High-velocity impact experiment of aluminum foam sample using powder gun

Porous materials such as aluminum foam have been investigated for possible use as impact shock absorbers in transportation aeronautic applications. However, the response of aluminum foam during impacts at high velocities of more than 100 m/s is not yet fully understood. A high-velocity impact experiment was therefore carried out to clarify impact shock absorption properties of aluminum foam. A one-stage powder gun was used to accelerate an aluminum foam sample to impact a rigid wall. Velocity and deformation of the aluminum foam sample during impact was studied using a digital high-speed video camera, while the pressure wave in the aluminum foam sample was measured using a PVDF gauge. The experimental observations revealed uneven collapse of the aluminum foam sample structure during high speed impact with a general stress plateau effect, typical for cellular material structures when subjected to quasi-static loading.     

Fabrication of submicron alumina ceramics by pulse electric current sintering using M2+ (M = Mg,Ca, Ni)-doped alumina nanopowders

Dense submicron-grained alumina ceramics were fabricated by pulse electric current sintering (PECS) using M²⁺(M: Mg, Ca, Ni)-doped alumina nanopowders at 1250 °C under a uniaxial pressure of 80 MPa. The M²⁺-doped alumina nanopowders (0–0.10 mass%) were prepared through a new sol–gel route using high-purity polyhydroxoaluminum (PHA) and MCl₂ solutions as starting materials. The composite gels obtained were calcined at 900 °C and ground by planetary ball milling. The powders were re-calcined at 900 °C to increase the content of α-alumina particles, which act as seeding for low-temperature densification. Densification and microstructural development depend on the M²⁺ dopant species. Dense alumina ceramics (relative density ≥99.0%) thus obtained had a uniform microstructure composed of fine grains, where the average grain size developed for non-doped, Ni-doped, Mg-doped and Ca-doped samples was 0.67, 0.67, 0.47 and 0.30 μm, respectively, showing that Ca-doping is the most promising method for tailoring of nanocrystalline alumina ceramics.     

Preparation of novel porous solids from alumina-pillared fluorine micas by acid-treatment

New porous solids from alumina-pillared fluorine micas (APMs), which were obtained from synthetic Na-tetrasilicic fluorine mica [NaMg_2.5Si₄O₁₀F₂], were prepared by sulfuric acid-treatment under mild conditions at 25 °C. The products were investigated by XRD, ICP, SEM, TEM and N₂ adsorption–desorption isotherm at 77 K. XRD measurements indicated that the interlayer pillared structure having a large basal spacing collapsed during the early stages of the acid-treatment. ICP analyses indicated that Al³⁺ and Mg²⁺ ions were leached out from the pillared micas during the acid-treatment. The pore properties of the leached products were found to differ from those of the mother pillared micas: the acid leaching of the pillared micas leads to the formation of mesopores around 3.2 nm in diameter. The correlation between the change in pore properties and cation elution behavior suggests that the mesopore formation results from the leaching of Mg²⁺ ions from the octahedral sheet of the pillared micas. The leached products thus obtained retained the flaky morphology of the mother pillared micas. These results show that the mild acid-treatment using APMs provides a novel route for obtaining unique mesopore solids having the large particle sizes of the mother micas.     

Temperature control for the expansion of artificial DNA motif

The DNA, which forms a double helical conformation by the highly selective base-pairing rule with the width of 2 nm, is one of the polymers utilized as a template for nanoparticle assembly. Then, holiday junction structure, where two different DNA double strands intersect and replace each complement strand, is an important artificial motif for forming two-dimensional mesh-like DNA morphology. In this study, the two-dimensional sheet with the mesh-like conformation is formed and the growth of the DNA morphology is controlled by changing the temperature in the formation process. The influence of the cooling procedure on the formation process of the two-dimensional DNA sheet is observed by atomic force microscope, and the formation of double strands in the process is traced by absorption spectra. The spectroscopic results demonstrate that the two-dimensional DNA sheet is strongly dependent on the correlation between the applied cooling process and the melting temperature of double helical conformation, and that the growth of the two-dimensional DNA sheet can be manipulated by the cooling procedure. Further, we will show the size control of the DNA sheet by mixing the designed DNA which inhibits the growth of the DNA sheet.     

Feature extraction by supervised independent component analysis based on category information

Independent component analysis (ICA) is a technique of transforming observation signals into their unknown independent components; hence, ICA has often been applied to blind signal separation problems. In this application, it is expected that the obtained independent components extract essential information of independent signal sources from input data in an unsupervised fashion. Based on such characteristics, ICA is currently utilized as a feature extraction method for images and sounds for recognition purposes. However, since ICA is an unsupervised learning, the obtained independent components are not always useful in recognition. To overcome this problem, we propose a supervised approach to ICA using category information. The proposed method is implemented in a conventional three‐layered neural network, but its objective function to be minimized is defined not only for the output layer but also for the hidden layer. The objective function consists of the following two terms: one evaluates the kurtosis of hidden unit outputs and the other evaluates the error between output signals and their teacher signals. The experiments are performed using several standard datasets to evaluate performance of the proposed algorithm. It is confirmed that a higher recognition accuracy is attained by the proposed method as compared with a conventional ICA algorithm. © 2007 Wiley Periodicals, Inc. Electr Eng Jpn, 161(2): 25–32, 2007; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20522     

同质外延CVD金刚石膜的室温边发射

利用高功率微波等离子体化学气相沉积方法及合适的预处理方法成功地合成了无生长丘的高品质金刚石膜，阴极荧光（CL）结果表明在本工作的同质外延金刚石膜中，边发射在室温下也是主峰之一。详细研究了室温下有异常粒子和无异常粒子的样品的CL谱和CL扫描图，发现边发射主要产生于无异常粒子区域。而大多数异常粒子主要对位于425nm的BandA发射起作用，因此抑制异常粒子的形成对提高同质外延金刚石摸的质量非常重要。     

Phase relations associated with the aluminum blast furnace: Aluminum oxycarbide melts and Al-C-X (X=Fe,Si) liquid alloys

The thermodynamic properties and the phase relations were evaluated and estimated for the Al-O-C, Al-Si-C, and Al-Fe-C systems which are important to understand the chemical behavior in an aluminum blast furnace. The mixing properties of binary liquid alloys, including metal-carbon systems, were represented by the Redlich-Kister equation. The properties of liquid Al−C and Si−C alloys were estimated so as to be consistent with their phase diagrams. The coefficients of Al−Fe and Fe−C liquids were evaluated from reported values for activity and enthalpy. The extrapolation to the higher order systems was made by Maggianu's method. The aluminum oxycarbide melt was represented by a subregular solution model. In the Al-O-C system, liquid alloy/oxycarbide melt equilibria were calculated and compared with earlier experimental results and estimates. Attempts were made to clarify the volatilization of aluminum oxycarbide melts, and also the carbidation of liquid aluminum alloys. An empirical correlation between the first terms of the Redlich-Kister equation for the enthalpies and the excess entropies was discussed.     

HU-PACS. 10 months experience.

An outline of the Hokkaido University PACS (HU-PACS) and 10 months experience of its clinical use are reported. It is concluded that HU-PACS is a useful clinical tool, even though some points still remain to be improved.     

Cloning and some properties of Japanese pear (Pyrus pyrifolia) polyphenol oxidase,and changes in browning potential during fruit maturation

A PCR‐amplified genomic DNA fragment encoding Japanese pear (Pyrus pyrifolia) polyphenol oxidase (PPO) was cloned and sequenced. The DNA appears to encode a 66 kDa precursor protein consisting of a 56 kDa mature protein and a 9.5 kDa N‐terminal transit peptide. The amino acid sequence showed high homology with apple PPO. The PPO mainly existed as a soluble fraction in cells and was limitedly proteolysed, while the mature form (56 kDa) was detected in plastids. Immature fruits showing high browning potential had high PPO activity and a high level of phenolics, while mature fruits showing little browning had high PPO activity but a low level of phenolics. Copyright © 2003 Society of Chemical Industry