Production of compounded asphalts of improved quality

Paving-and roofing-grade asphalts were obtained at LUKOIL-Permnefteorgsintez Ltd. by mixing peroxidized asphalt and a number of high-boiling unoxidized petroleum products in certain ratios. The asphalts obtained have improved performance characteristics: high plasticity and low brittleness temperature. __________ Translated from Khimiya i Tekhnologiya Topliv i Masel, No. 2, pp. 26–28, May–June, 2006.     

CYLINDRICAL AND CONICAL FOLD GEOMETRIES IN THE CANTARELL STRUCTURE, SOUTHERN GULF OF MEXICO: IMPLICATIONS FOR HYDROCARBON EXPLORATION

The NW‐SE trending Cantarell structure in the Gulf of Campeche hosts the largest oilfield in Mexico. The oil occurs predominantly in latest Cretaceous – earliest Tertiary breccias with subsidiary reserves in Upper Jurassic (Oxfordian and Kimmeridgian) and Lower Cretaceous oolitic and partially dolomitized limestones, dolomites and shaly limestones. Cantarell has been interpreted both as a fold‐and‐thrust zone and as a dextral transpressional structure. Analysis of structure contours at 100m intervals, on the tops of the Tertiary breccia and the Kimmeridgian (Upper Jurassic) dolomite, indicates that the structure is an upright cylindrical fold with gently plunging conical terminations; there is also a conical portion in the central part of the structure. The axes of the central, NW and SE cones are subvertical. This geometry indicates that the two fold terminations and the central cone are aprons rather than points, with the NW and central cone axes intersecting the cylindrical fold axis at the point where the geometry switches from conical to cylindrical. The apical angle (i.e. the angle between the fold and cone axes) varies as follows: (i) in the NW cone, it is ～70° in the breccia and ～76° in the Kimmeridgian dolomite; (ii) in the central cone, it is ～77° in the breccia and ～73° in the Kimmeridgian dolomite; and (iii) in the SE cone, it is ～64° in the breccia and ～57° in the Kimmeridgian dolomite. This indicates that whereas the fold opens with depth in the NW cone, it tightens with depth in the central and SE cones. Assuming a parallel fold geometry, these apical angles indicate an increase in volume in the NW cone (i.e. larger hydrocarbon reservoirs), compared to the central and SE cones. Theoretical considerations indicate that the curvature increases dramatically towards the point of the cone. In the case of the Cantarell structure, the apices of the cones are located at the conical‐cylindrical fold junctions, where the highest curvature may have resulted in a higher degree of fracturing. The coincidence of maximum curvature and the intersection of the conical and cylindrical fold axes in the fold culminations with porous and permeable reservoir rocks may have made these locations favourable for the accumulation of hydrocarbons.     

Adaptive viewpoints for co-browsing on heterogeneous devices

Co-browsing is an activity in which a group of users navigate their way through of a set of Web pages together for a shared purpose. Effective co-browsing among users with different device capabilities requires a shared understanding of those Web pages. This paper demonstrates the concept of shared viewpoints (SVPs), and personal viewpoints (PVPs), for co-browsing, before detailing a framework for implementing these concepts. Finally, the effectiveness of the framework is presented through a perceptual experiment.     

PETROLEUM MIGRATION, FAULTS AND OVERPRESSURE, PART I: CALIBRATING BASIN MODELLING USING PETROLEUM IN TRAPS — A REVIEW

This paper considers the principles of deciphering basin-scale hydrocarbon migration patterns using the geochemical information which is present in trapped petroleum. Petroleum accumulations in subsiding basins can be thought of as "data archives" within which stored information can help us to understand aspects of hydrocarbon formation and migration. This information can impart a time-resolved picture of hydrocarbon migration in a basin in response to processes associated with progressive burial, particularly in the context of the occurrence and periodic activity of faults.
This review, which includes a series of tentative models of migration-related processes in the extensional Halten Terrace area, offshore mid-Norway, illustrates how we can use information from the migrating mobile hydrocarbon phase to improve our knowledge of the static geological system. Of particular importance is the role of sub-seismic heterogeneities and faults in controlling migration processes. We focus on how the secondary migration process can be enhanced in a multi-source rock basin such as the Halten Terrace, thereby increasing prospectivity.     

Robust nonlinear feedback–feedforward control of a coupled kinetic Monte Carlo–finite difference simulation

Robust nonlinear feedforward–feedback controllers are designed for a multiscale system that dynamically couples kinetic Monte Carlo (KMC) and finite difference (FD) simulation codes. The coupled codes simulate the copper electrodeposition process for manufacturing on-chip copper interconnects in electronic devices. The control objective is to regulate the current density subject to the condition that the steady-state fluctuation of the overpotential remains bounded within ±0.01 V. The controller designs incorporate a low-order stochastic model that captures the input–output behavior of the coupled KMC–FD code. The controllers achieve the objectives and the closed-loop responses implemented on the low-order model and the coupled KMC–FD code match well within stochastic variations. The nonlinear feedforward control reduces the rise time of the controller response while the feedback control ensures robustness in the presence of model uncertainty.     

Development of a simple microsystems membrane probe card

Presented here are details of the development of a novel membrane integrated circuit (IC) probe card structure based on microsystems technology. The device design allows probing of both solder bumps and pads. A self-limiting sensor was integrated to prolong device lifetime. Comparison with and discussion of the use of modelling is made. Possible enhancements to the probing structure are discussed to improve alignment and measurements. Also shown is data using our microsystems probe card to access a simple IC device. Our device has a contact resistance of less than 0.5 Ω for a force of 0.004 N. A method to implement our probing structure for commercial application and the potential developments which can be made to improve its ease of use are then discussed.     

Vacuum degassing of chromium-nickel-molybdenum steel at the Magnitogorsk Metallurgical Combine

The Magnitogorsk Metallurgical Combine has conducted a study of the effect of technological factors on the hydrogen content of chromium-nickel-molybdenum steel after vacuum degassing. It was established that the most important factor is the hydrogen content of the steel before the degassing operation. The study also determined the effects of the circulation coefficient, the duration of the degassing operation, and the vacuum used in the treatment. __________ Translated from Metallurg, No. 7, pp. 68–69, July, 2006.     

Capture of Organic Vapors Using Adsorption and Electrothermal Regeneration

Activated-carbon-fiber cloth (ACFC) is an alternative adsorbent to granular activated carbon (GAC) for removing and recovering organic vapors from gas streams. Electrothermal desorption (ED) of ACFC provides rapid regeneration while requiring less energy compared to traditional regeneration techniques used with GAC. This paper provides proof-of-concept results from a bench-scale ACFC adsorption system. The automated system captured 1,000 ppmv of hazardous air pollutants/volatile organic compounds (HAPs/VOCs) from air streams and demonstrated the use of ED, using ac voltage, to recover the HAP/VOC as a pure liquid. The desorbed HAP/VOC condensed onto the inner walls of the adsorber and was collected at the bottom of the vessel, without the use of ancillary cooling. Seventy percent of the HAP/VOC was collected per cycle as condensate, with the balance being retained in the regenerated adsorber or recycled to the second adsorber. ED with in-vessel condensation results in minimal N2 consumption and short regeneration cycle times allowing the process to be cost competitive with conventional GAC-based adsorption processes. This technology extends the application of carbon adsorption systems to situations that were previously economically and physically impractical.     

Magnetic-field-controlled optical transmission in a system of metal diaphragms with apertures and a thin dielectric interlayer

A system comprising two metal diaphragms with holes and a thin dielectric interlayer exhibits magnetic-field-controlled optical transmission. This phenomenon can be used, in particular, for the creation of light modulators.     

In situ TEM observations of fracture in nanolaminated metallic thin films

Fracture of single crystal nanolaminated thin films has been investigated through in situ straining of cross-sectional samples of Cu/Ni nanolaminates grown on Cu (001) single crystal substrates. The earlest stages of deformation exhibits a confined layer slip mechanism. With continued straining, unstable fracture occurs creating a mixed-mode crack that propagates across the nanolaminate, roughly perpendicular to the interfaces. Eventually, stable crack growth with intense plastic deformation ahead of the crack tip occurs over many bilayers in the direction of crack growth. Simultaneously, plasticity was seen to spread only 1 or 2 bilayer distances normal to the crack, creating an extremely localized plastic zone. Transmission electron microscopic (TEM) examination after the test did not reveal the presence of dislocations in the crack wake, except where severe crack deflection was observed. By comparison, the plastic zone size in the substrate was greater by several of orders of magnitude.