Synthesis of ZSM‐5 Films and Monoliths with Bimodal Micro/Mesoscopic Structures

A route to synthesize ZSM‐5 crystals with a bimodal micro/mesoscopic pore system has been developed in this study; the successful incorporation of the mesopores within the ZSM‐5 structure was performed using tetrapropylammonium hydroxide (TPAOH)‐impregnated mesoporous materials containing carbon nanotubes in the pores, which were encapsulated in the ZSM‐5 crystals during a solid rearrangement process within the framework. Such mesoporous ZSM‐5 zeolites can be readily obtained as powders, thin films, or monoliths.     

Passive alignment method of polymer PLC devices by using a hot embossing technique

A novel fabrication process using a hot embossing technique has been developed for micromechanical passive alignment of polymer planar lightwave circuit (PLC) devices. With only one step of embossing, single-mode waveguide straight channels and micropedestals for passive aligning are simultaneously defined on a polymer thin film with an accuracy of /spl plusmn/0.5 /spl mu/m. This process reduces the steps for fabricating alignment structures. A fabricated polymer PLC chip and fibers are combined on a v-grooved silicon optical bench (SiOB) in a flip-chip manner. The process provides a coupling loss as low as 0.67 dB per coupling face and a cost-effective packaging solution for various polymer PLC devices.     

Hydrogen annealing effect on DC and low-frequency noise characteristics in CMOS FinFETs

The hydrogen annealing process has been used to improve surface roughness of the Si-fin in CMOS FinFETs for the first time. Hydrogen annealing was performed after Si-fin etch and before gate oxidation. As a result, increased saturation current with a lowered threshold voltage and a decreased low-frequency noise level over the entire range of drain current have been attained. The low-frequency noise characteristics indicate that the oxide trap density is reduced by a factor of 3 due to annealing. These results suggest that hydrogen annealing is very effective for improving device performance and for attaining a high-quality surface of the etched Si-fin.     

塔里木油田水碳酸盐平衡系数与有机酸的意义

根据统计学规律,对塔里木盆地油田水进行了研究,阐明了该盆地油田水的碳酸盐平衡系数(简称为R_C)与有机酸的基本特征。从油田水的无机组分与有机组分的统计分析中发现了油田水的碳酸盐平衡系数与有机酸存在明显的负相关性,进一步论证了碳酸盐平衡系数和有机酸与油气聚集及油气性质的关系。碳酸盐平衡系数越低及低碳有机酸的含量越高,它们与油藏,尤其是与 轻质油或气藏的关系越密切。从两者的关系中初步了解到有机酸的溶蚀作用对油气藏中储层次生孔隙的形成应有较重要的影响。     

Inside Front Cover: The Elastic Properties and Plastic Behavior of Two‐Dimensional Polymer Structures Fabricated by Laser Interference Lithography (Adv. Funct. Mater. 10/2006)

The probing of the micromechanical properties within a two‐dimensional polymer structure with sixfold symmetry fabricated via interference lithography reveals a nonuniform spatial distribution in the elastic modulus “imprinted” with an interference pattern in work reported by Tsukruk, Thomas, and co‐workers on p. 1324. The image prepared by M. Lemieux and T. Gorishnyy shows how the interference pattern is formed by three laser beams and is transferred to the solid polymer structure. The elastic and plastic properties within a two‐dimensional polymer (SU8) structure with sixfold symmetry fabricated via interference lithography are presented. There is a nonuniform spatial distribution in the elastic modulus, with a higher elastic modulus obtained for nodes (brightest regions in the laser interference pattern) and a lower elastic modulus for beams (darkest regions in the laser interference pattern) of the photopatterned films. We suggest that such a nonuniformity and unusual plastic behavior are related to the variable material properties “imprinted” by the interference pattern.     

InGaN microring light-emitting diodes

The fabrication and performance of an InGaN light-emitting diode (LED) array based on a microring device geometry is reported. This design has been adopted in order to increase the surface area for light extraction and to minimize losses due to internal reflections and reabsorption. Electrical characteristics of these devices are similar to those of a conventional large-area LED, while the directed light extraction proves to be superior. In fact, these devices are found to be more efficient when operated at higher currents. This may be attributed to improved heat sinking due to the large surface area to volume ratio. The potential applications of these devices are also discussed.     

温州市龙湾段标准堤工程软土地基变形原位观测

温州市龙湾段标准堤地基土中普遍存在一层海积淤泥,其强度低,压缩性高,承载力低,不能满足标准堤填筑及水闸运行的要求。采用预压法进行地基处理,取得的地基沉降、水平位移、孔隙水压力等现场观测资料,总结分析了该段海积淤泥地基的变形规律和特点。并提供了有关的原型观测数据,其沉降曲线规律性较好。     

Pyrolysis of Miscanthus Giganteus and wood pellets: TG-FTIR analysis and reaction kinetics

Characterisation of two biomass fuels (pelletised Miscanthus Giganteus and wood) was performed using thermogravimetric analysis with measurement of products by means of Fourier transform infrared spectroscopy (TG-FTIR). Three heating rate profiles were applied (10, 30 and 100 °C/min), with a final temperature of 900 °C. HCN and HNCO were found to be the major N-products, while the NH₃ fraction was detected to a minor extent. Kinetic parameters were obtained from the TG-FTIR results using a model based on parallel first-order reactions with a Gaussian distribution of activation energies. On the basis of the above kinetic analysis and product yields, input files for the functional group-devolatilisation, vaporisation, cross-linking biomass-pyrolysis model were prepared. The fit of model parameters to TG-FTIR product-evolution data was found to be generally good, but the model-predicted yields for some species did not fit experimental data at all heating rates. Further improvements in the model are needed to resolve above difficulty.     

Simultaneous amplification by Er ions and SRS in an Er-doped germano-silica fiber

A flat signal gain over in the entire C- and L-bands by erbium (Er) ions' radiative transition and stimulated Raman scattering in an Er-doped germano-silica fiber can be obtained if proper values of the concentration of Er and background loss in a fiber core are obtained during the fiber fabrication process. The optimized conditions for the flat C- and L-band gain are analyzed as functions of Er concentrations. Even for a low-gain value provided by a germano-silica core fiber with a low Er concentration and an optimum fiber length, a relatively low pump is required to obtain the flat gain band.