Enhanced thermal stability of a sputtered titanium-nitride film as a diffusion barrier for capacitor-bottom electrodes

The effect of a thin RuO_x layer formed on the Ru/TiN/doped poly-Si/Si stack structure was compared with that on the RuO_x/TiN/doped poly-Si/Si stack structure over the post-deposition annealing temperature ranges of 450–600°C. The Ru/TiN/poly-Si/Si contact system exhibited linear behavior at forward bias with a small increase in the total resistance up to 600°C. The RuO_x/TiN/poly-Si/Si contact system exhibited nonlinear characteristics under forward bias at 450°C, which is attributed to no formation of a thin RuO_x layer at the RuO_x surface and porous-amorphous microstructure. In the former case, the addition of oxygen at the surface layer of the Ru film by pre-annealing leads to the formation of a thin RuO_x layer and chemically strong Ru-O bonds. This results from the retardation of oxygen diffusion caused by the discontinuity of diffusion paths. In particular, the RuO_x layer in a nonstoichiometric state is changed to the RuO₂-crystalline phase in a stoichiometric state after post-deposition annealing; this phase can act as an oxygen-capture layer. Therefore, it appears that the electrical properties of the Ru/TiN/poly-Si/Si contact system are better than those of the RuO_x/TiN/poly-Si/Si contact system.     

热作模具钢表面激光堆焊耐磨合金层的研究

本文主要通过在H13钢上用大功率CO_2激光束进行堆焊,阐述了激光堆焊工艺变化对堆焊组织和性能的影响,在本试验条件下,得到了高密度弥散金属化合物组织的激光堆焊层,平均硬度为HV800,与基体呈冶金结合,耐磨性比H13模具钢提高149%。     

纸浆漂白废水中有机氯化物的排放与控制

本文概述了纸浆漂白废水的特性，以及影响其有机氯化物发生量的因素。     

基于TC8830AF的智能语音卡结构与设计

本文描述一种基于８０３１单片机和ＴＣ８８３０ＡＦ语音处理器的ＰＣ机智能语音卡，通过软硬件设计解决了ＰＣ－８０３１－ＴＣ８８３０ＡＦ结构中的通讯问题。该语音卡在进行语音的合成、编辑和播放时，仅占用极少的ＰＣ机ＣＰＵ处理时间，能满足计算机系统进行实时语音合成的要求。     

GaN and AlGaN high-voltage rectifiers grown by metal-organic chemical-vapor deposition

In this paper, we report the study of the electrical characteristics of GaN and AlGaN vertical p-i-n junctions and Schottky rectifiers grown on both sapphire and SiC substrates by metal-organic chemical-vapor deposition. For GaN p-i-n rectifiers grown on SiC with a relatively thin “i” region of 2 μm, a breakdown voltage over 400 V, and forward voltage as low as 4.5 V at 100 A/cm² are exhibited for a 60-μm-diameter device. A GaN Schottky diode with a 2-μm-thick undoped layer exhibits a blocking voltage in excess of ∼230 V at a reverse-leakage current density below 1 mA/cm², and a forward-voltage drop of 3.5 V at a current density of 100 A/cm². It has been found that with the same device structure and process approach, the leakage current of a device grown on a SiC substrate is much lower than a device grown on a sapphire substrate. The use of Mg ion implantation for p-guard rings as planar-edge terminations in mesageometry GaN Schottky rectifiers has also been studied.     

High-frequency small signal AC and noise modeling of MOSFETs for RFIC design

High-frequency (HF) AC and noise modeling of MOSFETs for radio frequency (RF) integrated circuit (IC) design is discussed. A subcircuit RF model incorporating the HF effects of parasitics is presented. This model is compared with the measured data for both y parameter and f_T characteristics. Good model accuracy is achieved against measurements for a 0.25 μm RF CMOS technology. The HF noise predictivity of the model is also examined with measured data. Furthermore, a methodology to extract the channel thermal noise of MOSFETs from HF noise measurements is presented. By using the extracted channel thermal noise, any thermal noise models can be verified directly. Several noise models including the RF model discussed in this paper have been examined, and the results show that the RF model can predict the channel thermal noise better than the other models     

Fabrication of 1.55 μm VCSELs on Si using metallic bonding

Using AuGeNiCr multilayered metals as the wafer bonding medium, long-wavelength GaInAsP/InP vertical cavity surface emitting lasers employing Al-oxide/Si as the upper and lower distributed Bragg reflectors were fabricated on Si substrate with the bonding interface formed outside the vertical cavity surface emitting laser cavity. Laser emission at 1.545 μm was measured under pulsed operations near room temperature. The low-temperature metallic bonding process demonstrates a great potential in device fabrication     

新型低压抽屉式开关柜在冶金系统的应用

介绍新型低压抽屉式开关柜的结构性能和特点，并与早期低压柜作了比较。阐述了新型低压抽屉式开关柜在冶金系统应用中的几点改进情况。     

A fully soft-switched extended-period quasi-resonantpower-factor-correction circuit

This paper presents the design criteria, procedure, and implementation of a soft-switched power-factor-correction (PFC) circuit based on the extended-period quasi-resonant (EPQR) principles. All power electronic devices including switches and diodes in the circuit are fully soft switched. The design method is demonstrated in a prototype circuit. The operating principles are confirmed with computer simulation and experimental results. A comparison of the EP-QR operation and zero-voltage-transition (ZVT) pulse-width modulation (PWM) method