Effect of changing groundwater levels caused by land-use changes on greenhouse gas fluxes from tropical peat lands

Monthly measurements of carbon dioxide (CO₂), methane (CH₄) and nitrous oxide (N₂O) fluxes in peat soils were carried out and compared with groundwater level over a year at four sites (drained forest, upland cassava,upland and lowland paddy fields) located in Jambi province, Indonesia. Fluxes from swamp forest soils were also measured once per year as the native state of this investigated area. Land-use change from drained forest to lowland paddy field significantly decreased the CO₂ (from 266 to 30 mg C m^–2 h^–1) and N₂O fluxes (from 25.4 to 3.8 g N m^–2 h^–1), but increased the CH₄ flux (from 0.1 to 4.2 mg C m^–2 h^–1) in the soils. Change from drained forest to cassava field significantly increased N₂O flux (from 25.4 to 62.2 g N m^–2 h^–1), but had no significant influence on CO₂ (from 266 to 200 mg C m^–2 h^–1) and CH₄ fluxes (from 0.1 to 0.3 mg C m^–2 h^–1) in the soils. Averaged CO₂ fluxes in the swamp forests (94 mg C m^–2 h^–1) were estimated to be one-third of that in the drained forest. Groundwater levels of drained forest and upland crop fields had been lowered by drainage ditches while swamp forest and lowland paddy field were flooded, although groundwater levels were also affected by precipitation. Groundwater levels were negatively related to CO₂ flux but positively related to CH₄ flux at all investigation sites. The peak of the N₂O flux was observed at –20 cm of groundwater level. Lowering the groundwater level by 10 cm from the soil surface resulted in a 50 increase in CO₂ emission (from 109.1 to 162.4 mg C m^–2 h^–1) and a 25% decrease in CH₄ emission (from 0.440 to 0.325 mg C m^–2 h^–1) in this study. These results suggest that lowering of groundwater level by the drainage ditches in the peat lands contributes to global warming and devastation of fields. Swamp forest was probably the best land-use management in peat lands to suppress the carbon loss and greenhouse gas emission. Lowland paddy field was a better agricultural system in the peat lands in terms of C sequestration and greenhouse gas emission. Carbon loss from lowland paddy field was one-eighth of that of the other upland crop systems, although the Global Warming Potential was almost the same level as that of the other upland crop systems because of CH₄ emission through rice plants.     

HamleDT: Harmonized multi-language dependency treebank

We present HamleDT—a HArmonized Multi-LanguagE Dependency Treebank. HamleDT is a compilation of existing dependency treebanks (or dependency conversions of other treebanks), transformed so that they all conform to the same annotation style. In the present article, we provide a thorough investigation and discussion of a number of phenomena that are comparable across languages, though their annotation in treebanks often differs. We claim that transformation procedures can be designed to automatically identify most such phenomena and convert them to a unified annotation style. This unification is beneficial both to comparative corpus linguistics and to machine learning of syntactic parsing.     

Virtual target tracking of mobile robot and its application to formation control

A virtual target tracking approach is proposed for kinematic control of mobile robot. In the controller, linear and angular velocity inputs are generated by using the local data of robot position and orientation along with the estimated velocity of target object. Applying the proposed approach to a cooperative robot group with arbitrary number of multiple mobile robots, it is possible to create various robot formations for cooperative navigation and tracking of moving object. The developed controller is shown to be stable and convergent through theoretical proof and a series of experiments.     

Chaotic fluid mixing by alternating microparticle topologies to enhance biochemical reactions

We report experimental results on chaotic mass transport induced by alternating topological changes of magnetic particle chains actuated by a rotating magnetic field. Results on the induced fluid flows, through particle tracing experiments and mixing experiments, are obtained for (1) the regime of rigid chain rotation and (2) the regime wherein chains periodically fragment and reform. In the case of rigid rotating chains, the overall tracer particle trajectories are steady, slightly modulated circles around the center of the microparticle chains. In the regime of periodic chain breaking and reformation, the tracer particle trajectories become chaotic. The level of mixing is measured by using a mixing index (M) in a water–dye system, i.e., in a perfectly mixed system M = 0, while in an unmixed system M = 1. When particle chains periodically break and reform, we observe that the mixing index M decreases from 1 to 0.1 within 15 rotational cycles. For rigid rotating chains, M reaches a minimum of only 0.5. We also report the effect of the different actuation regimes on a biological binding reaction in the solution and indeed found that the reaction product (at equal actuation time) is significantly enhanced (3 times) by the dynamic chain regime as compared to the rigid chain regime. We conclude that the alternating topological change of microparticle chains—with repetitive chain breakup and chain reformation—is an effective mechanism to achieve chaotic mixing and thereby promote and homogenize reactions in lab-on-a-chip systems.     

A microfluidic optical beam steerer

This paper reports the fabrication and characterization of a prototype microfluidic device that can act as a periodic beam steerer. The prototype is formed by a simple T-junction followed by a serpentine channel that allows generation of a periodical segmented flow of air and water bubbles. If light hits the channel wall with a suitable angle, it can be either transmitted or reflected by the segmented flow, giving rise to an alternating beam steerer. The duty cycle, switching frequency, and overall stability and reproducibility of this prototype system are presented and discussed.     

Leakage current in a Si-based nanopore structure and its influence on noise characteristics

We have measured leakage current in a silicon substrate-based nanopore membrane device immersed in an aqueous environment which typically shows the current level of few nA. This current level is compared with the measured current density (400 nA/cm² at 1 V) from the pristine Si wafer (p-type, 10¹⁶/cm³ boron doping) indicating that the exposed Si surface in a nanopore membrane device acts as an electrochemical reaction site. The leakage current is drastically reduced from >10 nA to <100 pA at 1 V by the deposition of a dielectric layer to the Si-based nanopore membrane device. We also noted that the root-mean-square noise of the ionic current is also reduced from 38 to 28 pA in correlation with the reduction of leakage current, indicating that electrochemical reaction provides one of the major sources of noise.     

Induced-charge electro-osmosis of polymer-containing fluid around a metallic rod

Induced-charge electro-osmotic (ICEO) flow of polymer-containing electrolyte solution around a cylindrical gold-coated stainless steel rod under AC electric field is measured by micro-particle image velocimetry (micro-PIV) for the first time. The ICEO flows as functions of the amount of non-ionic PEG (polyethylene glycol), cationic PDADMA (polydiallyldimethylammonium chloride), and anionic PVSASS (polyvinylsulfonic acid sodium salt) polymers added into the salt solution, frequency, and strength of the AC electric field are measured. The ICEO flow of polymer-containing fluid around the rod is quadrupolar with four vortices and is proportional to the square of imposed electric field. The ICEO flow velocity exponentially decreases with an increased concentration of neutral PEG. Ionic polyelectrolytes significantly increase ICEO velocities due to the enriched net charge within the induced electric double layer arising from the electrostatic interaction between the polarized rod’s surface and the charged polyelectrolytes in ionic polymer solution. In addition, polymer concentration affects the dependence of the ICEO flow on the frequency of AC electric field.     

Investigation and improvement of reversible microfluidic devices based on glass–PDMS–glass sandwich configuration

Reversibly assembled microfluidic devices are dismountable and reusable, which is useful for a number of applications such as micro- and nano-device fabrication, surface functionalization, complex cell patterning, and other biological analysis by means of spatial–temporal pattern. However, reversible microfluidic devices fabricated with current standard procedures can only be used for low-pressure applications. Assembling technology based on glass–PDMS–glass sandwich configuration provides an alternative sealing method for reversible microfluidic devices, which can drastically increase the sealing strength of reversibly adhered devices. The improvement mechanism of sealing properties of microfluidic devices based on the sandwich technique has not been fully characterized, hindering further improvement and broad use of this technique. Here, we characterize, for the first time, the effect of various parameters on the sealing strength of reversible PDMS/glass hybrid microfluidic devices, including contact area, PDMS thickness, assembling mode, and external force. To further improve the reversible sealing of glass–PDMS–glass microfluidic devices, we propose a new scheme which exploits mechanical clamping elements to reinforce the sealing strength of glass–PDMS–glass sandwich structures. Using our scheme, the glass–PDMS–glass microchips can survive a pressure up to 400 kPa, which is comparable to the irreversibly bonded PDMS microdevices. We believe that this bonding method may find use in lab-on-a-chip devices, particularly in active high-pressure-driven microfluidic devices.     

Synthesis and properties of acrylonitrile-CR-methyl methacrylate graft copolymer

Graft copolymerization of acrylonitrile (AN) and methyl methacrylate (MMA) onto polychloroprene (CR) was carried out using benzoyl peroxide as initiator. The effects of mole ratio of AN to MMA, reaction temperature, reaction time, solvent, and initiator concentration on the graft copolymerization were examined. It was found that the thermal stability and weatherability of the AN—CR—MMA graft copolymer (ACM) were considerably better than those of CR.