Measurement and numerical simulation of three‐dimensional fiber orientation states in injection‐molded short‐fiber‐reinforced plastics

To determine three‐dimensional fiber orientation states in injection‐molded short‐fiber composites, a confocal laser scanning microscope (CLSM) is used. Since the CLSM optically sections the specimen, more than two images of the cross sections on and below the surface of the composite can be obtained. Three‐dimensional fiber orientation states can be determined by using geometric parameters of fiber images obtained from two parallel cross sections. For experiments, carbon‐fiber‐reinforced polystyrene is examined by the CLSM and geometric parameters of fibers on each cross‐sectional plane are measured by an image analysis. In order to describe fiber orientation states compactly, orientation tensors are determined at different positions of the prepared specimen. Three‐dimensional orientation states are obtained without any difficulty by determining the out‐of‐plane angles utilizing fiber images on two parallel planes acquired by the CLSM. Orientation states are different at different positions and show the shell–core structure along the thickness of the specimen. Fiber orientation tensors are predicted by a numerical analysis and the numerically predicted orientation states show good agreement with measured ones. However, some differences are found at the end of cavity. They may result from the fountain flow effects, which are not considered in the numerical analysis. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 500–509, 2003     

Enhanced thermal stability of a sputtered titanium-nitride film as a diffusion barrier for capacitor-bottom electrodes

The effect of a thin RuO_x layer formed on the Ru/TiN/doped poly-Si/Si stack structure was compared with that on the RuO_x/TiN/doped poly-Si/Si stack structure over the post-deposition annealing temperature ranges of 450–600°C. The Ru/TiN/poly-Si/Si contact system exhibited linear behavior at forward bias with a small increase in the total resistance up to 600°C. The RuO_x/TiN/poly-Si/Si contact system exhibited nonlinear characteristics under forward bias at 450°C, which is attributed to no formation of a thin RuO_x layer at the RuO_x surface and porous-amorphous microstructure. In the former case, the addition of oxygen at the surface layer of the Ru film by pre-annealing leads to the formation of a thin RuO_x layer and chemically strong Ru-O bonds. This results from the retardation of oxygen diffusion caused by the discontinuity of diffusion paths. In particular, the RuO_x layer in a nonstoichiometric state is changed to the RuO₂-crystalline phase in a stoichiometric state after post-deposition annealing; this phase can act as an oxygen-capture layer. Therefore, it appears that the electrical properties of the Ru/TiN/poly-Si/Si contact system are better than those of the RuO_x/TiN/poly-Si/Si contact system.     

MEMS封装技术研究进展

介绍了MEMS封装技术的特点、材料以及新技术,包括单片全集成MEMS封装、多芯片组件(MCM)封装、倒装芯片封装、准密封封装和模块式MEMS封装等。文中还介绍了MEMS产品封装实例。     

600 A IGBT开关电路及其散热系统设计

采用IGBT开关电路，对大功率电阻带进行直流脉宽调制控制，实现了内燃机车大功率直流发电机负载实验中的负载大小的连续调节。为了避免在实验过程中IGBT器件的温度过高，采用独特的双管IGBT结构和双向强迫风冷的散热系统。实验表明该电路运行稳定、可靠。     

车古201潜山油藏完井方式研究

研究了国内外潜山油藏完井方式应用及其使用条件、井身结构的应用 ,针对车古 2 0 1油藏特点 ,论证了其对裸眼完井、筛管完井、尾管射孔完井、管外封隔器完井的适应性 ,通过对比研究 ,从更好地满足油藏工程、采油工艺、增产措施出发 ,选择出车古 2 0 1潜山油藏最合理的完井方式为尾管注水泥射孔完井 ,并给出了应采用的井身结构     

CL－1型缓蚀剂的研制

为了阻缓高含水原油对集输管线的腐蚀，研制了ＣＬ－１型输油管线缓蚀剂。这种缓蚀剂是以两种咪唑啉衍生物与联氨为主要成分的复配药剂，运用于油水共在体系．本文介绍了该剂的室内性能评价和现场试验结果。     

Quantitative analysis of ephedrines in urine by HPLC

Simultaneous determination of six ephedrines in urine sample has been achieved by high performance liquid chromatography on a Lichrospher RP-18 column, using methylamphetamine as internal standard. The 6 ephedrines are well separated in 25 minutes with resolution better than 1.8. This method has high recovery, selectivity and reproducibility, and the linearity is satisfactory from 1.5 micrograms/ml to 25 micrograms/ml with correlation coefficients better than 0.999.     

Boole函数的线性可分性(Ⅰ)——n-维超立方体的基本理论

Boole函数的线性可分性是前向人工神经网络理论中的一个比较困难的问题之一。目前仅对变量数n≤7的某些问题给予讨论。当n≥8时,尚无判别Boole函数线性可分的一般准则,更无线性可分Boole函数的计数公式。基于此,本文详细地研究了与Boole函数线性可分性有关的n-维超立方体的基本理论,包括n-维超立方体的基本性质、超立方体中的平行线、子超立方体的计数等,并给出了构造n-维超立方体图的一种新方法。     

具有阻力特性材料的σ_f－σ关系及一种新的阻力曲线测定方法

通过对相变增韧陶瓷及一种可切削玻璃－陶瓷动态疲劳（恒应力速率）试验中高应力速率区断裂应力下降现象的理论分析，发现这种现象与材料的阻力特性（Ｒ－ｃｕｒｖｅ）密切相关。确立的σ_ｆ－σ理论关系能够很好地描述整个应力速率区间内的动态疲劳试验结果。高应力速率区σ_ｆ－σ在双对数坐标下为负斜率直线，直线斜率为（ｍ为阻力曲线ＫＲ＝ｋ（△ａ）~ｍ的指数），断裂主要由材料阻力行为控制；低应力速率区，σ_ｆ－σ在双对数坐标下为正斜率直线，直线斜率为　（ｎ为应力腐蚀指数），断裂主要由材料应力腐蚀行为控制。建立了测定材料阻力特性的一种新方法，分别用这种方法及压痕／弯曲方法对一种可切削玻璃－陶瓷的阻力特性进行了实验测定，两种方法所得结果有很好的一致性。