Highly Selective SAM–Nanowire Hybrid NO2 Sensor: Insight into Charge Transfer Dynamics and Alignment of Frontier Molecular Orbitals

Organic–inorganic hybrid gas sensors can offer outstanding performance in terms of selectivity and sensitivity towards single gas species. The enormous variety of organic functionalities enables novel flexibility of active sensor surfaces compared to commonly used pure inorganic materials, but goes along with an increase of system complexity that usually hinders a predictable sensor design. In this work, an ultra‐selective NO₂ sensor is realized based on self‐assembled monolayer (SAM)‐modified semiconductor nanowires (NWs). The crucial chemical and electronic parameters for an effective interaction between the sensor and different gas species are identified using density functional theory simulations. The theoretical findings are consistent with the experimentally observed extraordinary selectivity and sensitivity of the amine‐terminated SnO₂ NW towards NO₂. The energetic position of the SAM–gas frontier orbitals with respect to the NW Fermi level is the key to ensure or impede an efficient charge transfer between the NW and the gas. As this condition strongly depends on the gas species and the sensor system, these insights into the charge transfer mechanisms can have a substantial impact on the development of highly selective hybrid gas sensors.     

Variability in oil content and fatty acid composition in wild northern currants

Seed oils of wild berries of alpine currant (AC) and northern redcurrant (NRC) were investigated. Oil contents of AC and NRC varied between 4.9 % and 9.7% and between 12.8% and 38.5%, respectively. The proportions of α-linolenic, γ-linolenic and stearidonic acids were higher in NRC (means of 21.7, 12.3 and 5.4%, respectively) than in AC (16.8, 8.6 and 3.0%). The growth areas of NRC can be divided into two distinct groups according to the proportions of different polyunsaturated fatty acids. Oil content of NRC correlated negatively to the proportion of linoleic acid and positively to that of stearidonic acid. There were significant correlations between all polyunsaturated fatty acids in NRC but correlations were less obvious in AC. Interestingly, the correlation between linoleic and γ-linolenic acids was positive in NRC but negative in AC. α-Linolenic and stearidonic acids showed positive correlations in both species. In NRC the synthesis of triunsaturated fatty acids is directed either towards α-linolenic or γ-linolenic acids. Results showed great potential in NRC and AC for plant breeding due to the natural variation in the content and composition of the seed oils for functional nutrients. Received: 20 August 1999 / Revised version: 29 October 1999     

Comparative experimental study of sand and binder for flowability and casting mold quality

A good sand mold is an indispensable prerequisite to obtaining a good metal casting. Although sand casting is one of the oldest metal forming technique known to humans, it still has a lot to discover. In a bid to meet the ever-growing demand for quality, economics and increasing environmental restrictions, research is still ongoing to optimize for example the process of making the sand mold. This paper presents a comparative study of six different foundry sands for flowability using simple inexpensive apparatus and some quality parameters achieved by these sands when used with three different types of binder, two organic and one inorganic. The study aims to facilitate the choice of mold materials with a more extensive outlook into their characteristics through a serious of sand and mold tests. A good comparison of already existing materials provides a good reference point when novel materials are investigated. All the sands exhibited ‘good’ flow property according to the simple flowability tests done. However, not the same consensus for flowability rank is reached by all the flow tests. The mold quality tests reveal the strength, loss on ignition and permeability values achieved with each of the binder and sand combination which can also be used in mold material selection.     

An Experimental and Computational Study on the Melting Behaviour of AOD and Chromium Converter Slags

The campaigns of the AOD and chromium converters are often limited by the strong wear of the refractory materials in certain areas (usually tuyere zone). Slag protection (in which the slag is left to solidify at the converter walls after the tapping of the metal) has been considered to be an option in prolonging the campaigns of the converters. In order to study the possibilities of the slag protection, the purpose of this work was to determine the melting behaviour of the AOD and chromium converter slags; i. e. the solidus and liquidus temperatures and the composition of solid phases as a function of temperature in different slag compositions. Examination was executed using both computational (FactSage software) and experimental (optical dilatometer/SEM) methods. It was noticed that when burned dolomite was added into the slags, the increased MgO‐contents had a strong influence on the melting behaviour. Even small changes (a few percent) in the MgO‐content had a very strong influence (a few hundred degrees centigrade) on the solidus and liquidus temperatures. Solid phases that are formed during the solidification are also different in slags with and without burned dolomite addition.     

Few-layer graphene synthesis on a dielectric substrate

We report on few-layer graphene synthesis on fused silica, with the help of pre-deposited copper films with thickness of few hundred nanometers, by using chemical vapor deposition technique. Depending on the copper film thickness, the deposited graphene samples on copper/silica interface were either micron sized graphene flakes or uniform graphene films of a sub-millimeter width. The quality of graphene grown beneath the pre-deposited copper film was found to be comparable with that of graphene grown on bulk copper. The developed technique opens new route towards the space-selective CVD graphene growth on dielectric substrates.     

Plasma-chemical reduction of iron oxide photoanodes for efficient solar hydrogen production

We demonstrate the effect of hydrogen plasma treatment on hematite films as a simple and effective strategy for modifying the existing substrate to improve significantly the band edge positions and photoelectrochemical (PEC) performance. Plasma treated hematite films were consist of mixed phases (Fe₃O₄:α-Fe₂O₃) which was confirmed by XPS and Raman analysis, treated films also showed higher absorption cross-section and were found to be a promising photoelectrode material. The treated samples showed enhance photocurrent densities with maximum of 3.5 mA/cm² at 1.8 V/RHE and the photocurrent onset potentials were shifted from 1.68 V_RHE (untreated) to 1.28 V_RHE (treated). Hydrogen plasma treatment under non-equilibrium conditions induced a valence dynamics among Fe centers in the sub-surface region that was sustained by the incorporation of hydrogen in the hematite lattice as supported by the density functional theory calculations.     

Behavior of HVOF WC-10Co4Cr Coatings with Different Carbide Size in Fine and Coarse Particle Abrasion

A modified ASTM G 65 rubber wheel test was employed in wet and dry conditions using 220 nm titania particles and 368 μm sand particles, respectively. Both tests were conducted on WC-CoCr coatings produced with two powders with different carbide grain sizes (conventional and sub-micron) to address the effect of carbide size and abrasive medium characteristics on the wear performance. The same spot before and after the wet abrasion wear testing was analyzed in detail using SEM to visualize wear mechanisms. It was shown that the wear mechanism depends on the relative size of the carbide and abrasive particles. Wear mechanisms in dry sand abrasion were studied by analyzing the single scratches formed by individual abrasive particles. Interaction of surface open porosity with moving abrasive particles causes formation of single scratches. By tailoring the carbide size, the wear performance can be improved.     

Diffractive-optics-based sensor as a tool for detection of biocompatibility of titanium and titanium-doped hydrocarbon samples

Adsorption of the elongated human plasma fibrinogen (HPF) and globular human serum albumin molecules on a titanium-based surface is monitored by analyzing permittivity and optical roughness of protein-modified surfaces by using a diffractive optical element (DOE)-based sensor and variable angle spectro-ellipsometry (VASE). Both DOE and VASE confirmed that fibrinogen forms a thicker and more packed surface adlayer compared to a more porous and weakly adsorbed albumin adlayer. A linear relation of the permittivity (ε(')) and dielectric loss (ε(')) was found for some of the dry titanium-doped hydrocarbon (TDHC) surfaces with excellent HPF adsorption ability. We discuss some aspects of TDHC's aging and its possible effects on fibrinogen adsorption.     

Postpartum Weight Retention is Associated with Elevated Ratio of Oxidized LDL Lipids to HDL-Cholesterol

Oxidized LDL lipids (ox‐LDL) are associated with lifestyle diseases such as cardiovascular diseases, metabolic syndrome and type 2 diabetes. The present study investigated how postpartum weight retention effects on ox‐LDL and serum lipids. The study is a nested comparative research of a cluster‐randomized controlled trial, NELLI (lifestyle and counselling during pregnancy). During early pregnancy (8–12 weeks) and 1 year postpartum, 141 women participated in measurements for determining of plasma lipids: total cholesterol (T‐C), LDL‐cholesterol (LDL‐C), HDL‐cholesterol (HDL‐C), triacylglycerols (TAG) and ox‐LDL. Subjects were stratified into tertiles (weight loss, unaltered weight and weight gain groups) based on their weight change from baseline to follow‐up. Ox‐LDL was determined by baseline level of conjugated dienes in LDL lipids. Among the group of weight gainers, concentration of TAG reduced less (?0.14 vs. ?0.33, p = 0.002), HDL‐C reduced more (?0.31 vs. ?0.16, p = 0.003) and ox‐LDL/HDL‐C ratio increased (3.0 vs. ?0.2, p = 0.003) when compared to group of weight loss. Both T‐C and LDL‐C elevated more (0.14 vs. ?0.21, p = 0.008; 0.31 vs. 0.07, p = 0.015) and TAG and ox‐LDL reduced less (?0.33 vs. 0.20, p = 0.033; ?3.33 vs. ?0.68, p = 0.026) in unaltered weight group compared to weight loss group. The women who gained weight developed higher TAG and ox‐LDL/HDL‐C ratio as compared to those who lost weight. Postpartum weight retention of 3.4 kg or more is associated with atherogenic lipid profile.     

Microwave absorption properties of pyrolytic carbon nanofilm

We analyzed the electromagnetic (EM) shielding effectiveness in the Ka band (26 to 37 GHz) of highly amorphous nanometrically thin pyrolytic carbon (PyC) films with lateral dimensions of 7.2 × 3.4 mm², which consists of randomly oriented and intertwined graphene flakes with a typical size of a few nanometers. We discovered that the manufactured PyC films, whose thickness is thousand times less than the skin depth of conventional metals, provide a reasonably high EM attenuation. The latter is caused by absorption losses that can be as high as 38% to 20% in the microwave frequency range. Being semi-transparent in visible and infrared spectral ranges and highly conductive at room temperature, PyC films emerge as a promising material for manufacturing ultrathin microwave (e.g., K_a band) filters and shields.