Primary creep behavior of Ti-48Al-2W as a function of stress and lamellar morphology

The fully lamellar microstructure of powder metallurgy Ti-48Al-2W after cooling from the α region to 1280 °C, followed by air cooling and aging at 950 °C for up to 96 hours, is presented. Aging times as short as 5 hours result in acicular-shaped precipitates of W-rich β ₀ along lamellar interfaces, with the β ₀ size increasing with aging time. The β ₀ precipitates nucleate and grow in the α ₂ lamellae. Concurrently, with the formation of β ₀, the α ₂ decomposes into discontinuous lamellae. Aging to precipitate β ₀ along lamellar interfaces increases the 760 °C tensile strength (with a slight reduction of ductility) and reduces the instantaneous creep strain, since β ₀ precipitates at lamellar interfaces hinder interface dislocation mobility. The deformed microstructures from interrupted creep tests at 140 to 276 MPa at 760 °C indicate that the precipitation of β ₀ along interfaces substantially reduces the primary creep strain, primarily due to the influence of β ₀ on interface dislocation emission and motion. These results are discussed in terms of the influence of lamellar morphology on the instantaneous creep strain and primary creep transient, and the possible creep mechanisms are highlighted. This article is based on a presentation made in the symposium entitled “Fundamentals of Structural Intermetallics,” presented at the 2002 TMS Annual Meeting, February 21–27, 2002, in Seattle, Washington, under the auspices of the ASM and TMS Joint Committee of Mechanical Behavior of Materials.     

Improving Korean verb-verb morphological disambiguation using lexical knowledge from unambiguous unlabeled data and selective web counts

This paper deals with verb-verb morphological disambiguation of two different verbs that have the same inflected form. The verb-verb morphological ambiguity (VVMA) is one of the critical Korean parts of speech (POS) tagging issues. The recognition of verb base forms related to ambiguous words highly depends on the lexical information in their surrounding contexts and the domains they occur in. However, current probabilistic morpheme-based POS tagging systems cannot handle VVMA adequately since most of them have a limitation to reflect a broad context of word level, and they are trained on too small amount of labeled training data to represent sufficient lexical information required for VVMA disambiguation.In this study, we suggest a classifier based on a large pool of raw text that contains sufficient lexical information to handle the VVMA. The underlying idea is that we automatically generate the annotated training set applicable to the ambiguity problem such as VVMA resolution via unlabeled unambiguous instances which belong to the same class. This enables to label ambiguous instances with the knowledge that can be induced from unambiguous instances. Since the unambiguous instances have only one label, the automatic generation of their annotated corpus are possible with unlabeled data.In our problem, since all conjugations of irregular verbs do not lead to the spelling changes that cause the VVMA, a training data for the VVMA disambiguation are generated via the instances of unambiguous conjugations related to each possible verb base form of ambiguous words. This approach does not require an additional annotation process for an initial training data set or a selection process for good seeds to iteratively augment a labeling set which are important issues in bootstrapping methods using unlabeled data. Thus, this can be strength against previous related works using unlabeled data. Furthermore, a plenty of confident seeds that are unambiguous and can show enough coverage for learning process are assured as well.We also suggest a strategy to extend the context information incrementally with web counts only to selected test examples that are difficult to predict using the current classifier or that are highly different from the pre-trained data set.As a result, automatic data generation and knowledge acquisition from unlabeled text for the VVMA resolution improved the overall tagging accuracy (token-level) by 0.04%. In practice, 9-10% out of verb-related tagging errors are fixed by the VVMA resolution whose accuracy was about 98% by using the Naïve Bayes classifier coupled with selective web counts.     

Plasmon Enhanced Fluorescence Based on Porphyrin–Peptoid Hybridized Gold Nanoparticle Platform

A porphyrin–peptoid‐hybridized silica‐coated gold nanoparticle is developed, which is inspired by the protein–chlorophyll ensemble found in photosynthetic antenna. In the natural antenna, chlorophylls are integrated into dense assemblies that are supported by frameworks of proteins, which ensure optimal pigment arrangement for effective light harvesting. In the subject platform, porphyrins are conjugated to the peptoid helix scaffold in a structurally well‐defined alignments and subsequently immobilized on the surface of nanoparticles. This prevents intermolecular aggregation among porphyrins and allows high resolution analysis of the effect of porphyrin configuration on the optical properties of the system. Interestingly, under the influence of plasmon from the gold nanoparticle core, the fluorescence of porphyrin is enhanced up to 24‐fold at the wavelength where the plasmon resonance matches the porphyrin excitation wavelength. In addition, differences in porphyrin configuration result in spectral modification of their fluorescence emissions. Particularly, the peptoid bearing two porphyrins at a distance of 6 Å shows the most significant alteration in fluorescence. The platform can facilitate extensive studies on the relationship between porphyrin arrangement design and their photophysical interaction in antenna complexes.     

Growth time-dependent density and surface evolution of silicon nanowires in a vapor-liquid-solid process

Single crystalline silicon nanowires (SiNWs) were grown on Si(100) substrate using a gold (Au)-catalyzed vapor-liquid-solid (VLS) approach. The dependence of the growth time (i.e., the time of exposure to the Si source) on the density and surface evolution of the grown SiNWs is considered. It was observed that the density of grown SiNWs on Si substrate increased with increasing growth time. The highest density (approximately 1.1 x 10(6) mm(-2)) was reached at 4 hr. Upon further exposure to the Si source, we observed that the density was maintained for up to 9 hr. We suggest that the increased Si chemical potential in Au-Si droplets with increased growth time enhanced the SiNW growth rate at the interfaces between Au-Si droplets and SiNWs, and enhanced the transition of the NWs from the existing Au-Si droplets onto Si substrate. This allows the SiNW density to increase with increased growth time of up to 4 hr. Moreover, we examined the influence of the growth time on surface evolution including Au diffusion, facet and taper formation, and vapor-solid (VS) growth of the SiNWs. To explain the behavior of the grown SiNWs in the VLS process, we propose a combined model using the VLS and VS growth mechanisms.     

Investigation of Potassium Storage in Layered P3‐Type K0.5MnO2 Cathode

Novel and low‐cost batteries are of considerable interest for application in large‐scale energy storage systems, for which the cost per cycle becomes critical. Here, this study proposes K_0.5MnO₂ as a potential cathode material for K‐ion batteries as an alternative to Li technology. K_0.5MnO₂ has a P3‐type layered structure and delivers a reversible specific capacity of ≈100 mAh g^?1 with good capacity retention. In situ X‐ray diffraction analysis reveals that the material undergoes a reversible phase transition upon K extraction and insertion. In addition, first‐principles calculations indicate that this phase transition is driven by the relative phase stability of different oxygen stackings with respect to the K content.     

Preparation and characterization of polypropylene/sodium propionate (PP/SP) composite films for bread packaging application

To prolong the shelf life of bread, polypropylene/sodium propionate (PP/SP) composite films were prepared via a melt‐extrusion process. To investigate the feasibility of using PP/SP composite films as a bread packaging material, their chemical structure, morphology, mechanical properties, barrier properties against water, surface properties, and antimicrobial properties were investigated. A storage test for bread was also conducted. The mechanical and thermal stability of the PP/SP composite films enhanced with increasing SP content. Compared with pure PP, the PP/SP composites had increased hydrophilicity that increased with increasing SP content. These composite films showed enhanced antimicrobial activity against both Gram‐negative and Gram‐positive microorganisms. This was due to the interaction of SP and water originating from the bread, which modifies the pH of the bread and causes destruction of the cellular structures of fungi and also reduces the growth rate of bacteria. The enhanced thermal, mechanical, antifungal, and antimicrobial properties achieved by the addition of SP can be beneficial for maintaining the freshness of bread and prolonging its shelf life.     

The effect of substrate temperature on Al-doped ZnO characteristics for organic thin film transistor applications

The influence of substrate temperature on the structural, electrical, and optical properties of aluminum-doped zinc oxide (AZO) films fabricated by radio frequency (RF) magnetron sputtering was investigated. The AZO films were deposited at various substrate temperatures, and the effect of AZO gate electrode conductivity on organic thin film transistor (OTFT) performance was examined. While an increase in the substrate temperature from 100 °C to 300 °C led to an improvement in crystallinity, substrate temperatures over 300 °C caused degradation of the electrical and surface properties. We fabricated OTFTs using AZO films prepared at various substrate temperatures and obtained good device performance. Thus, the performance of an OTFT can be determined by the conductivity of the AZO gate electrode.     

Cactus‐Like Hollow Cu2‐xS@Ru Nanoplates as Excellent and Robust Electrocatalysts for the Alkaline Hydrogen Evolution Reaction

The development of Pt‐free electrocatalysts for the hydrogen evolution reaction (HER) recently is a focus of great interest. While several strategies are developed to control the structural properties of non‐Pt catalysts and boost their electrocatalytic activities for the HER, the generation of highly reactive defects or interfaces by combining a metal with other metals, or with metal oxides/sulfides, can lead to notably enhanced catalytic performance. Herein, the preparation of cactus‐like hollow Cu_2‐x S@Ru nanoplates (NPs) that contain metal/metal sulfide heterojunctions and show excellent catalytic activity and durability for the HER in alkaline media is reported. The initial formation of Ru islands on presynthesized Cu_1.94S NPs, via cation exchange between three Cu⁺ ions and one Ru³⁺, induces the growth of the Ru phase, which is concomitant with the dissolution of the Cu_1.94S nanotemplate, culminating in the formation of a hollow nanostructure with numerous thin Ru pillars. Hollow Cu_2‐x S@Ru NPs exhibit a small overpotential of 82 mV at a current density of ?10 mA cm^?2 and a low Tafel slope of 48 mV dec^?1 under alkaline conditions; this catalyst is among state‐of‐the‐art HER electrocatalysts in alkaline media. The excellent performance of hollow Cu_2‐x S@Ru NPs originates from the facile dissociation of water in the Volmer step.