Densification and Cell Performance of Gadolinium-Doped Ceria (GDC) Electrolyte/NiO–GDC Anode Laminates

A thin film (60 μm thick) of a gadolinium-doped ceria (GDC) electrolyte was prepared by the doctor blade method. This film was laminated with freeze-dried 42 vol% NiO–58 vol% GDC mixed powder and pressed uniaxially or isostatically under a pressure of 294 MPa. This laminate was cosintered at 1100 °–1500 °C in air for 4–12 h. The laminate warped because of the difference in the shrinkage of the electrolyte and electrode during the sintering. A higher shrinkage was measured for the electrode at 1100 °–1200 °C and for the electrolyte at 1300 °–1500 °C. The increase of the thickness of anode was effective in decreasing the warp and in increasing the density of the laminated composite. The maximum electric power density with a SrRuO₃ cathode using 3 vol% H₂O-containing H₂ fuel was 100 mW/cm² at 600 °C and 380 mW/cm² at 800 °C, respectively, for the anode-supported GDC electrolyte with 30 μm thickness.     

High-Temperature Active Oxidation of Chemically Vapor-Deposited Silicon Carbide in CO─CO2 Atmosphere

Active oxidation behavior of CVD-SiC in CO─CO₂ atmospheres was investigated using a thermogravimetric technique in the temperature range between 1823 and 1923 K. The gas pressure ratio, P _CO2/ P _CO, was controlled between 10⁻⁴ and 10⁻¹ at 0.1 MPa. Active oxidation rates (mass loss rates) showed maxima at a certain value of P _CO2/ P _CO, ( P _CO2/ P _CO )^*, In a P _CO2/ P _CO region lower than the ( P _CO2/ P _CO)^* a carbon layer was formed on the SiC surface. In a P _CO2/ P _CO region higher than the ( P _CO2/ P _CO)^*, silica particles or a porous silica layer was observed on the SiC surface.     

Nano-Blast Synthesis of Nano-size CeO2–Gd2O3 Powders

CeCl₃·7H₂O and GdCl₃·6H₂O that were dissolved in water were precipitated with urea (NH₂CONH₂) to produce matrix agglomerates for three-component nano-reactors. Mixing hexamethylenetetramine with dilute nitric acid resulted in the formation of well-dispersed nano-particles of cyclotrimetilene trinitramine (C₃H₆N₆O₆) (RDX) in the solvent. Nano-reactors were produced by impregnating the nano-C₃H₆N₆O₆ into the matrix agglomerates of an intermediate complex of cerium and gadolinium compounds. Blast initiation of the C₃H₆N₆O₆ resulted in extremely rapid detonation and gaseous products formation at temperatures of 2000°–5000°C, which were compressed into a volume nearly equal to the initial volume of each RDX nano-particle. Multiple "nano-blasts" occurred in the volume of each nano-reactor. The impact of the blast waves led to fragmentation of the surrounding matter. The evolution of a large volume of gaseous products dissipated the heat of the process and limited temperature increase, thus reducing the possibility of local sintering among the primary particles. The short-term high temperature generated during the blasts enhanced the solid solubility of the metal oxides. Uniform aggregates of 22∼74 nm consisting of 6∼14 nm crystallites of gadolinia in ceria solid solution were synthesized.     

Synthesis and electrochemistry of cubic rocksalt Li–Ni–Ti–O compounds in the phase diagram of LiNiO2–LiTiO2–Li[Li1/3Ti2/3]O2

On the basis of extreme similarity between the triangle phase diagrams of LiNiO₂–LiTiO₂–Li[Li_1/3Ti_2/3]O₂ and LiNiO₂–LiMnO₂–Li[Li_1/3Mn_2/3]O₂, new Li–Ni–Ti–O series with a nominal composition of Li_1+z/3Ni_1/2−z/2Ti_1/2+z/6O₂ (0 ≤ z ≤ 0.5) was designed and attempted to prepare via a spray-drying method. XRD identified that new Li–Ni–Ti–O compounds had cubic rocksalt structure, in which Li, Ni and Ti were evenly distributed on the octahedral sites in cubic closely packed lattice of oxygen ions. They can be considered as the solid solution between cubic LiNi_1/2Ti_1/2O₂ and Li[Li_1/3Ti_2/3]O₂ (high temperature form). Charge–discharge tests showed that Li–Ni–Ti–O compounds with appropriate compositions could display a considerable capacity (more than 80 mAh g⁻¹ for 0.2 ≤ z ≤ 0.27) at room temperature in the voltage range of 4.5–2.5 V and good electrochemical properties within respect to capacity (more than 150 mAh g⁻¹ for 0 ≤ z ≤ 0.27), cycleability and rate capability at an elevated temperature of 50 °C. These suggest that the disordered cubic structure in some cases may function as a good host structure for intercalation/deintercalation of Li⁺. A preliminary electrochemical comparison between Li_1+z/3Ni_1/2−z/2Ti_1/2+z/6O₂ (0 ≤ z ≤ 0.5) and Li_6/5Ni_2/5Ti_2/5O₂ indicated that charge–discharge mechanism based on Ni redox at the voltage of >3.0 V behaved somewhat differently, that is, Ni could be reduced to +2 in Li_1+z/3Ni_1/2−z/2Ti_1/2+z/6O₂ while +3 in Li_6/5Ni_2/5Ti_2/5O₂. Reduction of Ti⁴⁺ at a plateau of around 2.3 V could be clearly detected in Li_1+z/3Ni_1/2−z/2Ti_1/2+z/6O₂ with 0.27 ≤ z ≤ 0.5 at 50 °C after a deep charge associated with charge compensation from oxygen ion during initial cycle.     

Modifying ability of Ql-free coal-tar pitch to develop optical anisotropy in co-carbonizations

Carbonization properties of a Ql-free coal-tar pitch (CTP-ASM) prepared by selective precipitation were studied to evaluate it as a source for needle-coke. Its modifying ability for production of needlecoke in co-carbonizations with principal carbonizing substances which gave cokes of mozaic texture in single carbonizations was estimated by changing mixing ratios. The shape and size of the anisotropic optical texture in the co-carbonized coke were measured by point counting. CTP-ASM and Ashland A240, of eight additives, had the highest modifying ability in the co-carbonizations with Khafji vacuum residue. Both contained ca. 6% benzene-insolubles (Bl), and had f_a values of ≈0.9. Other additives of either lower or higher Bl or f_a showed less modifying ability. The modifying susceptibility of principal carbonizing substances varies with their structure and properties. Based on a systematic investigation of co-carbonizations the compatibility between a principal carbonizing substance and an additive is discussed from a viewpoint of their structural parameters.     

Synthesis of High‐Purity Ti3SiC2 by Microwave Sintering

High‐purity ternary laminated compound Ti₃SiC₂ was successfully synthesized by a microwave heating method in the flowing argon for the first time. The mixtures of titanium, silicon, and graphitic carbon (C_gc) or activated carbon (C_ac) with different molar ratios were used to investigate the reaction mechanisms. It was confirmed that Ti₃SiC₂ with high purity of 98 vol.% was achieved without the aids of Al. The optimum experimental parameters were determined as Ti/Si/C_gc having the molar ratio of 3/2.2/2, first holding at 1480°C for 30 min, and subsequent dwelling at 1300°C for 60 min.     

Low-Temperature Processing and Mechanical Properties of Zirconia and Zirconia–Alumina Nanoceramics

The 1.5- to 3-mol%-Y₂O₃-stabilized tetragonal ZrO₂ (Y-TZP) and Al₂O₃/Y-TZP nanocomposite ceramics with 1 to 5 wt% of alumina were produced by a colloidal technique and low-temperature sintering. The influence of the ceramic processing conditions, resulting density, microstructure, and the alumina content on the hardness and toughness were determined. The densification of the zirconia (Y-TZP) ceramic at low temperatures was possible only when a highly uniform packing of the nanoaggregates was achieved in the green compacts. The bulk nanostructured 3-mol%-yttria-stabilized zirconia ceramic with an average grain size of 112 nm was shown to reach a hardness of 12.2 GPa and a fracture toughness of 9.3 MPa·m^1/2. The addition of alumina allowed the sintering process to be intensified. A nanograined bulk alumina/zirconia composite ceramic with an average grain size of 94 nm was obtained, and the hardness increased to 16.2 GPa. Nanograined tetragonal zirconia ceramics with a reduced yttria-stabilizer content were shown to reach fracture toughnesses between 12.6–14.8 MPa·m^1/2 (2Y-TZP) and 11.9–13.9 MPa·m^1/2 (1.5Y-TZP).     

Preparation of regioisomers of structured TAG consisting of one mole of CLA and two moles of caprylic acid

TAG (MLM) with medium-chain FA (MCFA) at the 1,3-positions and long-chain FA (LCFA) at the 2-position, and TAG (LMM) with LCFA at the 1(3)-position and MCFA at 2,3(1)-positions are a pair of TAG regioisomers. Large-scale preparation of the two TAG regioisomers was attempted. A commercially available FFA mixture (FFA-CLA) containing 9-cis, 11-trans (9c, 11t)- and 10t,12c-CLA was selected as LCFA, and caprylic acid (C₈FA) was selected as MCFA. The MLM isomer was synthesized by acidolysis of acyglycerols (AG) containing two CLA isomers with C₈FA: A mixture of AG-CLA/C₈ FA (1∶10, mol/mol) and 4 wt% immobilized Rhizomucor miehei lipase was agitated at 30°C for 72 h. The ratio of MLM to total AG was 51.1 wt%. Meanwhile, LMM isomer was synthesized by acidolysis of tricaprylin with FFA-CLA: A mixture of tricaprylin/FFA-CLA (1∶2, mol/mol) and 4 wt% immobilized R. miehei lipase was agitated at 30°C for 24 h. The ratio of LMM to total AG was 51.8 wt%. MLM and LMM were purified from 1,968 and 813 g reaction mixtures by stepwise short-path distillation, respectively. Consequently, MLM was purified to 92.3% with 49.1% recovery, and LMM was purified to 93.2% with 52.3% recovery. Regiospecific analyses of MLM and LMM indicated that the 2-positions of MLM and LMM were 95.1 mol% LCFA and 98.3 mol% C₈ FA, respectively. The results showed that a process comprising lipase reaction and short-path distillation is effective for large-scale preparation of high-purity regiospecific TAG isomers.     

Effect of steric hindrance on hydrogen‐bonding interaction between polyesters and natural polyphenol catechin

The phase behaviors for the blends of poly(3‐hydroxypropionate) (PHP), poly(L ‐lactide) (PLLA), poly(D ‐lactide) (PDLA), and poly(D,L ‐lactide) (PDLLA) with catechin were investigated by differential scanning calorimetry. In PLLA/catechin, PDLA/catechin, and PDLLA/catechin blends, two glass transitions were detected when the catechin content was ≥40 wt %, whereas in PHP/catechin blends only one glass transition was observed over the whole range of blend compositions. The former and the latter results should reflect the inhomogeneous and the homogeneous nature of the blends, respectively, in the amorphous phase. These different phase behaviors should arise from the differences in the chemical structures between PHP and PLLA/PDLA/PDLLA, which dominates the strength and the number of intermolecular hydrogen‐bonding interactions between the ester carbonyl groups of polyesters and the phenol groups of catechin. As detected by FTIR spectroscopy, in comparison with PHP, the steric hindrance of side‐chain methyl groups of PLLA, PDLA, and PDLLA might restrain the formation of hydrogen bonds between their ester carbonyl groups and the phenol hydroxyl groups of catechin, even weakening the strength of such hydrogen bonds. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 3565–3573, 2004