Nanoparticle formation in H2O/N2 and H2O/Ar mixtures under irradiation by 20 MeV protons and positive corona discharge

To investigate the contribution of ions to gas nucleation, we have performed experiments on the formation of water droplets in H₂O/N₂ and H₂O/Ar gas mixtures by irradiation with a 20 MeV proton beam and by positive corona discharge. The size of the formed nanoparticles was measured using a differential mobility analyzer equipped with a Faraday cup electrometer. Using the proton beam, droplets around 10 nm in diameter were observed for both positively and negatively charged particles, but none were found when the corona discharge was used. This implies the importance of the presence of both positive and negative ions for the formation of nanosize droplets, which attract each other by Coulomb interactions, enhancing the collision frequency and leading to the formation of the 10 nm droplets.     

Effect of Support Materials on the Selective Methanation of CO over Ru Catalysts

Selective methanation of CO in the reformate gas (CO/CO₂/H₂/H₂O = 0.175/17.9/70.9/11.1) proceeded over Ru catalysts supported on metal oxides and zeolites. CO was selectively methanated at wide temperature ranges (200–275 °C) over Ru/γ-Al₂O₃, Ru/TiO₂ Ru/H-Y and Ru/H-beta catalysts. Higher Ru contents in Ru/γ-Al₂O₃ improved the selective CO methanation rate.     

Impact of fertilizer on a small watershed of Lake Biwa: use of sulfur and strontium isotopes in environmental diagnosis

Sulfur and strontium isotopes (delta(34)S and (87)Sr/(86)Sr) were determined in 39 river water samples collected over three different cultivation periods (April, May, and June), and in several materials used for comparison (fertilizers, detergents, soils, irrigation and agricultural waters), to evaluate the impact of fertilizers on a small agricultural watershed of Lake Biwa, in central Japan. delta(34)S values in river water decreased (from +5.8 to -2.0 per thousand) with increasing SO(4) concentrations (3.8 to 93.2 ppm) from upstream to downstream of the watershed. Comparison of river water S isotopes with those of possible source materials indicates that the enrichment of SO(4) can be attributed to the dissolution of two kinds of fertilizers: (1) compound fertilizers commonly used in this area and (2) ammonium sulfate which is applied on a small scale. In contrast, (87)Sr/(86)Sr values of river water decreased with time from April (avg. 0.71163), through May (avg. 0.71139), to June (avg. 0.71127). The tendency of the sample plots on the (87)Sr/(86)Sr vs. 1/Sr diagram suggests a time-dependent increase in the contribution of soil water to the river, which is partly affected by the Sr-bearing fertilizers. It is suggested that a maximum of 25% of dissolved Sr is derived from these fertilizers, while more than 75% of it is of rock origin. Mass balance calculations permitted us to evaluate the proportion of fertilizer contribution in each river. Combined use of S and Sr isotopes together with concentration data could be a new environmental diagnosis technique for rivers and soils in localized watersheds.     

The growth of carbon coating layers on iron particles and the effect of alloying the iron with silicon

Magnetic fine particles of metallic Fe coated with graphitic carbon layers were synthesized by annealing Fe₂O₃ particles with carbon powders at 1673 K in nitrogen atmosphere. For comparison, SiC was added to Fe₂O₃. X-ray diffraction measurement showed that the lattice constants of Fe changed depending on the Si contents. Mössbauer spectroscopy confirmed that Fe-Si alloys were formed by the Si addition and that the iron carbide disappeared. Electron microscope images revealed that the thickness of carbon coating layers increased from 24 nm to 36 nm as a result of the Si addition. Soaking tests showed that the corrosion resistance of the carbon-coated Fe particles was improved by the addition of Si. The results suggest that Si caused C to leave the Fe cores and move to the surface to form a carbon coating.     

Formation of a Third Liquid Phase and Its Reuse for Dibenzyl Ether Synthesis in a Tetraalkylammonium Salt Phase Transfer Catalytic System

This paper describes the formation of a third liquid phase in a phase transfer catalytic system in the presence of benzyl alcohol and potassium hydroxide, where dodecane and tetraalkylammonium bromide serve as organic solvent and catalyst, respectively. In this kind of system, a symmetrical ether (dibenzyl ether) was synthesized from benzyl chloride and benzyl alcohol at 323 K. In particular, the investigation demonstrates that the observed reaction rate constant depends on the length of the alkyl group of the catalyst. Tetrabutylammonium bromide exhibits the highest catalytic activity among the catalysts explored. With respect to the reuse of the third liquid phase, the results confirm that there is no decrease in phase transfer catalytic activity in three consecutive runs.     

Heteroepitaxial growth of Zn1−xCdxSe on cleavage-induced GaAs (110) surface in ultra high vacuum

Zn_1−xCd_xSe epitaxial growth by molecular beam epitaxy (MBE) on the GaAs (110) surface cleaved in ultra high vacuum (UHV) was investigated. The growth mode of Zn_1−x Cd_xSe on GaAs (110) was not a simple Stranski–Krastanow type. At initial growth stage, growth mode was two-dimensional type. However, as the growth proceeds three-dimensional island growth and two-dimensional growth modes compete. As a result, two kinds of structures were spontaneously formed on the surface, pyramidal-shaped islands and ridge structures aligned to the [1 0] direction. Anisotropic in-plane strain relaxation on (110) is suggested as the formation mechanism of such structures.     

Introduction to the Journal on Digital Libraries special issue on Asian digital libraries

International Journal on Digital Libraries -     

EPR study of the electronic states of β′-(BEDT-TTF)(TCNQ)

β′-(BEDT-TTF)(TCNQ) is a compound of BEDT-TTF (=ET) and TCNQ molecules aligned orthogonally with each other, forming two-dimensional sheets and one-dimensional columns of 1/4-filled π band, respectively. It is known that the metal-insulator transition occurs at 330 K at ambient pressure. We have measured the electronic spin susceptibility by means of the EPR-NMR method at 50 MHz, and the angular dependence of g-factor and line width of EPR both at Q (34 GHz) and W (94 GHz) band. We successfully confirmed that the antiferromagnetic transition occurs in ET sheets and TCNQ columns, independently.     

A New Approach to Humanitarian Demining

Humanitarian demining is an application in which the use of tele-operated machines and mechanisms has been gaining acceptance recently. Actually, demining is just one among many other field applications that require a high degree of mobility, manipulation of loads, robustness and, above all, high efficiency in terms of energy consumption. This paper will present the development and analysis of Field Arm, a pantographic manipulator especially designed for field works, focusing on its kinematic, static and dynamic properties. The novel features of Field Arm will be presented and discussed with results of simulations and experiments.     

An analytical and numerical study of coupled transient natural convection and solidification in a rectangular enclosure

The transient process of the solidification of a pure liquid phase-change material in the presence of natural convection in a rectangular enclosure is considered both analytically and numerically. One vertical boundary is held at a temperature below the melting-point of the material, the other above; the horizontal boundaries are both assumed adiabatic. A nondimensional analysis of the problem, principally in terms of the Rayleigh (Ra) and Stefan (St) numbers, indicates that some asymptotic simplification is possible for materials often considered in the literature (water, gallium, lauric acid). This observation suggests a way to simplify the full problem when Ra  1 and St  1, giving a conventional boundary value problem for the liquid phase and pointwise-in-space first-order ODEs for the evolution in time of the solidification front. The method is tested against full 2D finite-element-based transient numerical simulations of solidification. In addition, simpler approaches for determining the average thickness of the solid layer, based on boundary-layer and enclosure flow correlations, are also investigated.