Synthesis and electrochemical properties of Th-doped LiMn2O4 powders for lithium-ion batteries

To improve the cycle performance of eco-friendly and cost-effective spinel LiMN2O4 as the Li secondary batteries, the Th-doped LiThxMn1-xO4 spinel powers were synthesized by solid-state method. The starting materials, Li2CO3,MnO2 and Th(NO3)4·4H2O, were mixed uniformly using a traditional ball milling, which resulted in a uniform particle size distribution in the mixed powers. Tests of X-ray diffraction, SEM, impedance spectra and charge-discharge were carried out for LiThxMn1-xO4 cathode materials. Results show that the synthesized LiTh0.01Mn1.99O4 material exhibits standard spinel structure, regular particle morphology and excellent property of charge-discharge for big current. The capacity retention of the material modified by doping Th is more than 85.1% of the first discharge specific capacity of 111.5 mAh·g -1 after 20 cycles at the current rate 1C, while the pristine LiMN2O4 is only 57% of the first discharge specific capacity of 110.2 mAh·g-1 after the same cycles at the same current rate.     

Ambient temperature cured TiB_2 cathode coating for aluminum electrolysis

1　INTRODUCTIONAluminumindustryhasbeendevelopingrapidlyinChinainrecentyears ,soderbergcellshavebeenre placedwithmodernprebakecellsinmanyaluminumsmelters,theaveragecelllifehowever ,forprebakecellsinourcountrywasonlyabout130 0d ,muchlowerthantheaveragecelllife ,i.e .above 2 5 0 0d ,forthecellsindevelopedcountries .TiB2 cathodecoating (TCC)couldbeoneofthesolutionstoreducegreatlytheopportunitytotheearlyfailureofcellsandextendthecelllifeofprebakecell[14 ] .Theconceptoftitaniumdiboride (TiB2 …     

冷却条件对超级钢钨极氩弧焊焊接接头组织性能的影响

采用钨极氩弧焊焊接方法对400MPa级超级钢进行焊接，并对焊后空冷和水冷两种冷却条件下的焊接接头进行了组织性能分析。研究结果表明，水冷条件下，其接头的综合力学性能要优于空冷条件，可以应用与实际生产。     

铝合金特殊焊接模式的研究

对铝合金汽车储液干燥罐环缝焊接进行了研究，提出了特殊的焊接模式，并对焊接电流及焊接速度进行优化，得出焊接结果。     

铁精矿粒度对球团强度的影响

以大红山、曼南坎和滇滩等精矿的粒度以及膨润土用量和润磨时间为因子,以生球落下强度、生球爆裂温度、预热球抗压强度和焙烧球抗压强度为评价指标,进行了五因子二次回归组合实验研究。结果表明:随着铁精矿小于0.074mm粒级含量的增加,生球爆裂温度下降,预热球和焙烧球抗压强度提高;当铁精矿小于0.074mm粒级含量小于75%(质量分数)时,生球落下强度逐渐上升,当小于0.074mm粒级含量为75%时,生球落下强度达到最大值,之后有下降趋势。并不是铁精矿粒度越细球团强度就会越好,铁精矿粒度还应该满足一个合适的粒度组成。     

Application of an analytical phase transformation model

Employing isothermal and isochronal differential scanning calorimetry, an analytical phase transformation model was used to study the kinetics of crystallization of amorphous Mg82.3Cu17.7 and Pd40Cu30P20Ni10 alloys. The analytical model comprised different combinations of various nucleation and growth mechanisms for a single transformation. Applying different combinations of nucleation and growth mechanisms, the nucleation and growth modes and the corresponding kinetic and thermodynamic parameters, have been determined. The influence of isothermal pre-annealing on subsequent isochronal crystallization kinetics with the increase of pre-annealing can be analyzed. The results show that the changes of the growth exponent, n, and the effective overall activation energy Q, occurring as function of the degree of transformation, do not necessarily imply a change of nucleation and growth mechanisms, i.e. such changes can occur while the transformation is isokinetic.     

Nb微合金化建筑钢筋微观组织与屈服行为的关系

采用力学拉伸试验、显微组织观察等手段，对屈服平台长度不同的Nb微合金化建筑钢筋进行了金相组织定量分析，并对无屈服平台的试样进行了时效处理。结果表明：贝氏体含量影响着钢筋屈服平台的变化；随贝氏体含量的增大，钢筋屈服平台长度逐渐缩短直至消失；一定温度下，长时间的时效保温处理可使得钢筋的屈服平台得以恢复。在此基础上，讨论了贝氏体的影响机理、生成原因以及改善措施。     

基于有限元的大型铝型材拉伸矫直设备设计方法研究

介绍了大型铝型材拉伸矫直设备的研究现状,分析了现有拉伸矫直设备的缺点,提出并设计了新型的大型铝型材拉伸矫直设备。采用有限元数值模拟方法,对大型铝型材拉伸矫直机的关键零部件受力变形状况进行了数值模拟,得到了设备关键零部件如拉伸头、移动横梁等的应力和应变分布情况,并对结构进行了优化。此种方法降低了设备制造成本,提高了设备的精度和刚度。生产实践表明:采用此方法设计的拉伸矫直机运行平稳可靠。     

新型纸张水分计算机检测系统的研究

介绍了新型纸张水分计算机检测系统的检测原理，检测系统的硬件配置。运用VC 6.0开发工具，对系统进行串行通信和控制软件的设计。     

EFFECT OF TRACE Cr ON PRECIPITATION AND MICROSTRUCTURAL PARAMETERS OF A COMMERCIAL PURITY Al-5.0Zn-1.8Mg ALLOY

本文利用硬度、显微镜和透射电镜系统地研究了微量Cr对工业纯Al-5.0Zn-1.8Mg合金的沉淀过程、临界形核温度T_c~′和组织参数的影响。结果表明,Cr是促进不均匀沉淀和提高T_c~′温度的元素。低温时效(T_a≤160℃)能抑制晶界沉淀桕(GBP)、无沉淀带(PFZ)和基体沉淀相(MPt)的长大;但高温时效(T_a≥180℃)它又能促进这些参数的强烈长大。这些变化特点,可用Cr与过剩空位交互作用的双重性机理来说明。