Performance evaluation of anti-radiation based on the gamma degradation process

In the environment of space radiation, the high-energy charged particles or high-energy photons acting on a spacecraft can cause either temporary device degradation or permanent failure. The traditional probability model is difficult to obtain reliable estimation of unit radiation resistance performance with small samples. Considering that different products will change differently after high-energy particle radiation, we construct a model based on the gamma degradation process. This model can efficiently describe the law of unit radiation resistance variation with the total radiation dose levels under the effect of the total dose and displacement damage. Finally, the proposed model is used to assess the anti-radiation performance of the N-channel power MOSFET device STRH60N20FSY3 produced by STM to obtain average unit radiation resistance, survival probability, survival function, etc.     

Theoretical Investigation of the Viscous Damping Coefficient of Hydraulic Actuators

The viscous damping coefficient(VDC) of hydraulic actuators is crucial for system modeling,control and dynamic characteristic analysis.Currently,the researches on hydraulic actuators focus on behavior assessment,promotion of control performance and efficiency.However,the estimation of the VDC is difficult due to a lack of study.Firstly,using two types of hydraulic cylinders,behaviors of the VDC are experimentally examined with velocities and pressure variations.For the tested plunger type hydraulic cylinder,the exponential model B=αυ~(-β),(α0,β0)or B=α_1e~(-β_1υ)+α_2e~(-β_2υ)(α_1,α_20,β_1,β_20),fits the relation between the VDC and velocities for a given pressure of chamber with high precision.The magnitude of the VDC decreases almost linearly under certain velocities when increasing the chamber pressure from 0.6 MPa to 6.0 MPa.Furthermore,the effects of the chamber pressures on the VDC of piston and plunge type hydraulic cylinders are different due to different sealing types.In order to investigate the VDC of a plunger type hydraulic actuator drastically,a steady-state numerical model has been developed to describe the mechanism incorporating tandem seal lubrication,back-up ring related friction behaviors and shear stress of fluid.It is shown that the simulated results of VDC agree with the measured results with a good accuracy.The proposed method provides an instruction to predict the VDC in system modeling and analysis.     

„Leben machen,sterben lassen“: Palliative Care und Biomacht

Definition of the problem This article takes a critical look at the current theory and practice of palliative care (PC), how it deals with death and dying, and the underlying guiding principle of a good death. Thereby, Foucault’s concept of biopower is utilized. Argument Because PC aims to facilitate a good death, manifold criteria and measures have been developed that help plan interventions and determine their success. In light of the concept of biopower, certain problematic aspects of this development become manifest that usually remain hidden in the bioethical discourse. Conclusion A goal of PC is to improve the quality of life of the dying and therefore not only treats physical symptoms but also psychological, social, and spiritual suffering; thus, it commits itself to maximizing life in a way that can become overdemanding for the individual and possibly does not satisfy the patient’s real needs.     

Oxidation behavior and mechanism of aluminum oxynitride (AlON) at elevated temperatures

The oxidation behavior and mechanism of aluminum oxynitride (AlON) powder exposed to air at elevated temperatures between 800°C and 1300°C was investigated by X-ray diffractometry (XRD), scanning electron microscope (SEM), electron spin resonance (ESR), nuclear magnetic resonance (NMR), and simultaneous thermogravimetry, differential thermal analysis, and mass spectrometry techniques (TG-DTA-MS). The weight of AlON gradually increases to a maximum value at 1150°C and then decreases with further heating. Meanwhile, AlON powder undergoes chemical changes, as evidenced by lattice expansion, and turns eventually into alumina. ESR spectra reveal the occurrence of lone pair electrons in the oxidized products and the intensity of corresponding resonance signal increases before disappearing with the increase in temperature. Combined with the results of NMR and TG-DTA-MS, the measured data suggest that Al-N in [AlO₃N] tetrahedron and [AlO₅N] octahedron are gradually oxidized into Al-O-N group with lone pair electrons, which causes continuous weight gain and lattice expansion. Further oxidation at higher temperatures results in alumina and N₂.     

Engineering all-aromatic polyamide surface from hydrophilic to superhydrophobic and the accelerated strategy

Being a new kind of nanomaterials, aromatic polyamide nanofibers (ANF) have been much highlighted in recent studies. We here demonstrate an isopropyl alcohol (IPA) accelerated chemical cleavage on poly (p-phenylene terephthalamide) chopped fibers, which provides an efficient preparation method of ANF. The comprehensive study on the processes accelerated by different alcohols revealed that the preparation time of ANF in the mixed medium of dimethyl sulfoxide (DMSO)-alcohol (20:1 in volume) was shorten to 45 min and 75 min for methanol (ethanol) and isopropanol, respectively. However, the nanofibers prepared in DMSO-IPA exhibited the minimum in axial and radial dimensions, providing the finest and most uniform diameter of 16 nm. The corresponding ANF films through vacuum assisted filtration also showed the highest tensile strength of 150 MPa, in comparison with those of the ANF films prepared using other alcohols, which were about 110 MPa. Furthermore, ANF/silicon hybrid films were prepared by the ionic ring-opening reaction followed by the alkoxysilane condensation and nanoparticle fabrication. By changing the organo functional groups in the alkoxysilane, the surface of the films were adjustable in a wide contact angle range from 56° (hydrophilic) to 150° (superhydrophobic), suggesting the amendable interfacial properties potential applicable to composite fabrication with most of the resin matrix.     

Self-Diffusion of Iron in Molten Fe-C Alloys

Self-diffusion coefficients of iron in molten Fe-C alloys have been measured by using the capillary method. In addition, the samples have been autoradiographed and sectioned to insure that no significant convection has occurred during the diffusion. The results can be represented by the equation D = 4.3×10^?3 exp (—12.200/RT) for carbon = 4.6 pct and T = 1513° to 1633°K; and D = 1.0×10^?2 exp (—15,700/RT) for carbon = 2.5 pct and T = 1613° to 1673°K. The D values are higher and the heat of activation for diffusion lower in alloys containing more carbon. Calculation based on the Einstein-Stokes equation indicates that the diffusing species is iron ion.     

纳米金刚石的应用

纳米金刚石不仅具有金刚石所固有优异特性，而且还具有纳米材料所拥有的奇异性能。正是这些综合技术特性，使得它在传统的和新的技术领域中得到应用，并初见成效，本文从超精抛光、润滑、复合镀、磁性录音系统和医疗等方面的应用做了扼要的叙述，指出，纳米金刚石颗粒具有球形和准球形的特点，使得摩擦表面形成滚珠轴承效应，而表现出良好的润滑性，从而避免于摩现象的发生，而对一些主要因接触疲劳或高温磨损而失效的工件，纳米金刚石金属的复合涂层，则具有明显的优越性。     

A computational fluid dynamic analysis of gas and particle flow in flame spraying

The flame spraying process, which is a common industrial thermal spraying application, has been analyzed by means of three-dimensional computational fluid dynamics (CFD) simulations. The process used at the Volvo Aero Corporation for the coating of fan and compressor housings has been modeled. The process uses the Metco 6P torch (Metco, Westbury, NY), which ejects a mixture of acetylene and oxygen at high speed through a ring of 16 orifices to form the flame. A stream of argon gas flowing through an orifice in the center of the ring carries a powder of nickel-covered bentonite through the flame to the spray substrate. The torch is cooled by a flow of air through an outer ring of 9 orifices. The simulation emulated reality closely by including the individual inlets for fuel, cooling air, and injected particles. The gas combustion was simulated as a turbulent, multicomponent chemically reacting flow. The standard, two-equation k-ε turbulence model was used. The chemical reaction rates appeared as source terms in the species transport equations. They were computed from the contributions of the Arrhenius rate expressions and the Magnussen and Hjertager eddy dissipation model. The first simulations included several intermediate chemical substances whose predicted concentration agreed favorably with measurements. Later, more simplified simulations incorporated only the global chemical reaction involving the initial and the final products, with corrections to the thermal properties being made to account for the missing intermediaries. The gas velocity and temperature fields predicted by the later simulations compared satisfactorily to those predicted by the earlier, more elaborate, ones. Therefore, the final simulations, which incorporated injected particles, were conducted employing the simplified model with only the global reaction. An in-house finite difference code was developed to calculate particle properties. Allowance was made for elliptical shapes, phase changes, and internal heat transfer with regard to the composite material. The particle velocities and temperatures predicted by the final simulations compared fairly well with experimental results obtained with the optical DPV2000 system.     

硬质合金磨削温度的实验研究

采用半人工和人工热电偶法，对硬质合金YG6和YT30平面磨削的磨削温度进行了实验研究。并对磨削参数与磨削温度的关系，进行了理论分析及实验验证。结果表明：磨削深度和工作台速度增加，磨削温度升高，但工作台速度的改变，对磨削温度的影响较小．