Pervaporation separation of water/ethanol mixtures through polysaccharide membranes. II. The permselectivity of chitosan membrane

The separation of water/alcohol mixtures through chitosan membrane was investigated. The degree of the deacetylation of chitosan did not affect the selectivity of the membrane in the separation of the water/ethanol mixture. The selectivity of the chitosan membrane was affected by the specific salts such as CoSO₄, ZnSO₄, and MnSO₄ and it increased when the salts were present in the feed mixture or the membrane was pretreated with the salt solution. This behavior would be explained by the contraction of the “holes” produced by the thermal motion of polymer chains and this contraction would be correlated with the conformation change of chitosan molecule due to the formation of complexes with metal ions.     

Facile purification of tocopherols from soybean oil deodorizer distillate in high yield using lipase

Tocopherols have been purified from deodorizer distillate produced in the final deodorization step of vegetable oil refining by a process including molecular distillation. Deodorizer distillate contains mainly tocopherols, sterols, and free fatty acids (FFA); the presence of sterols hinders tocopherol purification in good yield. We found that Candida rugosa lipase recognized sterols as substrates but not tocopherols, and that esterification of sterols with FFA could be effected with negligible influence of water content. Enzymatic esterification of sterols with FFA was thus used as a step in tocopherol purification. High boiling point substances including steryl esters were removed from soybean oil deodorizer distillate by distillation, and the resulting distillate (soybean oil deodorizer distillate tocopherol concentrate; SODDTC) was used as a starting material for tocopherol purification. Several factors affecting esterification of sterols were investigated, and the reaction conditions were determined as follows: A mixture of SODDTC and water (4∶1, w/w) was stirred at 35°C for 24 h with 200 U of Candida lipase per 1 g of the reaction mixture. Under these conditions, approximately 80% of sterols was esterified, but tocopherols were not esterified. After the reaction, tocopherols and FFA were recovered as a distillate by molecular distillation of the oil layer. To enhance further removal of the remaining sterols, the lipase-catalyzed reaction was repeated on the distillate under the same reaction conditions. As a result, more than 95% of the sterols was esterified in total. The resulting reaction mixture was fractionated to four distillates and one residue. The main distillate fraction contained 65 wt% tocopherols with low contents of FFA and sterols. In addition, the residue fraction contained high-purity steryl esters. Because the process presented in this study includes only organic solvent-free enzymatic reaction and molecular distillation, it is feasible as a new industrial purification method of tocopherols. This work was presented at the Biocatalysis symposium in April 2000, held at the 91st Annual Meeting and Expo of the American Oil Chemists Society, San Diego, CA.     

Evaluation of optimum condition for designing high‐performance electro‐driven polymer hydrogel systems

This study investigated a parameter that determines an optimum condition of the content of the ionic group and the concentration of outer solution for high‐performance electro‐driven polymer hydrogel membranes. The optimum condition for quick bending was determined by a simple method that identified the initial conditions based on Donnan equilibrium theory. Since the bending behavior depends on the initial conditions of the ionic group content and the concentration of the outer solution, it can be predicted by the ratio of the ionic concentrations at the membrane–solution interface; the inverse of the Donnan ratio (1/K) at the initial condition. The bending rate of the membranes showed a maximum value at around 1/K = 0.15. The relationship between several interrelated control factors and the bending dynamics of the gel membranes was established by using the initial system parameters alone. 1/K is the effective simple parameter to determine the optimum condition of the content of the ionic group and the concentration of the outer solution for high‐performance membranes. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 111–118, 2000     

Densification and Cell Performance of Gadolinium-Doped Ceria (GDC) Electrolyte/NiO–GDC Anode Laminates

A thin film (60 μm thick) of a gadolinium-doped ceria (GDC) electrolyte was prepared by the doctor blade method. This film was laminated with freeze-dried 42 vol% NiO–58 vol% GDC mixed powder and pressed uniaxially or isostatically under a pressure of 294 MPa. This laminate was cosintered at 1100 °–1500 °C in air for 4–12 h. The laminate warped because of the difference in the shrinkage of the electrolyte and electrode during the sintering. A higher shrinkage was measured for the electrode at 1100 °–1200 °C and for the electrolyte at 1300 °–1500 °C. The increase of the thickness of anode was effective in decreasing the warp and in increasing the density of the laminated composite. The maximum electric power density with a SrRuO₃ cathode using 3 vol% H₂O-containing H₂ fuel was 100 mW/cm² at 600 °C and 380 mW/cm² at 800 °C, respectively, for the anode-supported GDC electrolyte with 30 μm thickness.     

Photocatalytic microreactor study using TiO2-coated porous ceramics

Two kinds of porous ceramic disks, having through-holes with diameters of 0.1 and 0.05 mm, were coated with TiO₂ using two different starting solutions: titanyl(IV)acetylacetonate and a commercial titania sol (STS-01). The morphology of these porous ceramics before and after TiO₂ coating was observed by SEM. The TiO₂-coated porous ceramics were examined as honeycomb photocatalytic microreactors. The photocatalytic activity was evaluated using the decomposition of methylene blue solution for radiation angles of 0° and 10° with respect to the pore axis. The highest photocatalytic activity was obtained for the porous ceramic having the pore diameter of 0.1 mm, coated with titanyl(IV)acetylacetonate and irradiated with a light angle of 0° with respect to the pore axis.     

下一代高密度磁记录介质——L10FePt、CoPt研究进展

垂直磁记录是现今主要的信息存储技术.当前以CoCrPt为记录介质的垂直磁记录已达到密度极限,进一步提高记录密度需要采用磁晶各向异性能更高的材料.L10 FePt、CoPt被认为是下一代高密度磁记录的理想介质材料.本文系统综述了L10 FePt、CoPt记录介质的研究进展.     

“Click Peptide“: pH‐Triggered in Situ Production and Aggregation of Monomer Aβ1–42

Into neutral : We demonstrate the unique features of a pH click peptide based on an O‐acyl isopeptide method. Under acidic conditions, the click peptide remains in a monomeric form. Upon increase of the pH to 7.4, the click peptide is quickly able to convert into Aβ1–42 through an O‐to‐N intramolecular acyl migration. Further study using this pH click peptide would elucidate the pathological role of Aβ1–42 in Alzheimer's disease.

     

Miscibility and Physical Properties of Poly(3‐hydroxybutyrate‐co‐3‐hydroxyhexanoate)/Poly(ethylene oxide) Binary Blends

In order to improve some inferior physical properties of bacterial poly(3‐hydroxybutyrate‐co‐3‐hydroxyhexanoate) [P(3HB‐co‐3HHx)] by blending with PEO, the miscibility, spherulite morphology, crystallization behavior and mechanical properties of P(3HB‐co‐3HHx)/PEO binary biodegradable polymer blends were investigated. A good miscibility between P(3HB‐co‐3HHx) with a 3HHx unit content of 11 mol‐% and PEO in the amorphous state was found when the PEO weight fraction was 10 wt.‐%, while the miscibility decreased dramatically when the PEO weight fraction exceeded 20 wt.‐%. Strongly depending on the blend composition, the mechanical properties of P(3HB‐co‐3HHx) was found to be significantly improved by blending with PEO with a weight fraction of ≈5–17.5 wt.‐%.

     

Synthesis and characterization of fullerene grafted poly(ε‐caprolactone)

The fullerene grafted poly(ε‐caprolactone) (PCL) was successfully synthesized with a graft efficiency of 80%. The fullerene moieties grafted onto the PCL chain aggregate into 1–2 μm particles so that a physical pseudo‐network is formed. Because of the existence of the network structure, the fullerene grafted PCL film can retain its shape at much higher temperatures than that of pure PCL film, as observed in dynamic mechanical tests. It shows a hydrophobic gelling behavior in chloroform solution. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008