Observations of vibration shape of AT-cut quartz resonator including electric twins

Quartz crystal resonators, including electric twins, are investigated. Electric twins are artificially formed in the usual AT-cut quartz crystal resonantor before the deposition of electrodes. We have directly observed that vibrations generated at electrodes propagate into the outside region isotropically, but cannot propagate into the region of electric twin.     

Automated detection of pulmonary nodules in helical CT images based on an improved template-matching technique

The purpose of this study is to develop a technique for computer-aided diagnosis (CAD) systems to detect lung nodules in helical X-ray pulmonary computed tomography CT) images. We propose a novel template-matching technique based on a genetic algorithm (GA) template matching (GATM) for detecting nodules existing within the lung area; the GA was used to determine the target position in the observed image efficiently and to select an adequate template image from several reference patterns for quick template matching. In addition, a conventional template matching was employed to detect nodules existing on the lung wall area, lung wall template matching (LWTM), where semicircular models were used as reference patterns; the semicircular models were rotated according to the angle of the target point on the contour of the lung wall. After initial detecting candidates using the two template-matching methods, we extracted a total of 13 feature values and used them to eliminate false-positive findings. Twenty clinical cases involving a total of 557 sectional images were used in this study. 71 nodules out of 98 were correctly detected by our scheme (i.e., a detection rate of about 72%), with the number of false positives at approximately 1.1/sectional image. Our present results show that our scheme can be regarded as a technique for CAD systems to detect nodules in helical CT pulmonary images.     

Fine silicon carbide fibers synthesized from polycarbosilane-polyvinylsilane polymer blend using electron beam curing

A fine SiC fiber is synthesized from a polymer blend of polycarbosilane (PCS) and polyvinylsilane (PVS) with electron beam curing under vacuum. The obtained SiC fiber from the PCS-PVS blend polymer has smaller average diameter of 8.5 m than that of 11.8 m from PCS, and shows higher average tensile strength of 3.2 GPa than that of 2.8 GPa from PCS after heat treatment at 1673 K in Ar gas atmosphere. However, the SiC fiber from the polymer blend decreases in tensile strength after heat treatment above 1773 K due to -SiC crystal growth near the fiber surface, because of a small amount of oxygen incorporated in the fiber.     

Disintegration process of yttria-stabilized zirconia ceramics using hydrothermal conditions

Capability of the recycling of high strength and high fracture toughness yttria-stabilized tetragonal zirconia polycrystalline (Y-TZP) sintered body utilizing “low-temperature annealing degradation” phenomenon was investigated. Hydrothermal treatment was employed to induce the phase transformation from tetragonal to monoclinic zirconia and to disintegrate the Y-TZP sintered body. 3 mol% Y₂O₃–ZrO₂ specimens sintered at 1,550 °C and more were disintegrated without leaving the original appearances when the treatment temperature was between 200 °C and 400 °C. The size of the disintegrated fragments of Y-TZP sintered body was much affected by hydrothermal treatment conditions. Only with hydrothermal treatment and simple ball milling, the sintered body was pulverized into the primary particle level. This technique is expected to apply to a sustainable recycling system for the zirconia ceramics, which restrains an energy consumption compared to crushing zirconia using mechanical procedures.     

An Improvement Method of Matrix Converter Drives Under Input Voltage Disturbances

While the matrix converter has many advantages that include bidirectional power flow, a size reduction, a long lifetime, and sinusoidal input currents, it is vulnerable to the input voltage disturbances, because it directly exchanges the input voltage to the output voltage. The instantaneous effective power control (IEPC) method has been proposed to compensate the input voltage disturbances, in which the instantaneous effective power is kept constant by controlling input current. However, to date, no method has been proposed to maintain the stability of the system with the IEPC. The purpose of this paper is to propose a method to control the stability of the system with IEPC. First, this paper explains the IEPC theoretically. Next, a model of the system with the IEPC is developed, and stability analyses are conducted. Then, based on the results of the analyses, a stability control method for the system with the IEPC is proposed. Furthermore, the validities of the proposed method are demonstrated by simulation and experiments. Finally, a restart performance of the system after momentary power interruption is discussed. Because the IEPC does not need phase-locked-loop to detect the phase angle of the input voltage, fast restart is expected     

Low-Force Electric Contact Processes on Cu Electrodes

A contact process between large-scale integration (LSI) pads and test probes at low contact force is a key to developing a probe card with smaller pitch and higher pin count. In this paper, we report on the characteristics of low-force contact methods on Cu electrodes. One is the fritting process, in which an electric breakdown is utilized to break the surface oxide, and the other is the heating treatment in hydrogen gas aimed at deoxidizing the surface Cu oxide. Conventional tungsten needle probes were used as testing probes, and contact resistances at low contact force of 1-5 mN were measured. Contact resistances smaller than 1 Omega were obtained by the fritting processes, in which the voltage and the current were 10 V and 280-320 mA, respectively. A deoxidization process at over 260degC was found to be effective for decreasing the contact resistance. The X-ray photoelectron spectroscopy (XPS) was utilized to investigate the surface state of hydrogen-treated Cu, and the deoxidization of Cu₂O to Cu was observed in samples treated at 260degC, while no change was found in that at 150degC.     

Numerical analysis method for the RC and geological structures subjected to extreme loading by energetic materials

This paper proposes and demonstrates a numerical simulation method suitable to analyze the local damage and dynamic response of the structures composed of the reinforced concrete (RC) and/or the geological materials subjected to extremely severe loading by the energetic material like high explosives (HE).     

Usefulness of Permanent Power Fuse in Control Centers with Molded Case Circuit Breakers

The increase in electric power consumption in industry has led to the development of modern distribution systems such as control centers having high kVA ratings and high prospective fault current. In such a situation, the improvement of the system usefulness such as reliability and cost effectiveness is the essential requirement. An index is presented to evaluate the system usefulness using the cost effectiveness for fault protection in a system of given bank kVA. The index is estimated on four different system structures of control centers, including one which utilizes Permanent Power Fuses (PPF). It is presented that the PPF combined with molded case circuit breaker in main circuit effectively improves the cost effectiveness in control centers with high fault current. Operating principles of the PPF and the control center utilizing the PPF are briefly outlined.     

Design principle of micromechanical probe with an electrostatic actuator for friction force microscopy

It is important to understand friction force in micro/nano mechanical devices both at high sliding speed and with high lateral resolution. Dual-axis friction force microscopes that can provide high lateral resolution and accuracy have been proposed; however, the sliding speed is limited by the probe scan speed. While a micro mechanical probe (MMP) with an electrostatic actuator can overcome this problem, details of probe design have not been established yet. This paper presents the principle of the mechanical design for an MMP with high force sensitivity and sufficient drive force. The dimensions of the double cantilever beam control the spring constants, resonant frequencies, and drive force. The use of an actuated MMP enables accurate friction force microscopy at high sliding speeds, which is required for the design of micro/nano mechanical devices.     

Passive piezoelectric single-side MEMS DC current sensor with five parallel PZT plates applicable to two-wire DC electric appliances without using cord separator

A passive (power-less), non-contact macro-scale piezoelectric bimorph DC current sensor to satisfy the increasing needs of DC power supply for monitoring the electricity consumption by either one-wire or two-wire appliance cord was proposed at our laboratory previously. In present study however, a MEMS-scale piezoelectric single-side DC current sensor, comprised of five parallel PZT plates, was further proposed and micro-fabricated for preliminarily examination. A micro magnet was fixed by manipulator onto the PZT cantilever tip to the theoretically pinpointed position of the center plate. Different from the results of the macro-scale piezoelectric bimorph DC current sensor, impulsive piezoelectric output voltages accompanying with a gradual decrease in decay were detected when the applied DC electric current was varied from 0.5 to 2.5 A. A linear relationship between the detected peak value of the impulse output voltage and the applied DC electric current was also obtained but with a higher slope compared to the result of the macro-scale piezoelectric bimorph DC current sensor.