Optical CO2 sensor with the combination of colorimetric change of α-naphtholphthalein and internal reference fluorescent porphyrin dye

A new optical CO₂ sensor based on the overlay of the CO₂ induced absorbance change of pH indicator dye α-naphtholphthalein with the fluorescence of tetraphenylporphyrin (TPP) was developed. The observed luminescence intensity from TPP at 655 nm increased with increasing the CO₂ concentration. The ratio I₁₀₀/I₀ values of the sensing films consisting of α-naphtholphthalein in ethyl cellulose layer and TPP in polystyrene layer, where I₀ and I₁₀₀ represent the detected luminescence intensities from a layer exposed to 100% nitrogen and 100% CO₂, respectively, that the sensitivity of the sensor, are more than 53.9. The response and recovery times of the sensing films consisting of α-naphtholphthalein in ethyl cellulose layer and TPP in polystyrene layer were less than 5 s for switching from nitrogen to CO₂, and for switching from CO₂ to nitrogen. The signal changes were fully reversible and no hysterisis was observed during the measurements. The highly sensitive optical CO₂ sensor based on fluorescence intensity changes of TPP due to the absorption change of α-naphtholphthalein with CO₂ was achieved.     

Microstructure evolution during thermomechanical processing in 3Mn-0.1C medium-Mn steel

ABSTRACT

Medium-Mn steels are energetically investigated as a candidate of the third generation advanced high strength steels (AHSSs). However, their phase transformation and microstructaure evolution during various heat treatments and thermomechanical processing are still unclear. The present study first confirmed the kinetics of static phase transformation behaviour in a 3Mn-0.1C medium-Mn steel. Hot compression tests were also carried out to investigate the influence of high-temperature deformation of austenite on subsequent microstructure evolution. It was found that static ferrite transformation was quite slow in this steel, but ferrite transformation was greatly accelerated by the hot deformation in austenite and ferrite two-phase regions. Characteristic dual-phase microstructures composed of martensite and fine-grained ferrite were obtained, which exhibited superior mechanical properties.

This paper is part of a Thematic Issue on Medium Manganese Steels.     

Development of a simple method for fabrication of transparent conductive films with high mechanical strength

We have developed a simple method of fabricating transparent conductive films with a high mechanical strength on glass and indium tin oxide substrates. It does not require a large excess of organic solvents and polymerization catalysts and can yield smooth films by spin-coating of a mixture of a commercially available aqueous dispersion of poly(3,4-ethylenedioxythiophene)-poly(4-styrene sulfonate) and a neat liquid of tetraethyl orthosilicate. Preparation conditions such as feed ratio, kinds of additives, and annealing temperature and time were optimized to give highly conductive, transparent and mechanically strong films.     

Character animation creation using hand-drawn sketches

To create a character animation, a 3D character model is often needed. However, since humanlike characters are not rigid bodies, to deform the character model to fit each animation frame is tedious work. Therefore, we propose an easy-to-use method for creating a set of consistent 3D character models from some hand-drawn sketches while keeping the projected silhouettes and features of the created models consistent with the input sketches. Since the character models possess vertexwise correspondences, they can be used for frame-consistent texture mapping or for making character animations. In our system, the user only needs to annotate the correspondence of the features among the input-vector-based sketches; the remaining processes are all performed automatically.     

Detection and Quantitation of Left-to-Right Shunts from Radionuclide Angiocardiography Using the Homomorphic Deconvolution Technique

The homomorphic filtering method is described for the detection and quantitation of left-to-right shunts from radionuclide angiocardiography. First, the method is investigated theoreticatly and numerically using a realistic model with systemic recirculation. It is demonstrated that even in a noisy situation the shunt flow fraction can be relatively well estimated, if only the characteristics of the fiters used are suitable. Second, the method is applied to real data, i.e., the pulmonary time-activity curves from radionucUde anglocardiography. The presence or absence of a left-to-right shunt is determined using the ratio AT/MTT. The pulmonary-to-systemic flow ratios calculated from the areas of the two decomposed curves are compared with those from oximetry at cardiac catheterization. Good agreement between the Qp/Qs ratios calculated by oximetry and radionucUide angiocardiography is obtained.     

Association of Ligamentum Flavum Hypertrophy with Adolescent Idiopathic Scoliosis Progression—Comparative Microarray Gene Expression Analysis

The role of the ligamentum flavum (LF) in the pathogenesis of adolescent idiopathic scoliosis (AIS) is not well understood. Using magnetic resonance imaging (MRI), we investigated the degrees of LF hypertrophy in 18 patients without scoliosis and on the convex and concave sides of the apex of the curvature in 22 patients with AIS. Next, gene expression was compared among neutral vertebral LF and LF on the convex and concave sides of the apex of the curvature in patients with AIS. Histological and microarray analyses of the LF were compared among neutral vertebrae (control) and the LF on the apex of the curvatures. The mean area of LF in the without scoliosis, apical concave, and convex with scoliosis groups was 10.5, 13.5, and 20.3 mm², respectively. There were significant differences among the three groups (p < 0.05). Histological analysis showed that the ratio of fibers (Collagen/Elastic) was significantly increased on the convex side compared to the concave side (p < 0.05). Microarray analysis showed that ERC2 and MAFB showed significantly increased gene expression on the convex side compared with those of the concave side and the neutral vertebral LF cells. These genes were significantly associated with increased expression of collagen by LF cells (p < 0.05). LF hypertrophy was identified in scoliosis patients, and the convex side was significantly more hypertrophic than that of the concave side. ERC2 and MAFB genes were associated with LF hypertrophy in patients with AIS. These phenomena are likely to be associated with the progression of scoliosis.     

Speed control of general‐purpose engine with electronic governor

This paper presents a general‐purpose engine speed control system with an electronic governor in order to improve the current system with a mechanical governor, which shows unstable characteristics as a result of a change in mechanical friction or the A/F ratio (air–fuel ratio). The control system above has the problems that the feedback signal is only the crank angle because of cost, and the controlled object is a general‐purpose engine, which is strongly nonlinear. In order to overcome these problems, a system model is presented for dynamic estimation of the amount of air flow, and a robust controller is designed. In concrete terms, the proposed system includes a robust sliding‐mode controller using the feedback signal of only the crank angle, with a genetic algorithm applied to the controller design. Simulations and experiments performed using Matlab/Simulink show the effectiveness of our proposal. © 2012 Wiley Periodicals, Inc. Electr Eng Jpn, 179(2): 64–71, 2012; Published online in Wiley Online Library ( wileyonlinelibrary.com ). DOI 10.1002/eej.21130