Performance characteristics of energy separation in a steam-operated vortex tube

Energy separation performance of a steam-operated vortex tube is experimentally investigated, and some reasonable criteria and expressions to estimate the energy separation performance are also introduced. The performance characteristics defined by the above expressions are the same as those of ideal gas in the high superheated region, and are well expressed independently of the degree of superheat, total mass flow rate and discharge resistance. When steam is in the wet region at the nozzle outlet, the performance considerably decreases because of the energy waste from moisture vaporization. And no energy is separated when the dryness fraction is less than approximately 0.98. Some technical data including the optimum operating conditions are also offered.     

Synthesis of Nanohole‐Structured Single‐Crystalline Platinum Nanosheets Using Surfactant‐Liquid‐Crystals and their Electrochemical Characterization

Nanohole‐structured single‐crystalline Pt nanosheets have been synthesized by the borohydride reduction of Na₂PtCl₆ confined to the lyotropic liquid crystals (LLCs) of polyoxyethylene (20) sorbitan monooleate (Tween 80) with or without nonaethylene‐glycol (C₁₂EO₉). The Pt nanosheets of around 4–10 nm in central thickness and up to 500 nm or above in diameter have a number of hexagonal‐shaped nanoholes ∼1.8 nm wide. High‐resolution electron microscope images of the nanosheets showed atomic fringes with a spacing of 0.22 nm indicating that the nanosheets are crystallographically continuous through the nanoholed and non‐holed areas. The inner‐angle distributions for the hexagonal nanoholes indicate that the six sides of the nanoholes are walled with each two Pt (111), Pt (1 1) and Pt (010) planes. The formation mechanism of nanoholed Pt nanosheets is discussed on the basis of structural and compositional data for the resulting solids and their precursory LLCs, with the aid of similar nanohole growth observed for a Tween 80 free but oleic acid‐incorporated system. It is also demonstrated that the nanoholed Pt nanostructures loaded on carbon exhibit fairly high electrocatalytic activity for oxygen reduction reaction and a high performance as a cathode material for polymer‐electrolyte fuel cells, along with their extremely high thermostability revealed through the effect of electron‐irradiation.     

Fatigue and fracture behavior in notched specimens of C/C composite with fine-woven carbon fiber laminates

Fatigue and fracture behavior of C/C composite with fine-woven carbon fiber laminates was investigated in several schemes of notched specimens. Slits and holes were cut in the specimens as notches, and the effect of fiber orientation and notch configuration on the fatigue behavior was examined. The fatigue limit was defined by a simple method that used incremental applied stress and number of cycles. The fatigue limit was dependent on fiber orientation, notch configuration and stress ratio (ratio of minimum cyclic stress to maximum cyclic stress). It was found that the fatigue limit was determined by the true stress rather than by the stress concentration in the present material and was not affected by variations in slit depth. Also, the fracture behavior was controlled by shear deformation.     

Obui-himo syndrome

Normal variants of the venous system are relatively common and rarely cause severe symptoms. We report the case of a 5-month-old baby who displayed cyanotic color and swelling of arms whenever she was carried on the mother's back with a special band "Obui-himo". It was demonstrated by venography that the symptoms were caused by the absence of a cephalic vein and compression of axillary veins with the Obui-himo. In any country with a custom similar to the Obui-himo, these symptoms, if clinically encountered, are an indication that venography should be performed.     

Development of ultra-deep HDS catalyst for production of clean diesel fuels

Cosmo Oil has successfully developed a new CoMo HDS catalyst, C-606A, for production of ultra-low sulfur diesel fuels. This catalyst was prepared by an impregnation method using a solution containing Co, Mo, P, and citric acid on a HY-Al₂O₃. The resulting catalyst air-dried only without calcination. The HDS activity was measured with straight-run light gas oil feedstocks under industrial hydrotreating conditions. C-606A had a three times higher HDS activity compared with the conventional CoMoP/Al₂O₃ catalyst. Commercial operation with C-606A has successfully demonstrated high performance. This catalyst has superior activity, which enables <10-ppm sulfur content in products in a commercial hydrotreater designed to produce 500-ppm sulfur diesel fuels.     

Keratanase II-catalyzed synthesis of keratan sulfate oligomers by using sugar oxazolines as transition-state analogue substrate monomers: a novel insight into the enzymatic catalysis mechanism

Keratan sulfate (KS) oligomers with well-defined structures were synthesized by keratanase II (KSase II)-catalyzed transglycosylation. N-Acetyllactosamine [Galbeta(1-->4)GlcNAc; LacNAc] oxazoline derivatives with sulfate groups at the C-6 (1 a) and both the C-6 and the C-6' (1 b) were prepared as transition-state analogue substrate monomers for KSase II. Monomer 1 a was effectively oligomerized by the enzyme under weak alkaline conditions, to give alternating 6-sulfated KS oligomers (2 a) in good yields, and with total control of regioselectivity and stereochemistry. KSase II also recognized 1 b, which provided fully 6-sulfated KS oligomers (2 b) in good yields under similar conditions. Nonsulfated LacNAc oxazoline was difficult to oligomerize enzymatically. These results imply that the catalysis mechanism of KSase II involves a sugar oxazolinium ion that requires the 6-sulfate group in the GlcNAc residue not only in hydrolysis of KS chains, but also in oligomerization of oxazoline monomers. This is the first report of KSase II-catalyzed transglycosylation to form beta(1-->3)-glycosidic bond through a substrate-assisted mechanism.     

Image analysis of morphological change during arachidonic acid production by Mortierella alpina 1S-4

The changes in mycelial morphology during arachidonic acid (AA) production by Mortierella alpina 1S-4 were investigated using an image analysis system. Cultivation was performed in a 10-kl fermentor, and the culture broth was separated into two fractions by sieving (0.5 mm aperture size): the filament fraction (F-fraction, <0.5 mm), and the pellet fraction (P-fraction, >0.5 mm). The effect of the mycelial morphology in each fraction on AA production was analyzed. As a result, a product distribution in the culture broth wherein the AA content in the mycelia of the P-fraction was observed to be higher than that in the mycelia of the F-fraction throughout the cultivation. Morphological analysis of the P-fraction revealed that the hairy pellets became smooth because the mycelia on the pellet surface were shaved off; some pellets were broken and reduced in size. The shaved-off mycelia from the hairy pellets surface moved into the F-fraction and aggregated there. From the above findings, it was likely that the low AA content in the F-fraction was due to mycelial damage during the cultivation. In addition, the morphology of the hairy pellets was found to contribute to an increase in the viscosity of culture broth.     

Corrosion behavior of various steels in the simulated fluidized bed boiler environment

The corrosion behavior of various austenitic stainless steels and high-alloy steels has been studied in simulated fluidized bed boiler environment to develop a new corrosion resistant austenitic stainless steel for the superheater tube. The superheater is usually not installed within the bed position, which is different from the evaporator installed within the bed position. Therefore, the superheater tubes are exposed to an oxidizing environment; but it is also necessary to estimate the corrosion resistance of the steels in a reducing environment. It is already known that the high temperature corrosion behavior in conditions where CaSO₄ is coated on the steels is more important than the erosion of the superheater tubes. The main results in this present study are as follows: The Nb bearing steels and low C steels showed good resistance to high-temperature corrosion in CaSO₄/CaO, e.g. 347, 304L and HR3C. The corrosion rate of all steels used increased with increase in temperature, particularly at temperatures higher than 650°C. Internal penetration was not detected at temperatures lower than 550°C, but it was detected at temperatures higher than 600°C, in particular, higher than 650°C. The corrosion thickness loss was almost the same as the internal penetration depth at 700 and 750°C in the 300 series steels placed in CaSO₄/CaO, including the fine grained 347 steel, while the internal penetration depth was larger than the corrosion thickness loss in high-alloyed materials such as Alloy 800 and 310 steels. At temperatures higher than 800°C, the same result was also obtained for the fine grained 347 steel. The corrosion during exposure to oxidizing or reducing gases without CaSO₄/CaO or CaS was slight, but when the test specimens were placed in CaSO₄/CaO or CaS, the corrosion rate sharply increased, regardless of the atmospheric gas composition. Cr, Si, Mn (less than 5 %), Mo and Nb are beneficial elements while C, Cu and Al are harmful elements. From the above results, the following steel was developed for high temperature corrosion resistance in CaSO₄/CaO: low C-22/25Cr-17/25Ni-3/5Mn-(2Mo)-Nb-0.08/0.2N-Al-(B).