HEAT AND MASS TRANSFER IN THE ADSORBENT BED OF AN ADSORPTION HEAT PUMP

The heat and mass transfer equations governing an adsorbent bed in an adsorption heat pump and the mass balance equation for the adsorbent particles in the adsorbent bed were solved numerically to simulate the cycle of a basic adsorption heat pump, which includes isobaric adsorption, isosteric heating, isobaric desorption, and isosteric cooling processes. The finite difference method was used to solve the set of governing equations, which are highly nonlinear and coupled. The pressures of the evaporator and condenser were 2 and 20 kPa, respectively, and the regeneration temperature of the bed was 403 K. Changes in the temperature, adsorptive pressure, and adsorbate concentration in the adsorbent bed at different steps of the cycle were determined. The basic simulated cycle is presented in a Clausius-Clapeyron diagram, which illustrates the changes in average pressure and temperature of the adsorbent bed throughout the cycle. The results of the simulation indicated that the most time-consuming processes in the adsorption heat pump cycle were isobaric adsorption and isobaric desorption. The high thermal resistance of the bed slows down heat transfer, prolonging adsorption and desorption processes.     

Effect of calcium hydroxide removal techniques on the bond strength of root canal sealers

To evaluate the influence of calcium-hydroxide(CH) with different vehicles on the push-out bond strength of different canal sealers to radicular dentin. 152 decrowned single-rooted human teeth were used. After preparation of root canals with nickel-titanium rotary files, 8 roots served as control groups. Then, the roots were divided as follows: (1) Calasept and (2) Surepaste (n = 72). Roots were further subgrouped according to the CH removal techniques: (1) %17 ethylenediaminetetraacetic acid (EDTA) + rotary file, (2) %17EDTA + hand file, and (3) %17EDTA (n = 24). Eight roots from each group sectioned longitudinally, divided into two pairs and photographed by stereomicroscope (n = 16). The remaining 16 roots in CH intracanal dressing groups were further divided into 2 subgroups according to the sealer used: (1) AH-Plus-jet and (2) Apexit-Plus (n = 8). Bond strengths of the root canal sealers to root canal dentin were measured using a push-out test setup. The data were statistically analyzed using multivariate analysis of variance p = 0.05. The push-out bond strength values were significantly affected by type of vehicle and the removal techniques (p < 0.05). The mean bond strength of AH-Plus-jet was significantly higher than Apexit-Plus, regardless of type of vehicle and the removal techniques (p < 0.05). There was no difference between vehicles on CH removal (p > 0.05). When examining the removal techniques, only irrigation with %17 EDTA left significantly larger amount of residue (p < 0.05). AH-Plus-jet showed better dislocation resistance than Apexit-Plus. Type of vehicle does not play a fundamental role in the degree of persistence of CH residues on the dentin walls. Instrumentation improves the removal efficiency of CH from root canal.     

Regeneration of Used Frying Oil

Used frying oils were purified in a packed column using different amounts of silica gel (SG), aluminum oxide (AO), activated charcoal (AC), bentonite (B), magnesol XL (M), calcium carbonate (CC), zeolite (Z), bleaching earth (BE) and/or their binary, triple, and quaternary combinations. SG (15 g) improved total polar material (TPM) by 100 %, conjugated diene (CD) content by 84 %, and p-anisidine value (AV) by 104 %, while AO and M improved free fatty acid (FFA) contents by 103 and 105 %, respectively. On the other hand, AC and M bleached the color by 100 and 90 %, respectively. As the amount of adsorbent in the column increased, FFA, CD, AV, and color improved. When the amount of used sunflower oil (UO1) loaded in the column containing SL was increased, FFA, CD, AV and color values increased, while no change was observed in TPM up to 60 g of UO1. Loading UO1 at 150 °C in the column caused the absorbance values at 460 nm to decrease from 0.740 to 0.240, while the amount of adsorbed tocopherol increased compared to UO1 at 25 °C. The increasing number of adsorbents within the column further improved the physicochemical properties of UO1 when it was used 30 g. However, as the amount of different type of used oils (UO2, UO3 and UO4) was increased to 300 g, improvement ratios of all parameters decreased.     

Monolayer and bilayer conducting polymer coatings for corrosion protection of steel in 1 M H2SO4 solution

In this study, monolayer polypyrrole (PPY), polyaniline (PANI), and bilayer PPY/PANI, PANI/PPY coatings were deposited onto steel electrodes by electropolymerization in 0.1 M monomer and 0.3 M oxalic acid solution. Such corrosion parameters of these electrodes, as corrosion potentials, anodic Tafel constants and corrosion current densities were determined by means of current–potential curves as a function of time in 1 M H₂SO₄ solution. These findings were compared to the corrosion parameters of a bare steel electrode in the same acid solution. The monolayer and bilayer polymer coatings were characterized by the Fourier transform infrared (FTIR) spectroscopy and SEM. Bilayer coatings displayed better corrosion inhibition efficiencies than monolayer coatings. Furthermore, the PPY/PANI coatings offered superior corrosion protection than the PANI/PPY coatings.     

Flow characteristics of a small moving bed downcomer with an orifice under negative pressure gradient

Behaviour of gas-solid mixtures in a small moving bed downcomer operating under negative pressure gradient has been investigated experimentally, because flow characteristics in a downcomer are important factors in powder handling processes, such as a multi-stage spouted bed or a circulating fluidized bed. In this study, a small downcomer in which the moving bed height could be controlled was employed with the intention of using a downcomer as a connecting tube in a multi-stage spouted bed. Based on experimental observation, the moving bed flow changed from smooth flow (Region(I)) to slip-stick flow (Region(II)) and then changed from slip-stick flow to intermittent flow (Regime(III)), as the gas pressure gradient in the downcomer was increased. In this study, the critical point for steady-state (Region(I)) operation was also examined experimentally and theoretically, by using eight kinds of solid particles (Geldart B, D and A powders) and six different orifice sizes which were used to restrict solids flow at the base of the downcomer. As a result, a correlation of solids flow rate in the stable moving bed downcomer under negative pressure gradient was derived and the critical point between stable and unstable flow was explained by the proposed model.     

Phosphate inhibition on thermophilic acetoclastic methanogens: a warning.

The inhibitory effect of phosphate on acetoclastic-methanogens was investigated for three different thermophilic (55 degrees C) anaerobic consortia. When 70 mM of phosphate was tested, acetoclastic methanogens was completely inhibited in "Eerbeek" sludge which is dominated by Methanosaeta-like methanogens. For the "Hoogezand" sludge the specific methanogenic activity dropped by 79%, indicating that any of the acetate-consuming methanogens present in the sludge was more resistant to the phosphate applied. The results demonstrated that the inhibitory effect of phosphate may affect both methane production rate and final methane concentration and might also be time dependent. This study indicates that the degree of inhibition is species-dependent, and even more resistant species may be affected during long-term experiments. Such inhibition is a matter of concern for researchers since misleading conclusions might be taken from growth and specific methanogenic activity tests when considerable concentrations of phosphate buffer are used and no interference is expected.     

Thermal degradation characteristics of oil‐filled cable joint with extremely degraded tan δ oil

Much of oil‐filled (OF) cable has been used for a long time as 66‐ to 500‐kV extrahigh‐voltage cable. Sometimes we can see extremely degraded tan δ oil (several tens of percent of tan δ, for example) in joint boxes, etc. The values of tan δ calculated by a simple combination model of paper/oil show that the oil‐impregnated paper with such a high tan δ oil likewise has an extremely high tan δ, which must result in thermal breakdown. However, such an event has not taken place up to the present in actually operated transmission lines. This fact suggests that some mechanism for the suppression of tan δ has acted in the paper insulation impregnated with degraded tan δ oil. Therefore, we investigated in detail the tan δ characteristics of paper impregnated with extremely high tan δ oil. In addition, based on the investigation results, we developed a method for simulation of heat generation by dielectric loss in an OF cable joint (which has degraded tan δ oil). © 2011 Wiley Periodicals, Inc. Electr Eng Jpn, 178(1): 1–10, 2012; Published online in Wiley Online Library ( wileyonlinelibrary.com ). DOI 10.1002/eej.21184     

Polystyrene and poly(methyl methacrylate) interfaces reinforced with diblock carbon nanotubes

An asymmetric double cantilever beam test was used to determine the ability of carbon nanotubes with varying chemistry along their lengths, that is, diblock nanotubes, to compatibilize the polystyrene/poly(methyl methacrylate) (PS/PMMA) interface. PS molecules were grafted primarily to one of the blocks to cause that block to migrate to the PS phase since otherwise both blocks would prefer to reside in PMMA. Fracture toughnesses increased monotonically with increasing diblock carbon nanotube concentration and maximum values were like those for block copolymer-reinforced interfaces while single-chemistry nanotubes showed no reinforcing effect. However, the abrupt increase in fracture toughness with added compatibilizer indicative of a transition to crazing was not found consistent with nanotubes suppressing crazing in homopolymers. Scanning electron microscopy images of the fractured surfaces show agglomerates of carbon nanotubes present which are likely limiting the efficacy of carbon nanotubes at toughening the interface.     

Estimating the imageability of words by mining visual characteristics from crawled image data

Multimedia Tools and Applications - Natural Language Processing and multi-modal analyses are key elements in many applications. However, the semantic gap is an everlasting problem, leading to...     

The evaluation of the emotion by near-infrared spectroscopy

Our purpose is to develop the technology for evaluating emotion objectively from the oxygenated hemoglobin within a brain. Nowadays, Japan is an aging society. The elderly people who need care will increase from now on increasingly. In the case of the person requiring the care who lost the function to convey an intention especially, the objective judgment to a physical and mental pain is required. Persons requiring care will also increase in number with the increase in this population. We gave subject stimulus of a comfortable or an uncomfortable sound and measured concentration of the oxygenated hemoglobin of a frontal lobe part by near-infrared spectroscopy. Based on the experimental result, a comfortable state or an uncomfortable state was distinguished by concentration of the oxygenated hemoglobin using the bayesian network. As a result, we were able to estimate the subject’s psychological condition.