Hydrogen annealing effect on DC and low-frequency noise characteristics in CMOS FinFETs

The hydrogen annealing process has been used to improve surface roughness of the Si-fin in CMOS FinFETs for the first time. Hydrogen annealing was performed after Si-fin etch and before gate oxidation. As a result, increased saturation current with a lowered threshold voltage and a decreased low-frequency noise level over the entire range of drain current have been attained. The low-frequency noise characteristics indicate that the oxide trap density is reduced by a factor of 3 due to annealing. These results suggest that hydrogen annealing is very effective for improving device performance and for attaining a high-quality surface of the etched Si-fin.     

Simulating strength and failure in engineering plant

Current features are considered in the calculation of carrying capacities for constructions in engineering plant (EP). Methods and algorithms are described for EP calculations with comprehensive incorporation of the effects from technological and working defects on the behavior of structures under standard and emergency conditions. __________ Translated from Khimicheskoe i Neftegazovoe Mashinostroenie, No. 8, pp. 38–40, August, 2006.     

Narrow-band correction of the residual amplitude modulation in frequency-modulation spectroscopy

We have developed a narrow-band controller in the MHz range, based on a field-programmable gate array. It is used to control the probe beam intensity in frequency-modulated spectroscopy experiments with an acoustooptic modulator. The residual amplitude modulation at the modulation frequency (2.5 MHz) is reduced by 50 dB. The first-harmonic detection of the signals is operated in saturation spectroscopy of I/sub 2/ at 514.5 nm and 501.7 nm. A reduction of the background noise and a large increase in the signal-to-noise ratio are obtained.     

Spinel Phase Relations in the Fe3O4–CuFe2O4 System

Phase equilibria involving spinel solid solutions, delafossite, and hematite in the Fe–Cu–O system are studied by emf measurements in solid-electrolyte galvanic cells. The results demonstrate that, above 1250 K, Fe₃O₄ and CuFe₂O₄ form a continuous series of solid solutions. At lower temperatures, the solid solution disproportionates with the formation of delafossite and Fe₂O₃, and two spinel solid solutions appear: one based on Fe₃O₄ and the other based on Cu₂FeO₄. The compositions of the spinel phases in equilibrium with delafossite and Fe₂O₃ are determined in the range 1100–1250 K.     

Analysis of feedback for higher order polarization-mode dispersion mitigation of NRZ 40-Gb/s optical transmission

First-order polarization-mode dispersion (PMD) compensation by means of a polarization controller and a differential delay line is not sufficient to guarantee error-free transmission for 40-Gb/s channels when higher order effects severely increase signal distortion. Higher order mitigation is possible by cascading more than one first-order block. However, only two-stage or three-stage devices remain simple enough to be actually controlled. The performance of such higher order PMD compensators is evaluated by means of numerical simulations. Two different feedback signals have been used, demonstrating that first-order and higher order PMD distortion of nonreturn-to-zero (NRZ) pulses at 40 Gb/s can be strongly mitigated for instantaneous values of the differential group delay (DGD) up to the bit slot, when the compensator is properly controlled.     

Metastable phase relation and phase equilibria in the Cr2O3-Fe2O3 system

In order to ascertain the metastable phase relation in the Cr₂O₃-Fe₂O₃ system, the existing phases were investigated by X-ray analysis using samples obtained by heating the coprecipitated powders for 1 h at 600–1000°C. There was a metastable two-phase region of Cr₂O₃-rich (CC) and Fe₂O₃-rich (FC) phases below about 940°C. Equilibrium state of 1:1 composition at 600–900°C was considered to be a single phase of the corundum solid solution. The metastable two-phase CC + FC region was suggested to appear probably due to the compositional inhomogeneity in the coprecipitated powders.     

Management gaps analysis: a case study of groundwater resource management in New Zealand

The primary objective of this project is to identify gaps, whether real or perceived, that hinder effective groundwater management in New Zealand. These gaps show as gaps in information, gaps in implementation, gaps in technological and management tools, and gaps in understanding of fundamental processes. The secondary objective is to propose a management strategy to close the identified gaps. Several methods are used to meet these objectives: surveys distributed to selected staff in each regional council; the review of various written reports; the analysis of land-use databases; and private consultation within each regional council. Results show that groundwater management in New Zealand is generally reactionary with the main gaps being in strategic planning and national guidelines. Most gaps appear to be predominantly information and implementation issues. In some cases there are gaps in the understanding of fundamental processes within an aquifer system, including the long-term effects of land-use on groundwater quality. An adaptive management approach is suggested as a means of closing these gaps.