Removal of impurities from liquid solutions by vacuum desorption with solvent evaporation

Mass transfer with solvent evaporation in the vapor-liquid two-phase film evaporators used for the removal of undesirable impurities from liquid solutions at low pressure is studied. The average concentrations of solution components in the falling liquid film are determined. The most efficient operating conditions for impurity removal, in which the resistance to mass transfer is concentrated in the liquid phase, are found. Original Russian Text ? V.N. Babak, T.B. Babak, L.P. Kholpanov, 2008, published in Teoreticheskie Osnovy Khimicheskoi Tekhnologii, 2008, Vol. 42, No. 6, pp. 654–670.     

Optical properties of doped bismuth telluride crystals in the region of plasma effects

The optical properties of bismuth telluride crystals doped with donor-and acceptor-type impurities are studied. The fact that energy corresponding to the resonance frequency of plasma oscillations of free charge carriers (plasmons) approaches the band-gap energy is detected in the infrared spectral region, where the main elementary excitations in the electronic system of these materials are observed. The mentioned approach of energies varies the intensity of electron-plasmon interaction, which affects the recombination processes in the materials widely used for the fabrication of thermoelectric energy converters.     

Sandia National Laboratories Validation Workshop: Structural dynamics application

This article specifies a virtual structural dynamic subsystem and some systems, as well as mathematical models that approximately simulate them. The purpose is to define a setting for model validations conceived by participants in the Sandia National Laboratories Validation Workshop. Some broad guidelines for the model validations are set, as well as a regulatory requirement to be satisfied by the target system. Participants are directed to present techniques for subsystem model validation, to analytically predict whether or not the regulatory requirement will be met, and to estimate the likelihood of accuracy of the prediction.     

Thomson scattering diagnostic systems in the ITER divertor

A diagnostic array has been developed for studying the operating modes of the divertor in the ITER tokamak-reactor using the Thomson scattering technique. The aim of this study is to measure the spatial profiles of the electron temperature and density. The structure of the diagnostic setup was selected on the basis of a classical diagnostic geometry and the high-resolution LIDAR system, which provide access to different regions of the divertor plasma. A severe radiation environment, limited access to the plasma in the ITER divertor, and a high-dust environment (the divertor plate erosion material) in the divertor volume pose many problems for performing diagnostics under unique conditions having no analogs in the tokamaks that are now in operation. Different methods for protecting optical surfaces from plasma-enriched deposition are proposed and analyzed. The efficiency of these methods has been demonstrated in bench tests. The concept of laser and detector systems and diffraction polychromators capable of operating at different electron temperatures with a lower limit of 1 eV, has been justified and approved.     

A device for measuring the equivalent resistance of an energized circuit section

A device for measuring the active resistance of a direct current energized circuit section is described. Owing to the use of up-to-date electronic components, an iteration measurement algorithm, and a sinusoidal signal as a test one, the following performance characteristics have been obtained: the measurement time is <1 s, and the error varies from 0.3 to 2.0% in a 100-Ω to 1-MΩ range and ≤25% in 10-to 100-Ω and 1-to 10-MΩ ranges.     

Some Thoughts on the Evolution of Work Teams in Organizations

In this time of flat, team-based and technology-enabled organizations the effectiveness of communication and team leadership practices will be more important than ever before. Therefore, we believe that some of the earlier, time-tested classic works on group dynamics and leadership are worthy of re-reading. We are particularly impressed by how relevant one of the oldest classics, Benne and Sheats' (1948) article on functional roles of group members, remains to this day.     

Evaluating software reuse alternatives: a model and its application to an industrial case study

We propose a model that enables software developers to systematically evaluate and compare all possible alternative reuse scenarios. The model supports the clear identification of the basic operations involved and associates a cost component with each basic operation in a focused and precise way. The model is a practical tool that assists developers to weigh and evaluate different reuse scenarios, based on accumulated organizational data, and then to decide which option to select in a given situation. The model is currently being used at six different companies for cost-benefit analysis of alternative reuse scenarios; we give a case study that illustrates how it has been used in practice.     

Effect of broaching on high-temperature fatigue behavior in notched specimens of INCONEL 718

Notches were machined in specimens of INCONEL 718 by a broaching process, where differing broaching runs led to differing extents of subsurface deformation and surface roughness. Fatigue tests were carried out at 600 °C with a trapezoidal loading waveform at 0.25 Hz. The broaching process that led to the more severe subsurface deformation (but lower surface roughness) showed the worst fatigue performance. Analysis of total strain amplitude in the notch root with the aid of an elastoplastic finite-element (FE) model showed that the work hardening related to the subsurface deformation caused by the different broaching can account for the difference in fatigue lives. Differences in initiation and growth behavior were seen for the two broached finishes as well as for broached and subsequently polished samples. These differences are discussed in terms of a change in crack growth initiation and growth mechanisms due to the presence of the work-hardened layer.     

Thermal Transformations of an Aluminoborophosphate Binder

Thermal transformations of a commercial aluminoborophosphate binder are studied in a broad temperature range by optical microscopy, x-ray diffraction, IR spectroscopy, and thermal analysis. The introduction of B₂O₃ reduces the temperature of phosphate polycondensation, enhances the stability of cyclometaphosphates in a broad temperature range (180–1100°C), and reduces the stability of hydrogen phosphates.