基于AutoCAD的折边肘板参数化实体造型的设计与实现

肘板是钢结构中常用的连接构件,折边肘板经常用于船舶主构件的折边对接中。为了提高折边肘板建模的效率,设计了折边肘板参数化三维实体造型过程;根据造型过程,探讨了肘板轮廓参数化生成及折边信息存储方法;给出了坐标转换及折边旋转算法;研究了面向对象的程序设计方法;以AutoCAD为开发平台,VS.Net为编程环境,ObjectARX为开发工具,实现了面向对象的折边肘板参数化实体造型。     

基于FPGA的MEMS陀螺仪SAR150实时数据采集系统设计

针对传统MEMS陀螺仪输出信息为模拟量且易受干扰、噪声较大的问题,结合SAR150陀螺仪可以直接输出数字信号的特点,提出了一种新型的数字陀螺仪实时数据采集系统;该系统以FPGA为主控制器,通过SPI接口完成对MEMS陀螺仪SAR150的控制与数据的传输,实现了对陀螺仪输出信号的采集、实时传输及存储;通过将所研制的数据采集系统应用于SAR150陀螺仪测量角速率实验,并对测得数据进行误差分析,实验结果表明:数据采集系统采集输出的角速率值与理论值的绝对误差标准差均小于0.2°/s;且该系统的可靠性高、实时性好,为后续的陀螺仪测试及标定奠定了基础,有一定的工程应用价值。     

TiO2/MOFs的制备及污染物降解现状

TiO2是较为成熟的半导体光催化材料,但因TiO2分散性差、量子利用率低、比表面积小、难回收等问题难以工业化.多孔金属有机框架(MOFs)的引入可增强TiO2/MOFs复合材料的光吸收性能,提高电子-空穴对分离效率和提高回收率.基于TiO2/MOFs制备时前驱体添加顺序不同,综述了TiO2/MOFs的3种制备方法(即Ship-in-a-bottle法、Bottle-around-ship法、One-pot法)及TiO2/MOFs光催化机理与性能影响因素,并探讨不同MOFs与TiO2结合的作用机理.最后,对TiO2/MOFs存在的问题提出建议.     

热处理工艺对BT9合金疲劳和高温持久性能的影响

本文研究了不同的热处理工艺对BT9钛合金的疲劳寿命和高温持久强度的影响,并对其组织、断口进行了光学和电子金相分析。指出了获得良好的综合机械性能的热处理工艺,并讨论了在不同区域内疲劳裂纹扩展的方式。     

Effect of ultrasonic power and bonding force on the bonding strength of copper ball bonds

Copper wire, serving as a cost-saving alternative to gold wire, has been used in many high-end thermosonic ball bonding applications. In this paper, the bond shear force, bond shear strength, and the ball bond diameter are adopted to evaluate the bonding quality. It is concluded that the ef/~cient ultrasonic power is needed to soften the ball to form the copper bonds with high bonding strength. However, excessive ultrasonic power would serve as a fatigue loading to weaken the bonding. Excessive or less bonding force would cause cratering in the silicon.     

Synthesis of LaF3 superfine powder by microwave heating method

LaF3 superfine powder was synthesized from La(CH3COO)3 and NH4 F by microwave heating method,using ethanol or pure water as dispersants respectively. The results of XRD and SEM indicate that the superfine powder has high purity, regular particle shape and narrow distribution of granularity. The granularity of the best sample is in the range of 100 -200 nm. The influence of different dispersants on the crystal degree and microstructure was discussed. After the superfine powder was formed into a slice at pressure of 25 - 60 MPa, its electrochemical impedance spectroscopy was tested by electrochemical impedance spectroscopy (EIS) measurement. The result shows that the grain refining of LaF3 powder increases its ionic conductivity. Compared with traditional preparation methods of LaF3 powder, the advantages of microwave heating method were summarized.     

34CrNiMo钢齿轮轴开裂原因分析

对34CrNiMo钢齿轮轴的化学成分、金相组织及断口分析表明，其淬火开裂的主要原因是由于锻造温度过高，导致过热缺陷所致。     

肥皂冒霜的成因探讨

本文讨论了肥皂冒白霜的主要原因,即肥皂中无机盐含量和油脂皂化后的有机酸败。生产实践证明,皂基含NaOH≤0．3%,NaCl≤0.2%,SiO2≥3%为宜;有机酸中含低分子酸和不饱和酸,必须控制油脂的酸价和严格控制工艺操作。     

泸天化厂辅锅炉水试行pH—磷酸盐协调处理已见成效

对于汽包式蒸汽锅炉,传统的炉内磷酸盐校正处理是用磷酸三钠调节炉水的离子比,达到防止钙镁水垢的目的。后来在高参数锅炉中实行的所谓“纯磷酸盐规范”是在加入的磷酸盐中含有酸式磷酸盐,力图使炉水的酚酞碱度全是由Na_3PO_4水解产生的,这样在炉水中就不会生成游离的NaOH,从而在防垢的同时又可防止碱性腐蚀。后来研究发现,即使炉水中的磷酸盐组成恰好相当于Na_3PO_4溶液,也避免不了游离NaOH的产生,尤其是在现代锅炉的热强度很高,容易在