Series resonant ZCS‐PFM DC‐DC power converter with high‐frequency high‐voltage transformer link for high‐power magnetron drive

This paper presents a single lossless inductive snubber‐assisted ZCS‐PFM series resonant DC‐DC power converter with a high‐frequency high‐voltage transformer link for industrial‐use high‐power magnetron drive. The current flowing through the active power switches rises gradually at a turned‐on transient state with the aid of a single lossless snubber inductor, and ZCS turn‐on commutation based on overlapping current can be achieved via the wide range pulse frequency modulation control scheme. The high‐frequency high‐voltage transformer primary side resonant current always becomes continuous operation mode, by electromagnetic loose coupling design of the high‐frequency high‐voltage transformer and the magnetizing inductance of the high‐frequency high‐voltage transformer. As a result, this high‐voltage power converter circuit for the magnetron can achieve a complete zero current soft switching under the condition of broad width gate voltage signals. Furthermore, this high‐voltage DC‐DC power converter circuit can regulate the output power from zero to full over audible frequency range via the two resonant frequency circuit design. Its operating performances are evaluated and discussed on the basis of the power loss analysis simulation and the experimental results from a practical point of view. © 2005 Wiley Periodicals, Inc. Electr Eng Jpn, 153(3): 79–87, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20126     

Multiobjective dynamic load-dispatching method for optimal operation of power systems

A new practical method is proposed which gives a quasi-optimal solution of the dynamic load-dispatching problem formulated by a multiconstraint multiobjective optimization problem. Here, the multiple constraints are rate reserve constraints and power flow ones, and the multiple objectives are fuel cost and CO₂ emission. The proposed method is an integration of the following three techniques: (1) “Group Dispatch Scheme,” which is developed by the authors, is used to satisfy a violated constraint easily. This scheme consists of three steps. The first step is to classify all generators into two groups. One is the group which should be more loaded to satisfy the violated constraint, and the other is the should-be less loaded group. The second step is to add some load to the former group, and to subtract the same load from the latter. The third step is to dispatch each group load to each groups generators, respectively; (2) the dynamic load-dispatching algorithm is used which provides, in practical time, quasi-optimal generation trajectories; (3) the conventional weighting parametric method is used to obtain a Pareto optimal solution of multiobjective problems. The effectiveness of the method is clarified by a computer simulation on the actual power system of Kansai Electric Power Company.     

Sintering of fibrous barium titanate powder compacts with preferred orientation

The sintering of fibrous BaTiO₃ powder particles was investigated. Special emphasis was given to the role of particle orientation in the compact on densification and microstructure development. Compacts were made by dry-pressing. During the initial stage of sintering, the fibrous particles rearranged and bundles of particles were formed. The volume of pores between bundles of particles decreased on further heating. Grain growth started when the sintered density reached ca. 56% of the theoretical density. Higher temperatures of sintering increased the degree of the crystal axis orientation. Thus, highly orientated sintered bodies with high densities were prepared by heating at 1500 °C.     

Fabrication of blue-light emission fused-silica substrates by using Si-ion implantation and high-temperature annealing

We fabricated fused-silica substrates which emit blue light by using Si-ion implantation and high-temperature annealing. Photoluminescence peak wavelengths are around 400 nm, and the peak intensities can be remarkable after annealing above 1150 °C.     

Twin-Related Tetragonal Variants in Yttria Partially Stabilized Zirconia

Crystals of yttria partially stabilized zirconia were grown by the arc-image floating-zone technique and studied by transmission electron microscopy. Crystals annealed at 1700°C consist of tetragonal precipitates and a cubic matrix. The platelike domains in a precipitate are twin-related tetragonal variants stacked alternately parallel to the (011) twin plane. The axial relations between the tetragonal precipitate and the cubic matrix are [100]_tetragonal|[100]_cubic, [011]_tetragonal|[011]_cubic.     

Premixed flame propagating into a narrow channel at a high speed, part 2: Transient behavior of the properties of the flowing gas inside the channel

The behavior of a premixed flame propagating from a chamber into a narrow channel at a high speed was examined using high speed and instantaneous schlieren photography, ion current measurement with electrostatic probes, and temperature measurement with an optical method. From detailed measurements of flames passing through the channel, flame extinguishment in the channel, no matter whether transient or not, was found to occur due to quenching of the reacting gas by rapid turbulent mixing with cold fresh mixture at the downstream of the contraction region and by heat transfer to the cold channel walls. Extinguishment must occur when these heat losses exceed the heat released by the chemical reaction of the flowing mixture.     

Titania NOx sensors for exhaust monitoring

Oxide semiconductors have been examined to develop NO_x sensors for exhaust monitoring. Titania doped with trivalent elements, such as Al³⁺, Sc³⁺, Ga³⁺ or In³⁺, has a good sensitivity and selectivity to NO between 450 and 550 °C, and shows rapid response. A sensor probe for monitoring exhaust NO_x has been fabricated. Many kinds of interference gases, such as C₃H₆, CO and SO₂, have been found to have only a slight influence on the sensor response to NO. The influence of O₂ and H₂O is also negligible, except for the cases of 0% H₂O and fuel-rich conditions. In accordance with these results, the sensor probe operates satisfactority in the exhaust gas of various combustion conditions without interference from the various kinds of gas species in the exhaust gases.     

Pseudo-binary system Bi2O3-TeO2 in air

The phase equilibria in the pseudo-binary system Bi₂O₃-TeO₂ at 600° 950° C in air were examined by solid-state reaction techniques and X-ray powder diffraction method. Four pseudo-binary compounds appeared, i.e., -Bi₂O₃ type solid solution having a compositional range of (1-x)Bi₂O₃·xTeO₂ wherex=0 0.4 a new compound Bi₆Te₂O₁₅ which has an orthorhombic cell of a=2.27(4) nm, b=1.06(1) nm and c = 0.539(8) nm, 2Bi₂O₃ · 3TeO₂, and an unidentified phase Bi₂O₃·2TeO₂. The formation of the phase Bi₆Te₂O₁₅, in which all the Te ions are hexavalent, was confirmed by the thermogravimetry and by the Mössbauer spectra. The liquidus curves for whole system were determined by DTA method.     

One-Step Generation of Multiple Gene-Edited Pigs by Electroporation of the CRISPR/Cas9 System into Zygotes to Reduce Xenoantigen Biosynthesis

Xenoantigens cause hyperacute rejection and limit the success of interspecific xenografts. Therefore, genes involved in xenoantigen biosynthesis, such as GGTA1, CMAH, and B4GALNT2, are key targets to improve the outcomes of xenotransplantation. In this study, we introduced a CRISPR/Cas9 system simultaneously targeting GGTA1, CMAH, and B4GALNT2 into in vitro-fertilized zygotes using electroporation for the one-step generation of multiple gene-edited pigs without xenoantigens. First, we optimized the combination of guide RNAs (gRNAs) targeting GGTA1 and CMAH with respect to gene editing efficiency in zygotes, and transferred electroporated embryos with the optimized gRNAs and Cas9 into recipient gilts. Next, we optimized the Cas9 protein concentration with respect to the gene editing efficiency when GGTA1, CMAH, and B4GALNT2 were targeted simultaneously, and generated gene-edited pigs using the optimized conditions. We achieved the one-step generation of GGTA1/CMAH double-edited pigs and GGTA1/CMAH/B4GALNT2 triple-edited pigs. Immunohistological analyses demonstrated the downregulation of xenoantigens; however, these multiple gene-edited pigs were genetic mosaics that failed to knock out some xenoantigens. Although mosaicism should be resolved, the electroporation technique could become a primary method for the one-step generation of multiple gene modifications in pigs aimed at improving pig-to-human xenotransplantation.