Failure Analysis of AISI 440C Steel Ball Screws Used in the Actuator System of a Satellite Launch Vehicle

In view of its excellent wear and corrosion resistance, AISI 440C steel is the material of choice for the fabrication of ball screws used in actuator systems of satellite launch vehicles. During the routine acceptance test of a ball screw, longitudinal cracks were observed at the shaft location of the ball screw. The optical microstructure of the ball screw material (AISI 440C) revealed the presence of aligned carbides (carbide banding). Fractographic observations revealed the cracking to be along the carbide bands. Based on detailed optical and scanning electron microscopic observations, the cracking of the ball screws was attributed to the carbide bands.     

Frequency dependent electrical transport properties of 4,4′,4″-tris(N-3-methylphenyl-N-phenylamine)triphenylamine by impedance spectroscopy

The frequency dependent ac conduction mechanism in 4,4′,4″-tris(N-3-methylphenyl-N-phenylamine)triphenylamine (m-MTDATA) has been studied as a function of applied bias and temperature. The Cole–Cole plot shows a slightly depressed semicircle indicating Debye type relaxation. This result has been explained by an equivalent circuit of the device designed as a two parallel resistor and capacitance network in series with contact resistance. The ac conduction studies under dc bias for hole only devices shows an increase in device conductivity with the increase in bias. The variation of bulk resistance with applied bias indicates Space Charge Limited Conduction (SCLC) mechanism for hole conduction. The hole mobility of the material has also been evaluated from SCLC as 8.859 × 10^?6 cm²/V s. The temperature dependent impedance studies show two activation energies indicating two different phase of the material with a phase transition at 235 K.     

Evidence of low-symmetry phases in pressure-dependent Raman spectroscopic study of BaTiO<Subscript>3</Subscript>

In the earlier pressure-dependent Raman spectroscopic studies, it has been reported that BaTiO₃ undergoes a tetragonal to cubic phase transition above ~ 2 GPa, whereas pressure-dependent X-ray absorption, X-ray diffuse scattering studies and pair distribution function studies have reported the presence of a low-symmetry rhombohedral phase above ~ 2.3 GPa. In this report, we present our pressure-dependent Raman spectroscopic studies on polycrystalline BaTiO₃ which shows that it first undergoes a transition from tetragonal to orthorhombic/rhombohedral phase above ~ 2.6 GPa and then finally goes to the cubic phase above 8.4 GPa. Pressure-dependent synchrotron X-ray diffraction (SXRD) studies have also been carried out that provided rate of change of volume as a function of pressure resulting in bulk modulus of 215 ± 9 GPa.     

Geometric optimization of trapezoidal thermoelectric heat pump considering contact resistances through genetic algorithm

An alternate option for improving the performance of the thermoelectric heat pump (TEHP) is the variation in thermoelectric leg configuration. In this paper, the thermodynamic model based on first and second law of thermodynamics for an exoreversible TEHP including influence of Thomson effect as well as leg geometry on the coefficient of performance and heating load of the device has been developed and optimized. Modified expressions have been derived analytically for dimensionless heating load, irreversibilities, figure of merit, energy, and exergy efficiency. The effects of operating and geometry parameters such as shape parameter (A_c/A_h), temperature ratio (T_c/T_h), Thomson effect, thermal and electrical contact resistances on the coefficient of performance, and heating load of the TEHP have been analysed. The results indicate that the Thomson effect has adverse effect on heating load of the system. The optimal parameters obtained through GA optimization process have been compared with the optimal parameters obtained through analytical method which proved the validity of GA optimization method for optimization of TEHP. After the testing, the GA optimization has been performed to determine the optimum parameters corresponding to maximum energy efficiency and maximum heating load. It was found that the GA population converges quickly after 20 runs only which proved the GA as time and cost‐effective optimization tool. This study will be useful for designing of practical TEHP systems of different leg geometries.     

Preparation, thermal expansion, high pressure and high temperature behavior of Al2(WO4)3

The titled compound Al₂(WO₄)₃ was synthesized by a conventional solid state reaction and characterized by powder XRD. It crystallizes in an orthorhombic (Pbcn, No. 60) lattice, with unit cell parameters as 12.582(2), 9.051(1), 9.128(2) Å, and V = 1039.5(3) (Å)³. The compound was found to show negative thermal expansion (NTE) behavior in the temperature range of 25 to 850°C. The average linear NTE coefficient (₁), in this temperature range, was –1.5 × 10^–6 K^–1. The effect of pressure at ambient temperature, was studied by a Bridgman Anvil (BA) apparatus, to reveal that there is no irreversible phase transition up to 8 GPa. The effect of high pressure and high temperature on this compound was studied by a Toroid Anvil (TA) apparatus. This compound has a limited stability under high pressure and temperature, as it undergoes a decomposition to AlWO₄ and WO_3–x with a partial oxygen loss. As an off-shoot of this work, certain new modifications of WO_3–x under pressure and temperature were observed, viz., monoclinic, tetragonal and an orthorhombic modifications at 5 GPa/1400°C, 3 GPa/900°C and 1.8 GPa/1030°C, respectively. The detailed XRD studies of the products are presented here.     

Effect of surface recombination on the transient decay of excess carriers produced by short wavelength laser pulses

Effect of surface recombination on the transient decay of excess carriers injected very near to the surface region has been analysed for a semi-infinite semiconductor sample. The one dimensional continuity equation for the excess minority carriers has been solved analytically assuming that the surface recombination is important only on the front surface from which the excess carriers are injected. The decay of total excess carrier charge as a function of time is calculated for various values of the surface recombination velocities. It is found that values of S lower than 10³ cm/sec. have little effect on the decay of total excess charge and the decay is exponential. For values of S larger than 10⁴ cm/sec. the initial decay of excess charge is much faster and is dominated by the surface recombination. However, if one waits long enough for the excess carrier to diffuse into the semiconductor the decay becomes exponential when the excess charge decays to about 5% of its initial value. This exponential decay can be used to determine the excess carrier lifetime fairly accurately. A source of error in such experiments may arise from the heating of the silicon sample by the laser pulse. This effect, however is negligible for short duration pulses of low average power.     

The Future of Mental Health.

Examines the two sets of criteria that generally categorize mental health: those that emphasize internal events and those that deal with external events. The author discusses the future of mental health in light of many of its current trends, including greater acceptance of diversity, and he discusses the potential future role of the mental health professional. The author notes that greater numbers of mental health professionals have gotten involved with different populations, and suggests that the majority of mental health professionals will probably be experts in handling small units of behavior or experience for a limited time. The very process of making predictions changes the future course of events. Let us hope that this intricate process will result in greater satisfaction for greater numbers of people. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Wastewater treatment sludge as a raw material for the production of Bacillus thuringiensis based biopesticides

Seven wastewater sludges of different origins and types were used as an alternate culture medium for producing Bacillus thuringiensis variety kurstaki HD-1. The sludge samples were used under three different preparations: without pre-treatment, with acid treatment (hydrolysed sludge) and the supernatant obtained after centrifugation of the hydrolysed sludge. The sludge composition varied widely with origin and the type of sludge. Growth and sporulation were evaluated by the total viable cell count and spore count of the preparations. Growth, sporulation and endotoxin production were affected by the sludge origin. Hydrolysed sludge gave the highest viable cell and spore counts while the liquid phase (supernatant) gave the lowest. Non-hydrolysed primary sludge from Valcartier was unable to sustain bacterial growth because of its low pH. Bioassays were conducted against larvae of spruce budworm to evaluate entomotoxic potential of the preparations obtained. In general, sludge hydrolysis increased the entomotoxicity yields. Similar entomotoxicity was observed in Black Lake secondary sludge (4100 IU/microL) as that obtained in the reference soya medium (3800 IU/microL). The use of the sludge supernatant (liquid phase) was not recommended due to the low entomotoxic potential obtained.     

Photoconduction investigations in 75 MeV oxygen ion irradiated kapton-H polyimide

Photoconduction behaviour of 75 MeV oxygen ion irradiated (Fluences: 1.8 × 10¹¹, 1.8 × 10¹² and 1.8 × 10¹³ ions/cm²) kapton-H polyimide film in the visible region has been investigated at different temperatures ranging 400-2500 °C and at various electric fields ranging 40-600 kV/cm. A photoinduced exciton formation is the major source for providing charge carriers through thermolization and field-assisted dissociation processes. An attempt has been made to fit the field dependence of the steady state photocurrent to one of the several possible conduction mechanisms. In the high and low fluence (1.8 × 10¹³ and 1.8 × 10¹¹ ions/cm²) irradiated samples there exists a possibility of Poole-Frankel type of photoconduction mechanism, whereas at intermediate fluence (1.8 × 10¹² ions/cm²) a Schottky type photoconduction mechanism may be operative. The log I_ps versus 1/T plots consist of two straight lines with a knee point around 800-1000 °C. The activation energy estimated from the slope of these lines is field dependent varying from 0.40 to 0.73 eV and 0.18 to 0.23 eV above and below the knee point, respectively. This indicates the presence of more than one type of trapping levels in irradiated kapton-H polyimide.     

In situ synthesised TiO2 ‐chitosan‐chondroitin 4–sulphate nanocomposites for bone implant applications

The artificial materials for bone implant applications are gaining more importance in the recent years. The series titania‐chitosan‐chondroitin 4–sulphate nanocomposites of three different concentrations (2:1:x, where x ‐ 0.125, 0.25, 0.5) have been synthesised by in situ sol–gel method and characterised by various techniques. The particle size of the nanocomposites ranges from 30–50 nm. The bioactivity, swelling nature, and the antimicrobial nature of the nanocomposites were investigated. The swelling ability and bioactivity of the composites is significantly greater and they possess high zone of inhibition against the microorganisms such as Staphylococcus aureus and Escherichia coli. The cell viability of the nanocomposites were evaluated by using MG‐63 and observed the composites possess high cell viability at low concentration. The excellent bioactivity and biocompatibility makes these nanocomposites a promising biomaterial for bone implant applications.Inspec keywords: titanium compounds, filled polymers, nanocomposites, bone, orthopaedics, biomedical materials, sol‐gel processing, nanofabrication, particle size, swelling, microorganisms, cellular biophysics, nanomedicine, prostheticsOther keywords: in situ synthesised TiO₂ ‐chitosan‐chondroitin 4‐sulphate nanocomposites, bone implant applications, artificial materials, in situ sol‐gel method, particle size, swelling nature, antimicrobial nature, microorganisms, Staphylococcus aureus, Escherichia coli, cell viability, MG‐63, biomaterial, size 30 nm to 50 nm, TiO₂