and a loss of roughly more than half the packets in a round will lead to timeouts. We also show that with independent losses SACK performs better than Tahoe and Reno and, as losses become correlated, Tahoe can outperform both Reno and SACK.     

Synthesis of ZSM‐5 Films and Monoliths with Bimodal Micro/Mesoscopic Structures

A route to synthesize ZSM‐5 crystals with a bimodal micro/mesoscopic pore system has been developed in this study; the successful incorporation of the mesopores within the ZSM‐5 structure was performed using tetrapropylammonium hydroxide (TPAOH)‐impregnated mesoporous materials containing carbon nanotubes in the pores, which were encapsulated in the ZSM‐5 crystals during a solid rearrangement process within the framework. Such mesoporous ZSM‐5 zeolites can be readily obtained as powders, thin films, or monoliths.     

QR factoring to compute the GCD of univariate approximate polynomials

We present a stable and practical algorithm that uses QR factors of the Sylvester matrix to compute the greatest common divisor (GCD) of univariate approximate polynomials over /spl Ropf/[x] or /spl Copf/[x]. An approximate polynomial is a polynomial with coefficients that are not known with certainty. The algorithm of this paper improves over previously published algorithms by handling the case when common roots are near to or outside the unit circle, by splitting and reversal if necessary. The algorithm has been tested on thousands of examples, including pairs of polynomials of up to degree 1000, and is now distributed as the program QRGCD in the SNAP package of Maple 9.