Three‐dimensionally braided carbon fiber–epoxy composites,a new type of material for osteosynthesis devices. I. Mechanical properties and moisture absorption behavior

In recent years, three‐dimensionally (3D) braided composites have attracted a great deal of attention because of their high‐impact damage tolerance and fatigue life, superior fracture toughness, and so forth, and have been used in aeronautics, military, and transportation. These advantages make them strong candidates for osteosynthesis devices. In this study, 3D braided carbon fiber–epoxy (C_3D/EP) composites were produced via a simple vacuum impregnation technique. The load‐deflection curve, mechanical properties, and influence of fiber volume fraction, braiding angle, and axial reinforcing fibers were examined to determine their suitability for internal fixation devices. It is found that the C_3D/EP composites have excellent toughness and do not show brittleness when fractured because of their relatively high void content. The flexural, shear, and impact strengths of the C_3D/EP composites are excellent. It was shown that a C_3D/EP composite with a stiffness similar to load‐bearing bones can be made while maintaining enough strength. It is concluded that a relatively higher void content and braiding angle is more suitable for the C_3D/EP composites from the viewpoint of requirements of fracture fixation materials. The moisture absorption behavior and changes in mechanical properties caused by moisture uptake were evaluated. Results show that absorbed moisture slightly decreases mechanical properties of the C_3D/EP composites. Contrary to the unreinforced epoxy, the moisture absorption behavior of the C_3D/EP composites cannot be described with Fick's law of diffusion, probably because of the presence of voids and/or 3D fiber structure. The exact mechanisms should be proposed in further investigations. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 1031–1039, 2002     

ATM技术在校园网中的实时性应用

讨论了ＡＴＭ论坛关于局域网仿真技术的基本思想及其协议体系的工作过程，并介绍了利用局域网仿真技术在校园网中应用ＡＴＭ技术实现视频传输的方法。     

Effects of substrate temperature and texturing on the magnetic properties and crystallographic structures of CoCrTa/Cr thin film

Bi-layer CoCrTa/Cr films were deposited on textured aluminium or textured NiP-plated aluminium substrate by d.c. magnetron sputtering. The crystal anisotropy and thereby magnetic properties depending on substrate material, substrate temperature and texturing, were investigated. The magnetic crystal anisotropy induced by the mechanical texture on aluminium or NiP/Al substrates along the texture lines for the film deposited at high temperature, were clearly observed, while the film deposited at low temperature shows less prominent anisotropic behaviour. X-ray diffraction analysis indicates a change in the preferred orientation of the chromium and CoCrTa films sputtered on different substrates at different temperatures. It was found that a high substrate temperature was beneficial to the formation of Cr(002) and therefore epitaxial growth of Co(11¯20) on Cr(002) for either aluminium or NiP/Al substrates.     

Singular value properties of LQ regulators

The closed-loop singular values of an LQ regulator transfer function are proved to be no greater than the singular values of the open-loop transfer function and, in the case of output-weighted cost function, to be no greater than the output-weighting parameter     

国内外改质沥青生产的现状及其发展

煤焦油沥青是炼铝及碳素工业的重要原料之一，它地质量如何直接影响到制品的技术经济指标。近年来，随着科学技术的发展，煤焦油沥青重整改质技术引起重视。目前已有许多国家已生产出改质沥青来满足制取电炉炼钢超高功率电极以及制品铝电解板的要求证同国内对此也开始进行研制工作。介绍了国内外改质沥青生产的现状及发展，并提出了参考建议。     

钨铜合金药型罩及其性能

钨铜合金药型罩的应用可以提高射流对均质钢靶的侵彻能力.这一提高得益于射流密度的提高以及断裂时间的延长. 本文对钨铜合金射流及其断裂形态通过X光照像进行了研究.它的旋转效应及其炸高特性也进行了实验研究. 钨铜合金药型罩的威力实验在φ30 mm的破甲弹上进行.在相同装药条件下与紫铜罩相比,威力提高20～30%.     

联合法制备VBL萤光增白剂－砍两头新工艺

将ＤＳＤ酸生产中还原反应并经中和过滤后的清液直接用于ＶＢＬ萤光增白剂生产，获得满意的效果。     

Scattering parameters of a waveguide cross junction loaded with a metallic post in the center

In this paper, the scattering parameters of a waveguide cross junction loaded with a metallic post in the center are analyzed for the first time by using the Method of Lines. The homogeneous boundary condition of the third kind and curved boundary are introduced in the formulation. Numerical results are in good agreement with the experimental data. The scattering parameters at Ka-band and W-band of the cross junctions loaded with metallic posts of different radii are presented. It is shown from the numerical results that loaded with metallic posts is an effective means for adjusting the network parameters of the waveguide cross junction to satisfy some special requirements in the design of millimeter wave components.