Preparation and optical properties of CdxHg1-xTe doped silica glass

In this paper, the Cd_xHg_1-xTe (x=1-0.7) doped silica glass was prepared through two step sol-gel process and in-situ growth technique from tetraethoxysilane (TEOS), cadmium acetate, mercury acetate and telluric acid. The influence of various factors on the glass was studied. The structure of the microcrystals was investigated by XRD. The absorption and transmittance spectrum of the composite showed that the shift of absorption edge was in conformity with the quantum size effect. The third-order nonlinear optical susceptibility χ⁽³⁾ was measured by the degenerate four wave mixing (DFWM). The values of χ⁽³⁾ was in the range of 10^-11-10^-12 MO esu at wavelength of 1.06 μm.     

土钉支护结构水平位移安全监控模型研究

国内现行规范、标准是以极限变形值作为土钉支护结构水平位移安全监测报警值 ,但没有反映工程进度影响 ,不便指导工程实践。提出“过程控制”概念 ,以反正切函数为基本形式 ,基于历史经验建立“安全时程曲线”控制模型 ,要求施工过程中实测水平位移始终处在“安全时程曲线”之下 ,以确保最终变形在某一适当的阈值之内 ,已有实测结果可以为施工方案调整提供依据。通过实际案例 ,检验模型的可行性 ,表明过程控制模型较极限变形策略更具可操作性     

Application of asymptotic waveform evaluation to eigenmode expansion method for analysis of simultaneous switching noise in printed circuit boards (PCBs)

In this paper, the asymptotic waveform evaluation (AWE) technique is first applied to the conventional eigenmode expansion method for characterizing a power/ground (P/G) plane pair and analyzing the simultaneous switching noise on such plane pairs for printed circuit boards or multichip modules. The application of AWE avoids a large number of iterations in computing the impedance frequency response of a P/G plane pair structure and greatly reduces the computation time. Meanwhile, to obtain an accurate solution in an entire frequency range, we employ the complex frequency hopping technique which can help select multiple expansion points. In addition, the proposed approach can also be used to characterize the P/G plane pair structures with irregular shapes. Three examples demonstrate its high efficiency and good accuracy.     

Low RF noise and power loss for ion-implanted Si having an improved implantation process

Very-low-transmission line noise of <0.25 dB at 18 GHz and low power loss /spl les/0.6 dB at 110 GHz have been measured on transmission lines fabricated on proton-implanted Si. In contrast, a standard Si substrate gave much higher noise of 2.5 dB and worse power loss of 5 dB. The good RF integrity of proton-implanted Si results from the high isolation impedance to ground, as analyzed by an equivalent circuit model. The proton implantation is also done after forming the transmission lines at a reduced implantation energy of /spl sim/4 MeV. This enables easier process integration into current VLSI technology.     

Non‐reflecting artificial boundaries for transient scalar wave propagation in a two‐dimensional infinite homogeneous layer

This paper presents an exact non‐reflecting boundary condition for dealing with transient scalar wave propagation problems in a two‐dimensional infinite homogeneous layer. In order to model the complicated geometry and material properties in the near field, two vertical artificial boundaries are considered in the infinite layer so as to truncate the infinite domain into a finite domain. This treatment requires the appropriate boundary conditions, which are often referred to as the artificial boundary conditions, to be applied on the truncated boundaries. Since the infinite extension direction is different for these two truncated vertical boundaries, namely one extends toward x →∞ and another extends toward x→‐ ∞, the non‐reflecting boundary condition needs to be derived on these two boundaries. Applying the variable separation method to the wave equation results in a reduction in spatial variables by one. The reduced wave equation, which is a time‐dependent partial differential equation with only one spatial variable, can be further changed into a linear first‐order ordinary differential equation by using both the operator splitting method and the modal radiation function concept simultaneously. As a result, the non‐reflecting artificial boundary condition can be obtained by solving the ordinary differential equation whose stability is ensured. Some numerical examples have demonstrated that the non‐reflecting boundary condition is of high accuracy in dealing with scalar wave propagation problems in infinite and semi‐infinite media. Copyright © 2003 John Wiley & Sons, Ltd.     

Apply geometric duality to energy-efficient non-local phenomenon awareness using sensor networks

A powerful concept to cope with resource limitations and information redundancy in wireless sensor networks is the use of collaboration groups to distill information within the network and suppress unnecessary activities. When the phenomena to be monitored have large geographical extents, it is not obvious how to define these collaboration groups. This article presents the application of geometric duality to form such groups for sensor selection and non-local phenomena tracking. Using a dual-space transformation, which maps a non-local phenomenon (e.g., the edge of a half-plane shadow) to a single point in the dual space and maps locations of distributed sensor nodes to a set of lines that partitions the dual space, one can turn off the majority of the sensors to achieve resource preservation without losing detection and tracking accuracy. Since the group so defined may consist of nodes that are far away in physical space, we propose a hierarchical architecture that uses a small number of computationally powerful nodes and a massive number of power constrained motes. By taking advantage of the continuity of physical phenomena and the duality principle, we can greatly reduce the power consumption in non-local phenomena tracking and extend the lifetime of the network.