Thermophysical properties of silicate slags

The optimization of metallurgical processes requires reliable data of the slag phase. This paper focuses on three properties that are relevant to heat and mass-transfer calculations — viscosities,thermal diffusivities, and surface tensions of silicate melts. A brief account of the experimental techniques used for the measurements of these properties, with special reference to the work carried out in the Division of Metallurgy, Royal Institute of Technology, Stockholm, Sweden, are presented, along with the advantages and limitations. As these properties are structure-oriented, the impact of structure on these properties is also presented. The paper is intended as a state-of-the-art review of the subject.     

Formation Mechanism of Porous Alumina With Oriented Cylindrical Pores Fabricated by Unidirectional Solidification

Porous alumina whose pores were aligned in one direction was fabricated by the unidirectional solidification method under a pressurized hydrogen atmosphere. The porous structure is formed at the solid–liquid interface during solidification due to a hydrogen solubility gap at the melting point. The hydrogen gas is dissolved into molten alumina according to Sieverts' law and insoluble gas that corresponds to the amount of solubility gap evolves from the solid phase at the solid–liquid interface during the unidirectional solidification to form the pores. The porosity and pore size of the solidified samples decreased with increasing total pressure where the environmental gas consisted of pure hydrogen or hydrogen–argon mixed gases. There is a reverse proportion relation between the pore diameter and the total pressure according to Boyle's law.     

Effect of Lipase Activity and Specificity on the DAG Content of Olive Oil from the Shodoshima-Produced Olive Fruits

Olive oils have a higher relative diacylglycerol (DAG) content than other plant oils. The lipase in olive fruits is involved in DAG production and is directly related to the acidity of the olive oil. However, the lipase activity and positional selectivity have not been clarified. To investigate the properties of olive fruit lipase, olive fruits of the Mission variety harvested during mid-December of 2005 on Shodoshima Island (Japan) were stored at 20, 30 or 40 °C for 4 weeks. Changes in the acidity and acylglycerol content of the oils extracted from the stored fruits were analyzed. The acidity and DAG content of the olive oils increased due to triacylglycerol (TAG) hydrolysis during storage. sn-1,2-DAGs preferentially increased during the early stages of storage, indicating that the olive fruit lipase is enantioselective for the sn-3 position, while non-enzymatic isomerization of sn-1,2-DAGs was observed throughout the entire duration of storage. Kinetic analysis revealed that the enantioselectivity of olive fruit lipase for the sn-3 position was approximately four times greater than for the sn-1 position. The lipase was gradually inactivated at temperatures of 30 °C or higher, and the ratios of the rate constant for inactivation to TAG hydrolysis at the sn-3 position was 0.2, 13, and 23 at 20, 30, and 40 °C, respectively.     

Adsorption of cationic monomeric and gemini surfactants on montmorillonite and adsolubilization of vitamin E

Adsorption of a cationic gemini surfactant (1,2-bis(dodecyldimethylammonio) ethane dibromide, 12-2-12) and the corresponding monomeric surfactant (dodecyltrimethylammonium bromide, DTAB) on montmorillonite has been characterized with a combination of adsorption isotherm, interlayer spacing and FT-IR spectroscopic data. Adsolubilization of vitamin E into the adsorbed surfactant layers has also been studied. The adsorption isotherm data reveal that the adsorption of the two surfactants is driven by the two factors: one is the cation exchange that occurs on the interlayer basal planes and the other is the hydrophobic interaction between hydrocarbon chains of the surfactants. Although the adsorbed amount measured in the saturation region (in mol g(-1)) is almost identical for the two surfactants, the conformation of the intercalated surfactant molecules differs significantly from each other. The adsorption of DTAB results in a lateral bilayer arrangement in the limited interlayer space, whereas 12-2-12 gives a normal bilayer arrangement in the expanded interlayer space. Adsolubilization of vitamin E takes place into the adsorbed surfactant layers, and interestingly, all the vitamin E molecules added in the montmorillonite suspensions are hybridized at lower surfactant concentrations due to the great specific surface area of the clay material. Since the maximum adsolubilization amount is usually obtained just below the critical micelle concentration, the gemini surfactant is deemed to be more efficient than the corresponding monomeric one to achieve the great adsolubilization amount.     

HCl emission during co-pyrolysis of demolition wood with a small amount of PVC film and the effect of wood constituents on HCl emission reduction

In this study, HCl emission during the co-pyrolysis of demolition wood and a small amount of polyvinyl chloride (PVC) film (the Cl content of which ranged from 0.5% to 6% by weight) in an N₂ atmosphere at elevated temperatures of up to 600 °C was measured using a laboratory-scale cylindrical batch reactor. In the pyrolysis experiments, HCl emission was reduced by the presence of wood. The effect of the primary constituents of wood (cellulose, hemicellulose, and lignin) on HCl emission was investigated by not only measuring HCl emission and Cl distribution to various phases during the co-pyrolysis of each constituent with PVC film but also by conducting thermogravimetric analysis of the constituents. This investigation first revealed that hemicellulose significantly reduced HCl emission by fixing most of the Cl molecules in a sample into pyrolyzed residue.     

Evaluation of surfactant-aided degumming of vegetable oils by membrane technology

The first step in the process of vegetable oil refining is degumming, in which phospholipids and mucilaginous gums are removed that otherwise result in a low-grade oil. A membrane process is remarkably simple yet potentially offers many advantages in degumming. Studies were conducted on surfactant-aided membrane degumming with soybean and rapeseed oils in a magnetically stirred flat membrane batch cell with different types of microfiltration membranes. The reduction of phospholipids in soybean oil was in the range of 85.8–92.8% during the membrane process. The phosphorus content of membrane permeates of soybean oil was in the range of 20–58 mg/kg. Crude rapeseed oil contained higher amount of nonhydratable phospholipids and hence resulted in lower reduction in phospholipids, in the range of 66.4–83.2%. Addition of hydratable phospholipids could improve the efficiency of degumming in the membrane process without using any electrolyte, resulting in improvement of quality as well as quantity of the phospholipids.     

Fabrication and electrical properties of SrTiO3/diamond junctions

Strontium titanate (STO) films were directly deposited on Ib (100) single crystal diamond by r.f. magnetron sputtering. The as-deposited STO film was in amorphous state. On the other hand, the crystalline STO film was obtained under the optimized condition of a deposition temperature of 250 °C and a post-annealing temperature of 650 °C. STO/diamond junctions were fabricated on boron-doped homoepitaxial layers grown on p⁺-type single crystal diamond substrates. Electrical properties of the STO/diamond junction were investigated by changing the surface terminations of diamond with hydrogen or oxygen and the crystallinity of the STO film. It was found that the amorphous STO acted like a semi-insulator on H-diamond surface and that the amorphous STO/O-diamond junction behaved like a Schottky diode. The crystalline STO/O-diamond showed a complex rectifying behavior. The crystalline STO film possessed a higher dielectric constant as compared to that of the amorphous one.     

Fundamental study of welding with a 1 kW YAG laser beam transmitted by optical fibre

Summary

This paper describes an in-process monitoring system developed to monitor the quality of CO₂ laser welding. It incorporates two photo sensors aligned at different angles to detect the long-term power stability as well as underfill and pitting defects and has been used on a production line for tailored blank welding of automotive parts since 1993. The laser power stability can be monitored by long-term recording of the average plasma emission intensity. Underfills can be sensitively recognised by a decrease in the light emission intensity detected by the low angle sensor, since the hot core of the plasma plume is hidden by the surrounding material. Small pits can be detected by a sharp decrease in the light emission intensity recorded by the high angle sensor.     

Automatic electron beam alignment adjustment system and automatic filament current adjustment system for electron beam welder

Recently, the electron beam welders with high acceleration voltage (more than 100 kV) and high electrical power (more than 15 kW) have been reviewed the role of the high-energy electron beam density again, due to space or aircraft development or automobile industry desired high productivity and high accurate welding for saving energy. NEC group have supplied these electron beam welders. This time, the automatic alignment adjustment system of the electron beam orbit and the automatic adjustment system of filament current were developed and put to a practical use. As a result, the great effectiveness for the stability of welding quality was apparent.     

An Engineered Biliverdin-Compatible Cyanobacteriochrome Enables a Unique Ultrafast Reversible Photoswitching Pathway

Cyanobacteriochromes (CBCRs) are promising optogenetic tools for their diverse absorption properties with a single compact cofactor-binding domain. We previously uncovered the ultrafast reversible photoswitching dynamics of a red/green photoreceptor AnPixJg2, which binds phycocyanobilin (PCB) that is unavailable in mammalian cells. Biliverdin (BV) is a mammalian cofactor with a similar structure to PCB but exhibits redder absorption. To improve the AnPixJg2 feasibility in mammalian applications, AnPixJg2_BV4 with only four mutations has been engineered to incorporate BV. Herein, we implemented femtosecond transient absorption (fs-TA) and ground state femtosecond stimulated Raman spectroscopy (GS-FSRS) to uncover transient electronic dynamics on molecular time scales and key structural motions responsible for the photoconversion of AnPixJg2_BV4 with PCB (Bpcb) and BV (Bbv) cofactors in comparison with the parent AnPixJg2 (Apcb). Bpcb adopts the same photoconversion scheme as Apcb, while BV4 mutations create a less bulky environment around the cofactor D ring that promotes a faster twist. The engineered Bbv employs a reversible clockwise/counterclockwise photoswitching that requires a two-step twist on ~5 and 35 picosecond (ps) time scales. The primary forward P_fr → P_o transition displays equal amplitude weights between the two processes before reaching a conical intersection. In contrast, the primary reverse P_o → P_fr transition shows a 2:1 weight ratio of the ~35 ps over 5 ps component, implying notable changes to the D-ring-twisting pathway. Moreover, we performed pre-resonance GS-FSRS and quantum calculations to identify the Bbv vibrational marker bands at ~659,797, and 1225 cm⁻¹. These modes reveal a stronger H-bonding network around the BV cofactor A ring with BV4 mutations, corroborating the D-ring-dominant reversible photoswitching pathway in the excited state. Implementation of BV4 mutations in other PCB-binding GAF domains like AnPixJg4, AM1_1870g3, and NpF2164g5 could promote similar efficient reversible photoswitching for more directional bioimaging and optogenetic applications, and inspire other bioengineering advances.