Highly Exposed ?NH2 Edge on Fragmented g-C3N4 Framework with Integrated Molybdenum Atoms for Catalytic CO2 Cycloaddition: DFT and Techno-Economic Assessment

This study focuses on the applicability of single-atom Mo-doped graphitic carbon nitride (GCN) nanosheets which are specifically engineered with high surface area (exfoliated GCN),  NH₂ rich edges, and maximum utilization of isolated atomic Mo for propylene carbonate (PC) production through CO₂ cycloaddition of propylene oxide (PO). Various operational parameters are optimized, for example, temperature (130 °C), pressure (20 bar), catalyst (Mo₂GCN), and catalyst mass (0.1 g). Under optimal conditions, 2% Mo-doped GCN (Mo₂GCN) has the highest catalytic performance, especially the turnover frequency (TOF) obtained, 36.4 h⁻¹ is higher than most reported studies. DFT simulations prove the catalytic performance of Mo₂GCN significantly decreases the activation energy barrier for PO ring-opening from 50–60 to 4.903 kcal mol⁻¹. Coexistence of Lewis acid/base group improves the CO₂ cycloaddition performance by the formation of coordination bond between electron-deficient Mo atom with O atom of PO, while  NH₂ surface group disrupts the stability of CO₂ bond by donating electrons into its low-level empty orbital. Steady-state process simulation of the industrial-scale consumes 4.4 ton h⁻¹ of CO₂ with PC production of 10.2 ton h⁻¹. Techno-economic assessment profit from Mo₂GCN is estimated to be 60.39 million USD year⁻¹ at a catalyst loss rate of 0.01 wt% h⁻¹.     

Microalgae-Based Biohybrid Microrobot for Accelerated Diabetic Wound Healing

A variety of wound healing platforms have been proposed to alleviate the hypoxic condition and/or to modulate the immune responses for the treatment of chronic wounds in diabetes. However, these platforms with the passive diffusion of therapeutic agents through the blood clot result in the relatively low delivery efficiency into the deep wound site. Here, a microalgae-based biohybrid microrobot for accelerated diabetic wound healing is developed. The biohybrid microrobot autonomously moves at velocity of 33.3 µm s⁻¹ and generates oxygen for the alleviation of hypoxic condition. In addition, the microrobot efficiently bound with inflammatory chemokines of interleukin-8 (IL-8) and monocyte chemoattractant protein-1 (MCP-1) for modulating the immune responses. The enhanced penetration of microrobot is corroborated by measuring fibrin clots in biomimetic wound using microfluidic devices and the enhanced retention of microrobot is confirmed in the real wounded mouse skin tissue. After deposition on the chronic wound in diabetic mice without wound dressing, the wounds treated with microrobots are completely healed after 9 days with the significant decrease of inflammatory cytokines below 31% of the control level and the upregulated angiogenesis above 20 times of CD31⁺ cells. These results confirm the feasibility of microrobots as a next-generation platform for diabetic wound healing.     

Regulation of Polymer Configurations Enables Green Solvent-Processed Large-Area Binary All-Polymer Solar Cells With Breakthrough Performance and High Efficiency Stretchability Factor

With the great potential of the all-polymer solar cells for large-area wearable devices, both large-area device efficiency and mechanical flexibility are very critical but attract limited attention. In this work, from the perspective of the polymer configurations, two types of terpolymer acceptors PYTX-A and PYTX-B (X = Cl or H) are developed. The configuration difference caused by the replacement of non-conjugated units results in distinct photovoltaic performance and mechanical flexibility. Benefiting from a good match between the intrinsically slow film-forming of the active materials and the technically slow film-forming of the blade-coating process, the toluene-processed large-area (1.21 cm²) binary device achieves a record efficiency of 14.70%. More importantly, a new parameter of efficiency stretchability factor (ESF) is proposed for the first time to comprehensively evaluate the overall device performance. PM6:PYTCl-A and PM6:PYTCl-B yield significantly higher ESF than PM6:PY-IT. Further blending with non-conjugated polymer donor PM6-A, the best ESF of 3.12% is achieved for PM6-A:PYTCl-A, which is among the highest comprehensive performances.     

Duplex spinel-ZrO2 ceramics

Duplex spinel-ZrO₂ ceramic composites were produced by an emulsion-hot kerosene drying technique. The sintered duplex spinel-ZrO₂ ceramics which had the composition of 55 wt% Al₂O₃-20 wt% ZrO₂-25 wt% MgO, consisted of a spinel matrix, whose grain size was in the range of 1.5 to 2.0 m, and uniformly dispersed zirconia agglomerates having grain sizes ranging from 1.0 to 2.0 m. Zirconia agglomerates began to appear at a temperature of 1500 °C and the duplex spinel-ZrO₂ structure was formed with the weight ratio of Al₂O₃/MgO being within 1.67 to 2.20 and the amount of ZrO₂ addition being within 5 to 25 wt %. The relative density, fracture toughness, flexural strength, and critical temperature difference of the spinel-ZrO₂ composite were 97.8%, 1.98 MPam^0.5, 390 MPa, and 275 °C, respectively.     

Dependence of giant magnetoresistance on microstructures in ion-beam co-sputtered CoxAg1−x granular films

A number of structural analysis methods were employed to investigate the microstructures of ion-beam co-sputtering of Co _x Ag_1–x (0x100 at%) granular films. Forx=22 at%, the sample which has the optimal giant magnetoresistance at room temperature, there exists either crystallized or highly disordered regions shown by high-resolution electron microscopy. At the boundary between cobalt granules and the silver matrix, lattice mismatch was formed, leading to roughness of the interfaces. X-ray diffraction and transmission electron microscopy revealed that the samples had f c c structure at lowx, with (111) texture, and the h c p structure gradually appeared as x>75 at %. Relative lattice expansion was observed asx increased.     

Magnetic compass fault detection method for GPS/INS/magnetic compass integrated navigation systems

This paper proposes a magnetic compass fault detection method for GPS/INS/Magnetic compass integrated navigation systems. The fault is assumed to be caused by the hard iron and soft iron effect and modeled as an abrupt change in the magnetic compass output. In order to detect the fault, a test statistic related with only azimuth error measurement is determined. When a fault is detected, the GPS/INS/Magnetic compass integrated navigation system is changed into a GPS/INS integrated navigation system mode. In order to show the validity of the proposed method, computer simulation and van testing are carried out. The simulation and van test results show that the proposed navigation system gives more accurate outputs than the GPS/INS/Magnetic compass without the proposed method.     

自动测试系统中的仪器设备驱动通用封装研究

在目前的自动测试系统软件开发中,虚拟仪器设备指令的非通用性会导致系统开发繁琐、无法集成等问题,针对这些问题提出了一种适合大部分仪器设备的封装方法;这种封装方法,通过动态链接库的形式将事件处理机制嵌入到仪器驱动封装里,拥有跨平台、适用面广、开发速度快和仪器可互换等特点;经过在实际雷达射频模块自动测试系统项目中的应用,结果表明该方法能够实现跨平台操作、具有仪器互换和封装简便等特点,并且表现出极强的通用性,具有一定的实用性和推广价值.     

Transformation of a thin-walled solid model into a surface model via solid deflation

A simplified geometric model with lower dimensionality, such as a mid-surface model, is often preferred over a detailed solid model for the analysis process, if the analysis results are not seriously impacted. In order to derive a mid-surface model from a thin-walled solid model, in this paper, we propose a novel approach called the solid deflation method. In this method, a solid model is assumed to be created by using air to inflate a shell that comprises the surface of the solid model. First, the model is simplified by the removal of any detailed features whose absence would not alter its overall shape. Next, the solid model itself can be converted into a degenerate solid model with zero thickness. Finally, a surface model is generated by splitting large faces paired in the thinned solid model, selecting one face per pair for creating a sheet model, and sewing the selected faces. Using this method, a more practical and usable mid-surface model can be very efficiently generated from a solid model because it can circumvent not only the tedious trimming and extension processes of the medial axis transformation method but also the time-consuming patch joining process of the mid-surface abstraction approach.     

An adaptive load balancing management technique for RFID middleware systems

In recent years, Radio Frequency Identification (RFID) industries have taken a great interest in utilizing the benefits of RFID for supply chain management, inventory control and various other applications. This paper proposed an adaptive load balancing technique for RFID middleware systems to meet the demands of scalability and heterogeneity. First, we explored five basic load balancing policies, namely, information policy, job selection policy, transfer policy, initiation policy and location policy. Eighteen load balancing schemes were then proposed for RFID middleware systems that were combinations of various types of the five basic load balancing policies. Our empirical study suggested that these load balancing strategies performed differently under different workload statuses. Finally, an adaptive load balancing strategy was proposed. The load balancing schemes and the proposed adaptive load balancing strategy have been implemented in the RFID Middleware Load Management System (RM‐LMS). Copyright © 2010 John Wiley & Sons, Ltd.