Laser scanning path generation considering photopolymer solidification in micro-stereolithography

It is essential to automate the scanning path generation process to effectively implement the micro-stereolithography. However, a scanning path that is generated based only on a 3D CAD model introduces dimensional inaccuracies. In micro-stereolithography, the photopolymer solidification is affected by fabrication conditions, such as the optical properties (laser power, laser scanning speed, laser scanning pitch focusing condition, etc.) and material properties of the photopolymer. Thus, the photopolymer solidification phenomena must be considered when generating a laser scanning path. In this paper, a scanning path generation algorithm that uses 3D CAD data and considers the photopolymer solidification phenomena is proposed to improve the dimensional accuracy in micro-stereolithography. Multi-line photopolymer solidification experiments were performed for various laser scanning conditions to examine the photopolymer solidification phenomena. From these experiments, linear relations between the solidification length (width) and scanning length (width) were acquired and stored in a database. Subsequently, these data were utilized to compensate the scanning path of the laser beam. In addition, experiments for determining the layer thickness in the z-direction were performed and these results were also used in the scanning path generation algorithm.This research was supported by the Highly Advanced National Project (http://www.most.go.kr), which performs some of the National R&D Program, and sponsored by the Korean Ministry of Science and Technology under the contract project code M10214000116-02B1500-02010.     

Acidogenic fermentation of blended food‐waste in combination with primary sludge for the production of volatile fatty acids

The performance of a laboratory‐scale anaerobic acidogenic fermenter fed with a mixture of blended kitchen food‐waste and primary sludge from a sewage treatment plant was investigated for the production of volatile fatty acids (VFA). The operating variables for acidogenic fermentation were kitchen food‐waste content (10 and 25 wt %), hydraulic retention time (HRT: 1, 3 and 5 days), temperature (ambient: 18 ± 2 °C, and mesophilic: 35 ± 2 °C) and pH (varied from 5.2 to 6.7). The experimental results indicated that effluent VFA concentrations and VFA production rates were higher at ambient temperature than at mesophilic conditions. The net amount of VFA with 10 wt % food‐waste increased up to 920 mg dm^?3 with an increase of HRT, but contrasting results (a decrease of 2610 mg dm^?3) were found due to the conversion of VFA into biogas in the case of 25 wt % food‐waste, which increased significantly at HRT of 3–5 days. In terms of biogas composition (CO₂ and CH₄), the organic matter was converted into CO₂ through the oxidative pathway by facultative species at low temperature while mesophilic temperature and optimum pH (6.3–7.8) played a pivotal role in increasing rate of conversion of VFA into biogas by methanogenesis. Rates of VFA production and their conversion are dependent on the food‐waste content in the mixture. Yet, the higher concentration of food‐waste (25% compared with 10%) did not produce VFA proportionally due to the increased rate of conversion of VFA into gaseous products. The maximum VFA production rate (0.318 g VFA_produced g^?1 VS_fed day^?1) was achieved in the 10 wt % food‐waste at ambient temperature and at a 5‐day HRT. Copyright © 2005 Society of Chemical Industry     

Intraoperative neurological monitoring

Intraoperative neurological monitoring (INM) is the evaluation of the nervous system within the operating room (OR) environment. In this paper, the INM system is tested in a clinical setting in comparison with conventional somatosensory evoked potential (SEP) monitoring. The study results demonstrate the capability of the INM system in extracting clearer and more stable SEP signals. The high SNR of SEP signals collected in various clinical environments, including the OR, makes the INM system a robust platform for continuous monitoring. While the current use of EP monitoring is limited to intermittent analysis by a highly trained clinical neurophysiologist, the authors believe in changing this paradigm by developing continuous monitoring systems, such as the INM system, capable of automated quantitative EP analysis. This noninvasive monitoring modality will allow for a wider range of use in clinical practice. Based on volunteer and clinical patient studies, the INM monitoring system demonstrates much greater reliability and accuracy via the artifact rejection and denoising strategies. It provides more strategic filtering options for different situations under which the clinical SEP response signal could be greatly contaminated and distorted. Furthermore, the INM system offers a promising approach to signal extraction in real-time monitoring during SEP research.     

Effects of solid retention time on the performance of submerged anoxic/oxic membrane bioreactor.

In this study, four similar bench-scale submerged Anoxic/Oxic Membrane Bioreactors (MBR) were used simultaneously to investigate the effects of solids retention time (SRT) on organic and nitrogen removal in MBR for treating domestic wastewater. COD removal efficiencies in all reactors were consistently above 94% under steady state conditions. Complete conversion of NH(4+)-N to NO(3-)-N was readily achieved over a feed NH(4+)-N concentration range of 30 to 50 mg/L. It was also observed that SRT did not significantly affect the nitrification in the MBR systems investigated. The average denitrification efficiencies for the 3, 5, 10 and 20 days SRT operations were 43.9, 32.6, 47.5 and 66.5%, respectively. In general, the average effluent nitrogen concentrations, which were mainly nitrate, were about 22.2, 27.6, 21.7 and 13.9 mg/L for the 3, 5, 10 and 20 days SRT systems, respectively. The rate of membrane fouling at 3 days SRT operation was more rapid than that observed at 5 days SRT. No fouling was noted in the 10 days and 20 days SRT systems during the entire period of study.     

Rapid and comprehensive indicator for evaluation of performance of treatment processes and of river waters.

Naturally occurring UV active compounds, commonly present in almost all source waters, can be rapidly monitored by their ultraviolet absorbance at 260 nm (E260). Herein, the extent of correlation between the E260 and the removal efficiency of the hazardous contaminants, endocrine disrupters and dioxins, were investigated using various treatment and river source waters. The detection of various types of hazardous contaminants using sophisticated analytical methods, such as high resolution gas chromatography (HRGC)/high resolution mass spectrometry (HRMS) and high performance liquid chromatography (HPLC)/inductively coupled plasma (ICP)/mass spectrometry (MS), as well as various short-term bioassays, can require hours or even days for results to be obtained. The removal of the E260 correlated well with those of individual contaminants, such as endocrine disruptor chemicals and dioxins, with the various treatment processes employed. In the plots of the endocrine disrupters against the DOC/E260, a correlation was found with the endocrine activity of the Korean/Japanese river waters employed in this study.     

A VLSI CMOS delay oriented waveform converter for polyphasefrequency synthesizer

In this paper, we present a waveform converter implemented on a 0.25-μm CMOS technology using a dedicated design methodology (Delay Oriented Design). The circuit converts a square wave signal in both in-phase and quadrature-phase sinusoidal differential outputs. It also multiplies the frequency by seven. The output frequency range of this converter extends from 1.05 GHz up to 2.17 GHz. This converter is dedicated for the design of a third-generation mobile phone synthesizer using a double-loop architecture. For an output frequency of 2 GHz, the measured phase noise at 10-kHz offset from the carrier is -97 dBc/Hz. The circuit consumes 50 mW from a 2.5-V supply     

Modelling thermal degradation of composite materials

A one–dimensional, transient thermal degradation heat transfer model for the response of composite materials when exposed to fire is presented. The model can handle layers of different materials. Material properties are functions of temperature. The reaction can be specified using Arrhenius‐type parameters or by inputting a density–temperature relationship determined by any experimental technique such as thermogravimetric analysis. The model is validated against the experimental data presented in Boyer's 1984 dissertation. Overall, the model provides excellent agreement with the experimental data. It is shown that very little difference is found between results arrived at by Arrhenius kinetics and results obtained by specifying the easier to measure density–temperature relationship. From this it is concluded that this technique is a viable alternative to Arrhenius‐type models. Copyright © 2006 John Wiley & Sons, Ltd.     

Effect of the Treatment Temperature on the Surface Drying Set of Sugi Boxed-Heart Square Timber

High-temperature and controlled humidity treatment before drying has proven to be highly effective in preventing surface checks by forming drying sets in the surface layer of boxed-heart square timber in Japan. In this study, we examined the differences of the surface drying sets on sugi timber under different treatment temperatures. As a result, the width of a surface check after drying was much smaller at a treatment temperature of 120°C than at 80°C, and this indicates that the drying set with 120°C treatment would be larger than that with 80°C treatment. Also we observed that treatment temperature had a greater effect on the drying set as the drying advanced.     

High-temperature sensible-heat storage options

Alkali-metal carbonate salts meet the requirements for high-temperature solar central receiver systems, but because of their corrosiveness they present special problems in the design of storage tanks. In order to reduce corrosion and temperature sufficiently to retain strength in the storage containing wall, internal and thermal insulation is required. We present design options and operation criteria for sensible-heat, molten-salt storage with internal insulation.