Quantitative determination of aflatoxin B1 in chick liver

A method for the rapid and quantitative determination of aflatoxin B1 from small quantities of liver, around 1-2 g, is described. The extraction procedure involves acidification to pH 2 of the aqueous liver homogenates, extraction with chloroform: acetone and HPLC-fluorimetric detection after derivatization with trifluoroacetic acid. Quantitative recovery of aflatoxin B1 from chick liver was achieved and detection at levels of 0.2-1 ppb was proved feasible. The aflatoxin B1 concentration in chick liver after oral administration is also shown.     

Dissolution Profiling of Six Modified-Release Oral Solid Dosage Forms

Dissolution testing was conducted for six non-combination, single entity, modified-release oral solid dosage forms. Dissolution medium was water and 0.1 N hydrochloric acid. USP Apparatus 1 and Apparatus 2 were used arid were rotated at either 50 or 100 rpm. A complete dissolution profile was obtained for all six dosage forms based on their stated dosing interval, D. The three strengths of Theo-dur tablets, Norpace CR 150 mg capsules, and the two strengths of Chlor-trimeton tablets passed the Compendial Case One requirements (USP XXI, 2S, 1906). Thorazine spansules and Quinidex tablets were unable to meet the specifications with water as the dissolution medium; the latter showed improved dissolution character in 0.1 N hydrochloric acid. Tenuate Dospan 75 mg tablets showed good release characteristics in water when the authentic (dosing interval (D = 24 hours) was changed to a modified dosing interval of D* = 12 hours. All dissolution aliquots were assayed by UV absorbance measurements at the absorbance maximum for each drug and were also checked for excipient interference. Newer drugs appearing on the market will be more likely candidates for meeting compendial specifications; modified-release pharmaceuticals that appeared before the new specifications may have to be allocated specifically expanded window percentages.     

Dynamic viscosities of mixtures of n-butyraldehyde and isobutyraldehyde over wide ranges in the state parameters

Dynamic-viscosity measurements are reported for liquid mixtures in the system formed by n-butyraldehyde and isobutyraldehyde.Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 48, No. 2, pp. 321–322, February, 1985.     

Pesticide monitoring programme of the Ministry of Health of Brazil

The structure of the recently introduced Brazilian government programme for monitoring pesticide residues in six major agricultural products is described. Residues found from the analysis of samples of tomatoes and strawberries are discussed in detail. The much greater frequency of detection of pesticide residues, many of which are not approved for use in Brazil, in produce being sold on the domestic market, as opposed to that produced for export, is of major concern. It is perceived that this new monitoring programme will become permanent and be used to underpin enforcement actions that will need to be taken to reduce the numbers of incidents of illegal residues occurring, particularly in fresh fruits and vegetables.     

Production of maraging steel grades and the influence of specified and nonspecified elements for special applications

The material properties of maraging steels are greatly affected by the alloy and inclusion content and hence by the production route. This paper describes various past and current production routes at Böhler Edelstahl GmbH and the effect of these routes on the specified element (alloy) and non-specified element (inclusion) contents. Non-metallic inclusions were investigated by EDX analysis. The effects of various alloying and tramp elements on the material properties are presented as a statistical evaluation of previous melts. Nitrogen solubility was calculated with Thermo–Calc for maraging steel Mat.-No. 1.6354 and the precipitation of nitrides is discussed. A proposal is made for the production of melts with improved properties.     

High-strain-rate superplasticity of nanocrystalline aluminum alloy 1570

The structure and mechanical properties of nanocrystalline aluminum alloy 1570 obtained by means of severe plastic deformation have been studied. Being tested in a temperature range from 300 to 400°C, the alloy exhibits high-strain-rate superplasticity. At 400°C, the superplasticity is manifested in a very broad range of strain rates, extending from 5 × 10^?3 to 1 s^?1.     

Simulation of the initial stages of nucleation and growth of Au/NaCl(100)

The results of a computer simulation of the initial stages of the nucleation and growth of gold on NaCl(100) are presented. A potential energy scaling Monte Carlo model employing a 50 × 50 array, mobile monomers, dimers and trimers, and gold atom vertical “roll up” was used. The parameters in the model were obtained from the work of Robinson and Robins, other published sources and/or found by calculation. Simulations of the migration of single gold adatoms over the surface permitted the determination of the diffusion coefficient as a function of the reciprocal temperature which returned the same activation energy given by the potential field, thus indicating the consistency of the model. Initial cluster densities were determined using deposition rates of R_d = 10¹⁵cm^-2s^-1 and R_d = 10¹⁴cm^-2s^-1 over the temperature range T=200–425 K. Initial cluster growth was found to occur primarily by surface phase transport and resulted in clusters that were shaped like very thin disks. Using the equations from the work of Velfe and coworkers, calculations were made to extrapolate the computer simulation data in order to permit an indirect comparison with the data of Robinson and Robins. Good agreement was achieved. Initial condensation coefficients determined over a 250 ms interval showed that α ≈ 0 at T > 425 K and α ≈ 1 at T < 325 K for a deposition rate of R_d=10¹⁵ cm^-2 s^-1.     

Optical characteristics of waste stabilization ponds: recommendations for monitoring.

The optical character of waste stabilization ponds (WSPs) is of concern for several reasons. Algal photosynthesis, which produces oxygen for waste oxidation in WSPs, is influenced by attenuation of sunlight in ponds. Disinfection in WSPs is influenced by optical characteristics because solar UV exposure usually dominates inactivation. The optical nature of WSPs effluent also affects assimilation by receiving waters. Despite the importance of light behaviour in WSPs, few studies have been made of their optical characteristics. We discuss simple optical measures suitable for routine monitoring of WSPs (including at sites remote from laboratories): optical density of filtrates - an index of dissolved coloured organic (humic) matter, visual clarity - to provide an estimate of the beam attenuation coefficient (a fundamental quantity needed for optical modelling) colour (hue) - as an indicator of general WSP 'condition' and irradiance attenuation quantifying depth of light penetration. The value of optical characterisation of WSPs is illustrated with reference to optical data for WSPs in NZ (including high-rate algal ponds) treating dairy cattle wastewater versus domestic sewage. We encourage increased research on optical characteristics of WSPs and the incorporation of optical measures in monitoring and modelling of WSP performance.     

An integrated system to remote monitor and control anaerobic wastewater treatment plants through the internet.

The TELEMAC project brings new methodologies from the Information and Science Technologies field to the world of water treatment. TELEMAC offers an advanced remote management system which adapts to most of the anaerobic wastewater treatment plants that do not benefit from a local expert in wastewater treatment. The TELEMAC system takes advantage of new sensors to better monitor the process dynamics and to run automatic controllers that stabilise the treatment plant, meet the depollution requirements and provide a biogas quality suitable for cogeneration. If the automatic system detects a failure which cannot be solved automatically or locally by a technician, then an expert from the TELEMAC Control Centre is contacted via the internet and manages the problem.