Asymmetric Regulation System Fit for Chinese Telecom Market

After the new round of restructuring of Chinese telecom sector,it's pressing to formulate and implement asymmetric regulation policies so as to shape an effectively competitive market structure in a relatively short term.This paper reviewed the asymmetric regulation policies and practices carried out in foreign telecom market,and then according to the specific situations of Chinese telecom market,proposed the principles and corresponding policies for establishing an asymmetric regulation system fit for Chin...     

固定化微生物脱除工业酸性废气中H_2S的研究

以H 2软性填料作为氧化亚铁硫杆菌的固定化载体 ,构成了固定床生物反应器。在一定操作条件下 ,考察了固定床生物反应器对Fe2 +的氧化速率 ,最大可达 7.6 7g/ (L·h)。并对固定床生物反应器运行中在载体表面形成的络合物进行了研究 ,X射线衍射证明此络合物为黄钾铁矾 [KFe3(SO4 ) 2 (OH) 6]。     

沸石孔结构对1-己烯异构化性能的影响

采用1-己烯为原料,对硅铝比相近、不同孔结构的沸石在脉冲微反装置上进行了评价试验,考察了FCC条件下沸石孔结构对烯烃异构化性能的影响。结果表明,大孔径的Y型沸石具有良好的异构化性能,异构化能力由强到弱的排列顺序为Y>β>ZRP>丝光沸石>镁碱沸石。     

A remark on inseparability of min-max systems

Min-max systems, or min-max-plus systems are algebraic models of discrete-event dynamic systems. They are nonlinear extensions of the well known linear max-plus system models. The structural property "inseparability" of min-max systems was proposed by us in a recent paper. It turns out that inseparability is equivalent to the property of "irreducibility" proposed recently by van der Woude and Subiono, although the two properties appear in very different forms. We will prove this fact here.     

CDMA发射分集系统的多用户检测常模算法分析

空时分集技术的最大优点在于在不增加带宽的情况下可以提高系统的可靠性,是目前移动通信的研究热点.常模算法是一种性能优良的码分多址(CDMA)盲多用户检测技术,能确保判决信号与实际传送信号之间的差错较小,误码率性能良好.文中提出将标准线性受限常模算法(LCCMA)与空时分组码(STBC)相结合,设计出一种收敛快、能够改善系统性能的基于2-空时分组码的多用户接收机.     

Fatigue Behavior and Retrofit Investigation of Distortion-Induced Web Gap Cracking

This paper studies a Kansas Department of Transportation welded plate girder bridge that developed fatigue cracks at small web gaps close to the girder top flange. Repair had been previously performed by softening the connection plate end with a slot retrofit, but cracks were recently found to have reinitiated at some of the repaired details and are again propagating. A comprehensive finite-element method study was performed to investigate the cracking behavior observed in the bridge and to recommend appropriate measures for future bridge retrofit. The analytical results show that stresses developed at the top flange web gaps could exceed yielding under the loading of an HS15 fatigue truck. The current slot repair used in the bridge was found to have introduced higher magnitude fatigue stresses in the web gap. To achieve a permanent repair of the bridge, it is recommended that a welded connection plate to flange attachment be used during future bridge retrofit. The web gap details should be able to withstand unlimited number of load cycles once this additional repair is performed.     

逆向反射镜光度测量

为了正确评价逆向反射镜的加工质量与使用效果，且将二者有机地统一起来，本文提出应根据测试目的来选择合适的光度测量方法，并进一步分析了不同测试目的将导致测量装置的组成、几何条件（距离，孔径角，工作姿态等）、光度条件（光源色温、稳定性与均匀性，接收器线性、灵敏度与光谱修正等）、测量参数（反光强度系数、逆反射系数、逆亮度系数等）等各不相同。