Study on Laboratory Method for Refining of SR Diesel Fuel

The method for refining the straight-run diesel fuel was studied in laboratory scale in order to make the acid number of diesel fraction comply with the standard while removing the naphthenic acids contained in diesel without causing environmental pollution. After comparing the effect of refining using three solvents, the isopropyl alcohol-HOA was specified as the best solvent. Meanwhile, the relationship between the acid number of diesel fraction and the amount of solvent used and the relationship between the concentration of solvent and temperature and the stability of diesel in terms of its acid number were also investigated. Experimental results had shown that when the mass fraction of the HOA-IPA solvent was 20% at a dosage of 17 mL of the solvent and a temperature of 30℃, the acid number of the refined diesel fraction was 0.015 mg KOH/g with a good stability of acidity in the diesel fraction,     

大位移井钻柱振动规律研究与应用

在大位移井钻井工程中钻柱受着各种振动，当各种振动共振时，钻柱承受着非常大的动载，很容易受损，同时，钻柱的振动影响着井壁的稳定，严重威胁着井下的作业安全。以大位移井近井底的钻柱为研究对象，分析了钻柱振动行为所遵循的规律。采用线性分析法，获得了大位移井钻柱横向振动和扭转振动的频谱方程。同时获得了钻柱各种共振频率的分布。经分析表明：大位移井钻柱的横向振动和扭转振动的共振频率与实际钻井转速非常接近，应合理选择转速以减小钻柱共振的发生。文章的分析研究为大位移井钻柱动态行为的研究提供了理论依据。     

A New Comb Circular Polarizer Suitable for Millimeter‐Band Application

This letter presents a new polarizer which has a simple comb structure inside a circular waveguide. The electrical performance of the proposed comb polarizer is optimized by a circular waveguide radius and by the physical parameters of the comb plates. This polarizer is suitable for providing good performance in millimeter‐band application because of its simple structure and low fabrication cost. In our experiments the dual‐band comb polarizer designed in band 1(K) and band 2(Ka) showed good electrical performance without any tuning elements.     

一种基于ECDSA的USB存储设备访问控制方案

文章针对使用USB存储设备造成的内部泄密问题,提出了一种USB存储设备访问控制方案,该方案对用户的身份认证基于安全强度很高的椭圆曲线数字签名算法,同时使用过滤器驱动程序实现了USB存储设备的读写控制,因而此方案具有较好的安全性、实用性和通用性。     

A high-performance multichannel dual-gate poly-Si TFT fabricated by excimer laser irradiation on a floating a-Si thin film

A new excimer laser annealing (ELA) process that uses a floating amorphous-Silicon (a-Si) thin film with a multichannel structure is proposed for high-performance poly-Si thin-film transistors (TFTs). The proposed ELA method produces two-dimensional (2-D) grain growth, which can result in a high-quality grain structure. The dual-gate structure was employed to eliminate the grain boundaries perpendicular to the current flow in the channel. A multichannel structure was adapted in order to arrange the grain boundary to be parallel to the current flow. The proposed poly-Si TFT exhibits high-performance electrical characteristics, which are a high mobility of 504 cm/sup 2//Vsec and a low subthreshold slope of 0.337 V/dec.     

Development of a safety critical software requirements verification method with combined CPN and PVS: a nuclear power plant protection system application

Safety-critical software systems such as certain nuclear instrumentation and control (NI&C) systems should be developed with thorough verification. This study presents a method of software requirement verification with a case study for a nuclear power plant (NPP) protection system. The verification introduces colored petri net (CPN) for system modeling and prototype verification system (PVS) for mathematical verification. In order to aid flow-through from modeling by CPN to mathematical proof by PVS, an information extractor from CPN models has been developed in this paper. In order to convert the extracted information to the PVS specification language, a translator has also been developed. This combined method has been applied to the functional requirements of the Wolsong NPP Shut Down System #2 (SDS2); logical properties of the requirements were verified. Through this research, guidelines and a tool support for the use of formal methods have been developed for application to NI&C software verification.     

Development of core mode blocker with H/sub 2/-loaded Ge-B codoped fibres

A novel fabrication method of the core mode blocker by exposing H/sub 2/-loaded Ge-B codoped fibres to local electric arc discharge for application to the LPFGs-based tunable all-fibre bandpass filter with 6.5 nm bandwidth and 40 nm tuning range is presented.     

改性乳化沥青的发展和应用概况

综述了改性乳化沥青的发展及应用概况,重点讨论了改性乳化沥青的生产、制备工艺、稳定性影响因素,并对国内外改性乳化沥青的应用情况加以概述。     

Thermomechanical finite-element model of shell behavior in continuous casting of steel

A coupled finite-element model, CON2D, has been developed to simulate temperature, stress, and shape development during the continuous casting of steel, both in and below the mold. The model simulates a transverse section of the strand in generalized plane strain as it moves down at the casting speed. It includes the effects of heat conduction, solidification, nonuniform superheat dissipation due to turbulent fluid flow, mutual dependence of the heat transfer and shrinkage on the size of the interfacial gap, the taper of the mold wall, and the thermal distortion of the mold. The stress model features an elastic-viscoplastic creep constitutive equation that accounts for the different responses of the liquid, semisolid, delta-ferrite, and austenite phases. Functions depending on temperature and composition are employed for properties such as thermal linear expansion. A contact algorithm is used to prevent penetration of the shell into the mold wall due to the internal liquid pressure. An efficient two-step algorithm is used to integrate these highly nonlinear equations. The model is validated with an analytical solution for both temperature and stress in a solidifying slab. It is applied to simulate continuous casting of a 120 mm billet and compares favorably with plant measurements of mold wall temperature, total heat removal, and shell thickness, including thinning of the corner. The model is ready to investigate issues in continuous casting such as mold taper optimization, minimum shell thickness to avoid breakouts, and maximum casting speed to avoid hot-tear crack formation due to submold bulging.