太赫兹脉冲焦平面成像技术的发展与应用

作为太赫兹技术中的重要组成部分,太赫兹脉冲焦平面成像一经问世就引起了行业内的广泛关注,人们引入了各种方法去提升此成像技术的测量性能,同时也尝试将此成像技术应用于不同的工业和基础研究领域。本文综述了近年来人们对太赫兹脉冲焦平面成像的技术改良和应用研究,包括提升成像系统的空间分辨率、信噪比、信息获取能力,以及将此成像技术应用于光谱识别检测、超表面器件功能验证、太赫兹特殊光束测量、太赫兹表面波观测等,希望该综述能够推动太赫兹脉冲焦平面成像的进一步技术革新和应用拓展。     

Corrosion morphology of AZ91D exposed in an atmospheric environment

The focused ion beam technique was employed to investigate the atmospheric corrosion morphology of AZ91D. It was found that the α matrix of the alloy was preferentially corroded in the areas adjacent to intermetallic phases. The most interesting finding was that the corrosion products in corrosion cavities were pelletlike, which has never been reported before.     

回热损失对磁斯特林制冷循环制冷率的影响

从铁磁质的磁化强度一般表示式出发，探讨热阻和回热损失对磁斯特林制冷循环性能的影响，导出最大制冷率及其它性能参数。得到了结果适用于以顺磁质为工质的磁斯特林制冷循环。并指出在理想回热条件下的结论也适用于磁卡诺制冷循环。     

Kinetics of two-step anionic polymerization

This article deals with the kinetics of two-step anionic polymerization by way of a non-steady state method. Several molecular parameters can be evaluated using the formulae developed. A bimodal molecular weight distribution function for the resulting polymer is derived from the set of kinetic differential equations, which is in agreement with the experimental data reported.     

心电地图仪中工频干扰的一种滤除方法

在心电地图仪中记录到的体表心电信号往往由于电磁的影响而引进工频干扰．基于体表心电信号中工频干扰的特点，作者提出了一种滤除工频干扰的方法，即就单独—胸导联信号通过提高频谱的分辨率来估计工频干扰的频率；基于最小均方误差准则来估计各导联信号中工频干扰的幅度和相位。文中还给出了该算法的流程图和滤波性能分析。模拟结果表明了该算法的有效性。应用该算法对心电地图仪中的工频干扰进行对消，取得了满意的结果。     

减压渣油与FCC油浆共炭化的化学组成变化

考察了齐鲁石化胜利炼油厂催化油浆（FCC）和胜利减压渣油（VR）在490℃，0.8MPa下不同混合比的原料和不同反应时间的中间产物的HS、TS、PS、P及其1h中间产物的HS和TS的^1H-NMR。数据结果反映了体系的反应速度。掺入FCC油浆抑制了VR的反应活性，降低了体系的反应速度，增加了基质的溶解度；1h中间产物的组成结构更接近于原料及反应体系的反应性和基质的溶解度；1h中间产物的芳香度越高，取代基越少，侧链越短，基质对VR中的活性反应组分在炭化早期生成的高度缩合物质的溶解度越大。     

A new efficient method for one‐pot conversions of aryl carboxylic acids into nitriles without solvent

A new efficient method for synthesising nitriles, important organic reagents, is reported in this paper. In an environmentally benign solvent‐free system, aryl carboxylic acids were converted into the corresponding nitriles via one‐pot reactions, by amidation with ethyl carbamate followed by dehydration with thionyl chloride, in excellent yields. The results showed that the method has the advantages of lower cost, higher yield, less pollution and greater ease of work‐up. Copyright © 2008 Society of Chemical Industry     

Amorphous diffusion bonding of steel pipe and its impact toughness

An iron-based amorphous foil (FeNiCrSiB) was used as an interlayer for the amorphous diffusion bonding of low carbon steel pipes under argon flux. The microstructure and mechanical properties of the joint were analyzed using an electron probe micro-analyzer (EPMA), tensile test, bending test and impact test. The results show that the joint microstructure resembles that of the base metal and no precipitates form at the joint. Melting point depressants (B, Si) diffuse far away from the joint and the base metal element is homogenous across the joint. The joint impact toughness is greater than the base metal toughness and the mechanical properties of the joint are similar around the pipe.     

Preparation and photochromism of nanocomposite thin film based on polyoxometalate and polyethyleneglycol

A photochromic nanocomposite based on Keggin structure phosphomolybdic acid (PMoA) well dispersed in polyethyleneglycol (PEG) was fabricated. TEM image showed that PMoA nanoparticles with narrow size distribution were finely dispersed in polymer matrix. FT-IR results showed that the Keggin geometry of polyoxometalates was still preserved inside the composites and strong coulombic interaction was built between PMoA and polymer matrix. Under UV irradiation, the film was reduced photochemically to yield a blue species, which was in accordance with a charge-transfer mechanism.