First and second law analyses of a typical solar air dryer system: a case study

This communication presents an experimental study based on energy and exergy analyses of a typical solar air dryer. On the basis of the experimental results, the first and the second law efficiencies are calculated with respect to the available solar radiation. It is found that the second law efficiency is much less than the first law efficiency irrespective of the mass flow rate of the circulating fluid. It is also found that both efficiencies are an increasing function with respect to the mass flow rate of the working fluid. For a particular day, it is also found that first and second law efficiencies fluctuate according to radiation. The results obtained in this article are found to be consistent with those obtained by earlier authors as given in the literature.     

Secure Key Agreement with Rekeying Using FLSO Routing Protocol in Wireless Sensor Network

Wireless Personal Communications - A challenge in wireless sensor network (WSN) is to design an energy efficient and secure network protocol because sensors are the wireless device with limited...     

Mechanical and thermal properties of wood fibers reinforced poly(lactic acid)/thermoplasticized starch composites

Thermoplasticized starch (TPS) filled poly(lactic acid) (PLA) blends are usually found to have low mechanical properties due to poor properties of TPS and inadequate adhesion between the TPS and PLA. The purpose of this study was to investigate the reinforcing effect of wood fibers (WF) on the mechanical properties of TPS/PLA blends. In order to improve the compatibility of wood with TPS/PLA blends, maleic anhydride grafted PLA (MA‐g‐PLA) copolymer was synthesized and used. TPS, TPS/PLA blends, and WF reinforced TPS/PLA composites were prepared by twin‐screw extrusion and injection molded. Scanning electron microscope and crystallinity studies indicated thermoplasticity in starch. WF at two different weight proportions, that is, 20% and 40% with respect to TPS content were taken and MA‐g‐PLA at 10% to the total weight was chosen to study the effect on mechanical properties. At 20% WF and 10% MA‐g‐PLA, the tensile strength exhibited 86% improvement and flexural strength exhibited about 106% improvement over TPS/PLA blends. Increasing WF content to 40% further enhanced tensile strength by 128% and flexural strength by 180% with respect to TPS/PLA blends. Thermal behavior of blends and composites was analyzed using dynamic mechanical analysis and thermogravimetric analysis. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46118.     

Experimental,equilibrium modelling,and column design for the reactive separation of biomass-derived 2-furoic acid

Electrochemical conversion of biomass to value-added chemicals has gained impetus in recent years. Herein, we present a methodology for recovering biomass-derived 2-furoic acid from the dilute aqueous stream by reactive extraction. The reactive extraction was performed using a chemical extractant, trioctylamine (TOA), with diluents (octanol, chloroform, and diethyl ether). Equilibrium parameters influencing the recovery of 2-furoic acid were evaluated. Using TOA in various diluents, the 2-furoic acid was recovered with 85%–99% efficiency. A 1:1 complex of the 2-furoic acid—TOA was formed in the organic phase, and the experimental equilibrium complexation constant was compared with that obtained from the relative basicity and Langmuir models. The equilibrium parameters were used for column design to estimate the solvent to feed ratio (S/F) and the number of theoretical stages (NTS). The NTS required is 12 to attain 99% recovery of 2-furoic acid in counter-current extraction. The present study sheds light on the reactive extraction process adopted for process intensification with electrochemical conversion, paving the way for the commercialization of valuable products obtained from biomass.     

Performance of clay masonry prisms with light weight plaster exposed to standard fire exposure

Clay bricks are one of the most widely used materials in building construction due to their advantages, including local availability, ease of fabrication and cost-effectiveness. Fire is one of the dangerous hazards that can cause damage the life and property. Lightweight plasters play a vital role in insulating the masonry construction during fire accident. There is only limited data and information available on the fire performance of Clay Brick Masonry (CBM) insulated with lightweight plaster. An extensive investigation was undertaken to evaluate the residual strength properties and physical characteristics of CBM prisms exposed to elevated temperatures. CBM prisms plastered with M-sand mortar, vermiculite mortar, and perlite mortar were used for the investigation. Protected prisms were exposed to elevated temperatures following the ISO 834 standard fire curve for durations of 30 min (821°C), 60 min (925°C), 90 min (986°C), and 120 min (1029°C). Mechanical properties such as axial load carrying capacity, stress–strain behaviour, elastic modulus, and crack pattern were examined. The mechanical properties of CBM prisms were found to be highly influenced by the type of plastering, intensity, and the duration of heating. The microstructure and image analysis confirmed the effects of temperature exposure on protective plasters. Equations are proposed to determine the residual axial compressive strength and the elastic modulus of CBM. It was found that the specimens plastered with perlite mortar had better fire resistance.     

Transport of cobalt(II) through a hollow fiber supported liquid membrane containing di-(2-ethylhexyl) phosphoric acid (D2EHPA) as the carrier

This work presents experimental, modeling and simulation studies for Co²⁺ ion extraction using hollow fiber supported liquid membrane (HFSLM) operated in a recycling mode. Extractant di-(2-ethylhexyl) phosphoric acid (D2EHPA) diluted with kerosene has been used as the membrane phase. The Co²⁺ ion concentration in the aqueous feed phase was varied in the range of 1–3 mM. Also, D2EHPA concentration was varied in the range of 10–30% (v/v). A mass transfer model has been developed considering the complexation and de-complexation reactions to be fast and at equilibrium. Equations for extractant mass balance and counter-ion (H⁺) transport have also been incorporated in the model. Extraction equilibrium constant (K_ex) for cobalt–D2EHPA system has been estimated from equilibration experiments and found to be 3.48 × 10⁻⁶. It was observed that the model results are in good agreement with the experimental data when diffusivity of metal-complex (D_m) through the membrane phase is 1.5 × 10⁻¹⁰ m²/s. Feed phase pH and strip phase acidity had negligible effect on the extraction profiles of Co²⁺ ions. An increase in D2EHPA concentration increased extraction rates of Co²⁺ ions. The membrane phase diffusion step was found to be the controlling resistance to mass transfer.     

Aerosol Deposition in Sampling Probes

Deposition of aerosol particles on the inner walls of sampling probes is of concern in many aerosol sampling applications. Only inertial and gravitational effects have been considered in previous studies of the aerosol deposition; however, the lift force on particles is also of significance. In this investigation, experiments have been conducted to construct a database for aerosol deposition in Willeke-type sampling probes. An empirical correlation has been made between wall losses and the depositional forces of drag, gravity, inertia, and particle lift through the use of dimensionless parameters. Inclusion of the lift effect in this correlation not only helps to better predict particle behavior in the sampling inlet, but it also provides a basis for understanding of the intrinsic deposition phenomenon. The correlation has a geometric standard deviation of 1.13 and a 0.93 correlation coefficient relative to the experimental data.     

Development of Synthetic Ketonic Resin

In the present work, the self-polymerization reaction of cyclohexanone was studied to develop a synthetic resin. Synthetic resins are extensively used in paint industry to improve the adhesiveness of paints. Polymerization reactions were carried out in a high-pressure reactor. The results suggest that the self-polymerization of cyclohexanone mainly depends on alkali concentration, reaction temperature, and reaction time. As the ketone-to-alkali ratio decreases, the degree of polymerization increases, which leads to an increase in the hydroxyl value and softening point and a remarkable decrease in solubility. A good-quality solid resin could be obtained with a ketone-to-alkali ratio less than 5 in the temperature range between 130°C and 160°C and within the time duration of 12–22 h. These data may be useful to develop the desired quality of resin in the field of paint application.     

Review of Chemical Reactions in the NO Reduction by CO on Rhodium/Alumina Catalysts

The emissions of nitric oxide and carbon monoxide from internal combustion engines are of primary concern due to their impact on the environment and people's health. Since rhodium has proven to be an important catalyst for the reduction of nitric oxide by carbon monoxide, its accurate modeling is of significant value to industry. This paper reviews the literature with respect to this interaction in order to explain the history of the detailed reactions occurring on the surface. This review was accomplished in the absence of other species in order to focus the efforts and reduce the complexity of the task. In addition, this work presents an appropriate global reaction expression based on these detailed reactions for use in one-dimensional aftertreatment catalyst models.     

Synthesis,characterization and application of Azadirachta indica juss (neem oil) fatty amides (AIJFA) based polyurethanes coatings: A renewable novel approach

Number of diethanol amides has been developed by scientist using various vegetable oils and not from neem seed oil. Most of the research work on neem seed oil has explored its applications in pharmaceutical and pesticides fields. This paper representing new area of application of neem seed oil for polymeric resin, in which we attempted to synthesize the neem seed oil based poly(urethane fatty amides) by reaction of neem oil fatty amide (AIJFA) with trimer of isophorone diisocyanate (IPDI). Spectral study of AIJFA was carried out by using FT-IR and ¹H NMR techniques. Molecular weight of AIJFA was determined by gel permeation chromatography (GPC). Fatty acid composition of neem seed oil was obtained by gas chromatographic method. The coatings applied on mild steel plates were evaluated by determining coating properties, chemical and corrosion resistances. TGA study of coatings showed higher thermal stability to AIJFA based PU coatings compared to normal urethane and alkyd coatings.