Effects of ion group content and polyol molecular weight on physical properties of HTPB‐based waterborne poly(urethane‐urea)s

A series of waterborne poly(urethane‐urea)s, WPUUs, based on using nonpolar hydroxyl‐terminated polybutadiene (HTPB) as the soft segment, were successfully synthesized in this article. The effects of the COOH group content and soft‐segment molecular weight (Mn_s) on the dispersion, morphology, and physical properties were investigated. Variations of the particle size, viscosity, and zeta potential were first governed by the hydrophilicity of the polymer chain, and then by the swelling derived from water. Fourier transfer infrared spectroscopy (FTIR) and differential scanning calorimetry (DSC) indicated that the degree of phase separation decreased as the COOH group content increased or as Mn_s decreased. However, the hydrogen bonding between the soft and hard segments and the two‐phase mixing could not occur in this nonpolar HTPB‐based WPUU system, indicating that the hard segments tended to form smaller domains and to pack more loosely. It was attributed to the fact that the presence of bulky ionic salt groups destroyed the ordered arrangement of the hard segments. In this case, the increases of the interface area between the soft and hard phases resulted in that the present behaviors were similar to the phase mixing. In tensile properties, HTPB‐based WPUUs exhibited higher tensile stress, elongation at break, and modulus as the COOH group content decreased or as Mn_s decreased. In thermal degradation, the introduction of HTPB polyol improved the thermal stability of WPUU. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Migration of Intergranular Liquid Films and Formation of Core-Shell Grains in Sintered TiC–Ni Bonded to WC–Ni

When TiC–20 wt% Ni powder mixtures are sintered at 1400°C, relatively large TiC grains possibly containing some Ni form with near-equilibrium shapes. When these specimens are heat-treated again at 1400°C in contact with sintered WC–20 wt% Ni pieces, the liquid films between the TiC grains in the contact region migrate against their increasing curvatures, forming (Ti,W)C solid solution behind them. These migrating liquid films reverse their directions on further heat-treatment. As in other alloys, this liquid film migration must be driven by the coherency strain energy produced by W diffusion at the surface of the dissolving TiC grains. Shells of (Ti,W)C solid solution also form around the cores of TiC grains near the contact region, and this process is probably driven by both coherency strain energy and free energy of mixing. At some contact regions, (Ti,W)C precipitates nucleate and grow, probably driven mainly by the free energy of mixing. In powder mixtures, the formation of core-shell grains is expected to be driven by the coherency strain energy, the free energy of mixing, and the capillary effect.     

Modification of a carbon/carbon composite with a thermosetting resin precursor as a matrix by the addition of carbon black

Carbon/carbon composites were made through the pyrolysis of stabilized PAN felt and phenolic resin with the addition of 5 or 10 wt % carbon black to the matrix and then heat treatment at 600–2500°C. The effects of adding carbon black to the matrix precursor on the physical properties, microstructure, and mechanical properties of the resultant composites were investigated. Adding carbon black not only reduced the weight loss but also limited the shrinkage of the resultant composites. Adding carbon black also accelerated the formation of carbon basal planes in the matrix. At 2500°C, the crystalline stacking height in the composite with 10 wt % added carbon black was 200% greater than that with no additive. The flexural strength of the composite also increased from 15 to 42 MPa (almost 300%). © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 333–337, 2006     

Influence of continuous stabilization on the physical properties and microstructure of PAN-based carbon fibers

A continuous stabilization and carbonization process was used to prepare polyacrylonitrile (PAN)-based carbon fibers. The stepwise stabilization of PAN fibers was tried at various temperatures. The effect of stepwise stabilization on the physical properties and microstructure of the final carbon fibers is reported in this article. The fixed temperature in stepwise stabilization is kept below the fusion temperature of PAN precursors to avoid overstabilization of the fibers. The optimum stepwise stabilization process not only increases the amount of ladder polymer in stabilized fiber but also improves the physical and mechanical properties of the resultant carbon fibers. The formation of closed pores from open pores in carbon fiber occurs at 1100°C, but the formation of closed pores occurs at 200°C lower for carbon fiber developed from overstabilized fiber. The effect of continuous stepwise stabilization on the properties of resulting stabilized fibers and the variation in physical properties, element composition, and microstructure of carbon fibers during the carbonization process are also reported in this article.     

Activities of MFI-Supported Rhenium Catalysts for the Aromatization of Methane: Effect of Cationic Form of the Inorganic Carrier

MFI type inorganic carrier was used in two different cationic forms, hydrogen and calcium respectively. MFI-supported molybdenum and rhenium catalysts were prepared. The activities of the catalysts were compared for the aromatization reaction of methane. Higher activity values were attained with the catalysts supported on HZSM-5. Aromatics were also observed with the catalysts supported on CaZSM-5, despite their deficiency in acid sites. Highly dispersed rhenium is expected to be formed with the use of the inorganic carrier in calcium form. On the other hand, lower reaction rates were observed with rhenium supported on CaZSM-5, in spite of the improved dispersion of the active rhenium species on this catalyst. This was interpreted in terms of the critical role of the acid sites in the conversion of methane to aromatics, compared to the improved dispersion of the active metal.     

Degradation of 4-chloro-2-methylphenol in aqueous solution by electro-Fenton and photoelectro-Fenton processes

Degradation of 4-chloro-2-methylphenol (PCOC), a refractory toxic chemical emitted to the environment from the industrial production of phenoxy herbicides was studied in aqueous solution. Electro-Fenton and photoelectro-Fenton processes were used as the degradation methods. H₂O₂, produced by the reduction of oxygen at carbon cathode reacted with dissolved metal ions to form hydroxyl radicals, which in turn reacted with PCOC sequentially to degrade the aromatic ring. The effects of using different [Fe²⁺]/[PCOC]₀ and the effect of replacing Fe²⁺ by Mn²⁺ ion have been examined. It was found that degradation rate was increased with increasing [Fe²⁺]/[PCOC]₀ ratio from 2 to 4. However, the total charge utilized during the treatment was also increased. The efficiency of PCOC degradation was observed to be higher when Mn²⁺ was used as the catalyst. The mineralization of aqueous solutions of PCOC, withdrawn from the reactor at certain time interval, has been followed by total organic carbon (TOC) decay and dechlorination. A fast and complete degradation of the aromatic ring was achieved in photoelectro-Fenton system. 41.7% TOC decay and complete dechlorination were observed by consuming only 141.4 C electrical charge during a 300 min photoelectron-Fenton treatment. In the case of electro-Fenton system, 280.7 C electrical charge was consumed during 450 min of electrolysis to attain a similar degradation of PCOC. 14.9% TOC removal and 89.3% dechlorination have been obtained in this system under the applied conditions.     

Fabrication of SiO2-ZrO2 composite fiber mats via electrospinning

(1 − x)SiO₂-(x)ZrO₂ (x = 0.1, 0.2) composite fiber mats were prepared by electrospinning their sol-gel precursors of zirconium acetate and tetraethyl orthosilicate (TEOS) without using a polymer binder. The electrospun composite fibers were characterized by powder X-ray diffraction (XRD), scanning electron microscopy (SEM), fourier transform infrared spectroscopy (FT-IR) and mercury porosimetry. The composite fibers having a tetragonal crystalline ZrO₂ were obtained by calcining the electrospun composite fibers at high temperatures. The results show that the structure and crystallization of ZrO₂ in the composite fibers can be controlled by sintering temperature, while the porosity and morphology of the fiber mats did not depend on the sintering temperature.     

A web-based platform for biosignal visualization and annotation

With the advent of wearable sensing and mobile technologies, biosignals have seen an increasingly growing number of application areas, leading to the collection of large volumes of data. One of the difficulties in dealing with these data sets, and in the development of automated machine learning systems which use them as input, is the lack of reliable ground truth information. In this paper we present a new web-based platform for visualization, retrieval and annotation of biosignals by non-technical users, aimed at improving the process of ground truth collection for biomedical applications. Moreover, a novel extendable and scalable data representation model and persistency framework is presented. The results of the experimental evaluation with possible users has further confirmed the potential of the presented framework.     

Surface analysis and adsorption behavior of caffeine as an environmentally friendly corrosion inhibitor at the copper/aqueous chloride solution interface

Abstract

Corrosion inhibitors based on environmentally friendly and harmless products are currently being studied and developed. The corrosion inhibition properties of caffeine (1,3,7-trimethylxanthine) on copper corrosion in aqueous chloride solution (3.5?wt.% NaCl) are analysed here using stationary and transient electrochemical methods, and a theoretical study based on density functional theory is carried out. Caffeine is a very competitive compared to the chemical inhibitors that are often used for copper protection. Electrochemical and impedance experiments reveal that the protective efficiency of caffeine reaches a value of 96% at a concentration of 10^?2?mol L^?1. Based on these results, the Langmuir model appears to be the best representation of the adsorption of caffeine onto the copper surface. Scanning electron microscopy coupled with energy-dispersive X-ray spectroscopy and X-ray diffraction (XRD) were used to determine the surface morphology and the chemical composition of the copper surface in chloride media, in the absence and presence of caffeine. The results show the development of a mechanism of corrosion inhibition. In order to confirm the correlation between the inhibitory effect and the molecular structure of caffeine, quantum chemical parameters are used to calculate its electronic properties.     

Selective CO oxidation in the presence of hydrogen over supported Pt catalysts promoted with transition metals

Selective CO oxidation in the presence of excess hydrogen was studied over supported Pt catalysts promoted with various transition metal compounds such as Cr, Mn, Fe, Co, Ni, Cu, Zn, and Zr. CO chemisorption, XRD, TPR, and TPO were conducted to characterize active catalysts. Among them, Pt-Ni/γ-Al₂O₃ showed high CO conversions over wide reaction temperatures. For supported Pt-Ni catalysts, Alumina was superior to TiO₂ and ZrO₂ as a support. The catalytic activity at low temperatures increased with increasing the molar ratio of Ni/Pt. This accompanied the TPR peak shift to lower temperatures. The optimum molar ratio between Ni and Pt was determined to be 5. This Pt-Ni/γ A1₂O₃ showed no decrease in CO conversion and CO₂ selectivity for the selective CO oxidation in the presence of 2 vol% H₂O and 20 vol% CO₂. The bimetallic phase of Pt-Ni seems to give rise to stable activity with high CO₂ selectivity in selective oxidation of CO in H₂-rich stream.