Flux-based two-degrees-of-freedom algorithm for three-phase electronic converter control

This letter integrates the tracking robustness of two-degrees-of-freedom control and fast dynamic response of flux-based, pulse-width modulation to develop a new current controller for high performance, three-phase electronic converter control. Theoretical analysis shows that the controller can simultaneously achieve good steady-state, transient and harmonic performance, which are challenges not previously met by existing current controllers reported in the literature. Experimental results are presented to verify the performance and practicality of the proposed controller.     

Wideband microwave filter constructed by asymmetrical compact microstrip resonator and floating plate coupling structure

The realisation of a microwave filter is presented by using the asymmetrical compact microstrip resonator and floating plate coupling structures. The filter demonstrates the properties of low insertion loss, wide pass bandwidth and two controllable transmission zeros, which results in fast roll-off responses near to the corner frequencies of the passband. It also has the advantages of compact size, ease of fabrication and absence of via holes. An X-band prototype with 34% fractional bandwidth was designed and fabricated to verify the proposed design concept. Good agreement between simulation and measurement was obtained.     

Three-Level AC–DC–AC Z-Source Converter Using Reduced Passive Component Count

This paper presents a three-level AC-DC-AC Z-source converter with output voltage buck-boost capability. The converter is implemented by connecting a low-cost front-end diode rectifier to a neutral-point-clamped inverter through a single X-shaped LC impedance network. The inverter is controlled to switch with a three-level output voltage, where the middle neutral potential is uniquely tapped from the star-point of a wye-connected capacitive filter placed before the front-end diode rectifier for input current filtering. Through careful control, the resulting converter can produce the correct volt-second average at its output, while simultaneously achieving inductive voltage boosting by shooting through either an appropriately selected inverter phase-leg or two phase-legs being commanded simultaneously. More interestingly, these performance features are achieved with no increase in the number of semiconductor commutations, and hence, no increase in switching losses. The proposed converter therefore offers a low-cost alternative to applications that need to ride through frequent input voltage sags. For confirming the converter performance, experimental testing using a constructed laboratory prototype is performed with its captured results presented in a later section of the paper.     

A PARALLEL COUPLED-LINE FILTER USING VLSI BACKEND INTERCONNECT WITH HIGH RESISTIVITY SUBSTRATE

This paper reports our progress in developing parallel coupled-line filters based on Si-based VLSI backend interconnects for millimeter-wave applications. The resonant frequency of this coupled-line filter increases with increasing spacing-gap and with increasing IDM thickness. By using high resistivity substrate, the parallel coupled-line band-pass filter is extremely effective in reducing substrate loss, and also provides very low insertion loss, even at the millimeter-wave regime. In addition, the parallel coupled-line filter suitable for advanced system-on-a-chips at the millimeter wave application achieves high performance characteristics, which show low insertion loss, wide band, and compatibility with standard VLSI process.     

Nanotechnology‐Enabled Closed Loop Insulin Delivery Device: In Vitro and In Vivo Evaluation of Glucose‐Regulated Insulin Release for Diabetes Control

Recently, a new multifunctional, bio‐inorganic nanocomposite membrane with the ability to self‐regulate the release of insulin in response to blood glucose (BG) levels was reported. Herein, the application of this material as part of a small, implantable, closed‐loop insulin delivery device designed to continuously monitor BG concentrations and regulate insulin release is proposed. The insulin delivery device consists of a nanocomposite glucose‐responsive plug covalently bound to an insulin reservoir made of surface‐modified silicone. The plug is prepared with crosslinked bovine serum albumin (BSA) and enzymes (glucose oxidase (GOx) and catalase (CAT)), pH‐responsive hydrogel nanoparticles, and multifunctional MnO₂ nanoparticles. The plug functions both as a glucose sensor and controlled delivery unit to release higher rates of insulin from the reservoir in response to hyperglycemic BG levels and basal insulin rates at normal BG concentration. The surfaces of the device are modified by silanization followed by PEGylation to ensure its safety and biocompatibility and the stability of encased insulin. Our results show that insulin release can be modulated in vitro in response to glucose concentrations. In vivo experiments show that the glycemia of diabetic rats can be controlled with implantation of the prototype device. The glucose‐responsiveness of the device is also demonstrated by rapid drop in BG level after challenging diabetic rats with bolus injection of glucose solution. In addition, it is demonstrated that surface PEGylation of the device is necessary for reducing the immune response of the host to the implanted foreign object and maintaining insulin stability and bioactivity. With this molecular architecture and the bio‐inorganic nanocomposite plug, the device has the ability to maintain normal BG levels in diabetic rats.     

Solvent‐Induced Morphology in Polymer‐Based Systems for Organic Photovoltaics

Studies on the influence of four different solvents on the morphology and photovoltaic performance of bulk‐heterojunction films made of poly(3‐hexylthiophene) (P3HT) and [6,6]‐phenyl‐C₆₁ butyric acid methyl ester (PCBM) via spin‐coating for photovoltaic applications are reported. Solvent‐dependent PCBM cluster formation and P3HT crystallization during thermal annealing are investigated with optical microscopy and grazing‐incidence wide‐angle X‐ray scattering (GIWAXS) and are found to be insufficient to explain the differences in device performance. A combination of atomic force microscopy (AFM), X‐ray reflectivity (XRR), and grazing‐incidence small‐angle X‐ray scattering (GISAXS) investigations results in detailed knowledge of the inner film morphology of P3HT:PCBM films. Vertical and lateral phase separation occurs during spin‐coating and annealing, depending on the solvent used. The findings are summarized in schematics and compared with the IV characteristics. The main influence on the photovoltaic performance arises from the vertical material composition and the existence of lateral phase separation fitting to the exciton diffusion length. Absorption and photoluminescence measurements complement the structural analysis.     

Distributed Rate Allocation for Inelastic Flows

A common assumption behind most of the recent research on network rate allocation is that traffic flows are elastic, which means that their utility functions are concave and continuous and that there is no hard limit on the rate allocated to each flow. These critical assumptions lead to the tractability of the analytic models for rate allocation based on network utility maximization, but also limit the applicability of the resulting rate allocation protocols. This paper focuses on inelastic flows and removes these restrictive and often invalid assumptions. First, we consider nonconcave utility functions, which turn utility maximization into difficult, nonconvex optimization problems. We present conditions under which the standard price-based distributed algorithm can still converge to the globally optimal rate allocation despite nonconcavity of utility functions. In particular, continuity of price-based rate allocation at all the optimal prices is a sufficient condition for global convergence of rate allocation by the standard algorithm, and continuity at at least one optimal price is a necessary condition. We then show how to provision link capacity to guarantee convergence of the standard distributed algorithm. Second, we model real-time flow utilities as discontinuous functions. We show how link capacity can be provisioned to allow admission of all real-time flows, then propose a price-based admission control heuristics when such link capacity provisioning is impossible, and finally develop an optimal distributed algorithm to allocate rates between elastic and real-time flows.     

Lipid‐Containing Polymer Vesicles with pH/Ca2+‐Ion‐Manipulated,Size‐Selective Permeability

Polymeric vesicles attained from the self‐assembly of distearin (a diacylglycerol lipid)‐conjugated poly(acrylic acid) (PAAc) with various distearin contents in the aqueous phase show the capability of control over the vesicular‐wall permeability to hydrophilic solutes of varying sizes by a simple manipulation of the external pH. The pH sensitivity of the vesicle membranes in size‐selective permeability is largely dependent upon the lipid content of copolymer. By the addition of CaCl₂ in aqueous vesicle suspensions, the pH‐evolved assembly structure and the membrane permeability can be immobilized with promoted resistance to further pH alteration, along with an additional counterion screening effect that reduces the pH required for the onset of polar solutes of certain sizes to pass through the membranes. Small‐angle X‐ray scattering (SAXS) measurements of the vesicle structure in the aqueous phase indicate that the pH‐regulated permeability to polar solutes is virtually governed by the extent of hydration and swelling of the vesicle membranes, and the lipid residues within each vesicle wall are packed into the ≈4–5 repeating lamellar islet structure surrounded by PAAc segments.     

Channel capacity and state estimation for state-dependent Gaussian channels

We formulate a problem of state information transmission over a state-dependent channel with states known at the transmitter. In particular, we solve a problem of minimizing the mean-squared channel state estimation error E/spl par/S/sup n/ - S/spl circ//sup n//spl par/ for a state-dependent additive Gaussian channel Y/sup n/ = X/sup n/ + S/sup n/ + Z/sup n/ with an independent and identically distributed (i.i.d.) Gaussian state sequence S/sup n/ = (S/sub 1/, ..., S/sub n/) known at the transmitter and an unknown i.i.d. additive Gaussian noise Z/sup n/. We show that a simple technique of direct state amplification (i.e., X/sup n/ = /spl alpha/S/sup n/), where the transmitter uses its entire power budget to amplify the channel state, yields the minimum mean-squared state estimation error. This same channel can also be used to send additional independent information at the expense of a higher channel state estimation error. We characterize the optimal tradeoff between the rate R of the independent information that can be reliably transmitted and the mean-squared state estimation error D. We show that any optimal (R, D) tradeoff pair can be achieved via a simple power-sharing technique, whereby the transmitter power is appropriately allocated between pure information transmission and state amplification.     

Characterization of Zn1?xMgxO Films Prepared by the Sol–Gel Process and Their Application for Thin-Film Transistors

Transparent semiconductor thin films of Zn_1−x Mg _x O (0 ≤ x ≤ 0.36) were prepared using a sol–gel process; the crystallinity levels, microstructures, and optical properties affected by Mg content were studied. The experimental results showed that addition of Mg species in ZnO films markedly decreased the surface roughness and improved transparency in the visible range. A Zn_1−x Mg _x O film with an x-value of 0.2 exhibited the best average transmittance, namely 93.7%, and a root-mean-square (RMS) roughness of 1.63 nm. Therefore, thin-film transistors (TFTs) with a Zn_0.8Mg_0.2O active channel layer were fabricated and found to have n-type enhancement mode. The Zn_0.8Mg_0.2O TFT had a field-effect mobility of 0.1 cm²/V s, threshold voltage of 6.0 V, and drain current on/off ratio of more than 10⁷.