Evaluation and Carbon Fiber Reinforced Polymer Strengthening of Existing Garage: Case Study

The concrete-repair fiber reinforced polymer technology emerged in the United States during the past 10 years. Since 1995, carbon fiber reinforced polymer (CFRP) has been applied to strengthen concrete decks of a troubled posttensioned garage in Atlanta. During the construction of the garage, design deficiencies were found. A remedial repair, involving heavily?reinforced, 7.6 cm (3 in.) thick Gunite (Shotcrete) beams, applied to the underside of the slab between drop panels in the east-west (E-W) direction, was developed in 1984. Since then, delamination of Gunite beams and other structural problems repeatedly occurred. Epoxy injection and other limited repairs were done over the years in an attempt to remediate the problems. In 2000, due to the growing delamination concerns, backed up with nondestructive impact-echo testing results, and due to the newest set of structural analyses that showed additional design deficiencies, Simpson Gumpertz & Heger developed a new and comprehensive remedial program. The first phase of this program included an in-depth mechanical in?situ load test program to study the strength and stiffness performance of the existing typical slab spans, including the effects of Gunite beams, the loss of Gunite beams due to delamination, and the CFRP?strengthing of spans. The tests showed that the CFRP repair of E-W spans with delaminated Gunite beams is warranted and that it performs well. The performance of the existing typical spans in the north-south direction was found to be acceptable without any repairs. Further monitoring of the performance of Gunite beams is required, and additional CFRP strengthening will be done periodically. In addition, structural deficiencies of the typical second-level end bays were repaired using additional steel framing supports.     

Life-Cycle Cost Analysis using Deterministic and Stochastic Methods: Conflicting Results

Life-cycle cost analysis is an essential approach to differentiating alternative rehabilitation strategies for steel bridge paint systems. An economic analysis (EA), which is a deterministic method, and the Markov decision process (MDP), which is a stochastic method, were used to carry out the life-cycle cost analysis. These analyses were applied to data from two state Departments of Transportation. The deterioration curves for steel bridge paint condition rating against age were constructed. Different rehabilitation scenarios were proposed for steel bridge paint. The EA and the MDP were used to analyze and differentiate among the proposed rehabilitation scenarios. The results of the EA were different from those of MDP for the two data sets. MDP favored the “do nothing” scenario until the end of paint life and then a complete repainting. EA indicated that the scenario “do spot repairs at state 3 of the paint life” and repeat that until the end of the bridge life was superior. The results were analyzed to determine the reason for the conflict.     

Synthesis and thermal cure of high molecular weight polybenzoxazine precursors and the properties of the thermosets

High molecular weight polybenzoxazine precursors have been synthesized from aromatic or aliphatic diamine and bisphenol-A with paraformaldehyde. The precursors were obtained as soluble white powder. Molecular weight was estimated from the size exclusion chromatography to be several thousands. The structure of the precursors was confirmed by IR, ¹H NMR and elemental analysis, indicating the presence of cyclic benzoxazine structure. The ratio of the ring-closed benzoxazine structure and the ring-opened structure in the high molecular weight precursor was estimated from ¹H NMR spectrum and also from the exotherm of DSC, showing that the ratio of the ring-closed benzoxazine structure was 77–98%. The precursor solution was cast on glass plate, giving transparent and self-standing precursor films, which was thermally cured up to 240 °C to give brown transparent polybenzoxazine films. The toughness of the crosslinked polybenzoxazine films from the high molecular weight precursors was greatly enhanced compared with the cured film from the typical low molecular weight monomer. Tensile measurement of the polybenzoxazine films revealed that polybenzoxazine from aromatic diamine exhibited the highest strength and modulus. While, polybenzoxazine from longer aliphatic diamine had higher elongation at break. The viscoelastic analyses showed that the glass transition temperature of the polybenzoxazines derived from the high molecular weight precursors were as high as 238–260 °C. Additionally, these novel polybenzoxazine thermosets showed excellent thermal stability.     

Influence of High-Pressure Coolant Assistance on the Machinability of the Titanium Alloy Ti555–3

The origin of this article is the quantification of productivity gains and the improvement in surface integrity seen for a recent titanium alloy that is seeing increasing use in the aeronautical industry. The Ti555–3 titanium alloy, which is starting to find greater application in the aeronautical field, exhibits certain difficulties in terms of machining. High Pressure Coolant (HPC) assisted turning consists of projecting a high pressure coolant jet between the chip and the tool. Comparisons are made between assisted turning using variable jet pressure and conventional turning (dry and classical lubrication). It is shown that it is possible to improve productivity by using HPC-assisted machining. The results highlight good chip fragmentation and a great improvement of tool life with HPC assistance. Surface integrity is also shown to be improved, through surface roughness parameters that decrease, and surface residual stresses that become more compressive. These effects have been attributed to the thermo-mechanical action of the coolant jet resulting in lower cutting forces, lower coefficient of friction and lower temperature in the cutting zone.     

A crystal-tolerant fully integrated CMOS low-IF dual-band GPS receiver

This paper presents the design of a dual-band L1/L2 GPS receiver, that can be easily integrated in portable devices (mainly GSM mobile phones). For the ease of integration with GSM wireless systems the receiver can tolerate most of the common GSM crystals, besides the GPS crystals, this will eliminate the need to use another crystal on board. A new frequency plan is presented to satisfy this requirement. A low-IF receiver architecture is used for dual-band operation with analog on-chip image rejection. The receiver is composed of a narrow-band LNA for each band, dual down-conversion mixers, a variable-gain channel filter, a 2-bit analog-to-digital converter, and a fully integrated frequency synthesizer including an on-chip VCO and loop filter. The complex filter can accept IF frequency variation of 10% around 4.092 MHz which allows the use of the commonly used 10/13/26 MHz GSM crystals and all the GPS crystals. The synthesizer generates the LO signals for both L1/L2 bands with an average phase noise of −95 dBc/Hz. The receiver exhibits maximum gain of 112 and 115 dB, noise figures of 4 and 3.6 dB, and input compression points of −76 and −79 dBm for L1 and L2, respectively. An on-chip variable-gain channel filter provides IF image rejection greater than 25 dB and gain control range over 80 dB. The receiver is designed in 0.13 μm CMOS technology and consumes 18 mW from a 1.2-V supply.     

Anaerobic biodegradability and treatment of grey water in upflow anaerobic sludge blanket (UASB) reactor

Feasibility of grey water treatment in an upflow anaerobic sludge blanket (UASB) reactor operated at different hydraulic retention time (HRT) of 16, 10 and 6h and controlled temperature of 30 degrees C was investigated. Moreover, the maximum anaerobic biodegradability without inoculum addition and maximum removal of chemical oxygen demand (COD) fractions in grey water were determined in batch experiments. High values of maximum anaerobic biodegradability (76%) and maximum COD removal in the UASB reactor (84%) were achieved. The results showed that the colloidal COD had the highest maximum anaerobic biodegradability (86%) and the suspended and dissolved COD had similar maximum anaerobic biodegradability of 70%. Furthermore, the results of the UASB reactor demonstrated that a total COD removal of 52-64% was obtained at HRT between 6 and 16 h. The UASB reactor removed 22-30% and 15-21% of total nitrogen and total phosphorous in the grey water, respectively, mainly due to the removal of particulate nutrients. The characteristics of the sludge in the UASB reactor confirmed that the reactor had a stable performance. The minimum sludge residence time and the maximum specific methanogenic activity of the sludge ranged between 27 and 93 days and 0.18 and 0.28 kg COD/(kg VS d).     

Characterization and Performance Analysis of LTE-Advanced Uplink Signals in Presence of Amplifier Nonlinearity

Carrier aggregation (CA) is the new technique standardized for the next generation of cellular networks, namely long term evolution-advanced (LTE-Advanced) in response to the continuous demands of increased data rates. One of the challenges facing the new CA technique is the increased dynamic range of the transmitted uplink (UL) signal that represents the sum of different carrier components in the time domain. This increased dynamic range makes the signal more susceptible to nonlinear distortion caused by nonlinear devices at the transmitter and eventually leads to performance degradation. In this paper, we investigate the effect of the nonlinear distortion on the UL of LTE-Advanced. Towards this investigation, statistical characterization of the UL signal is conducted, where it is established that it has a quasi-Gaussian characteristics. Also, statistical characterization of the nonlinear distortion noise at the receiver detector is performed, where it appears evident that it can be regarded as a complex Gaussian process. Through these characterizations, an analytical expression for the bit error rate, as a function of the system parameters and the input back-off level, is derived. The analytical results are validated via simulation results, where the good agreements confirm the pursued approach and the taken assumptions.     

Ethanol from lactose in salted cheese whey by recombinant Saccharomyces cerevisiae

Seven yeast recombinants were selected from 57 fusant colonies on the basis of higher DNA content, nuclear diameter and ethanol yield compared to parental Saccharomyces cerevisiae ATCC 4126 and Kluyveromyces lactis CBS 683. Six recombinants out of the above colonies revealed growth on lactose and sucrose, indicating that they are S. cerevisiae with transformed β-galactosidase systems. The fusant colonies were investigated with respect to their capacity to convert lactose in salted cheese whey into ethanol. Among these recombinants that showed high tolerance towards sodium chloride and higher ethanol yield than lactose fermenting parental K. lactis CBS 683, SK-1 exhibited high tolerance up to 4 g dl^–1 sodium chlonride with an ethanol yield of 4.66 ml dl^–1 (v/v) , SK-23 tolerated 6 g dl^–1 sodium chloride with an ethanol yield of 4.14 ml dl^–1 (v/v) and SK-26 showed resistance towards 8 g dl^–1 sodium chloride and give an ethanol yield of 3 ml dl^–1 (v/v).