Failures induced by electromigration in ECL 100k devices

Reliability of ECL 100k devices using Al (4%wt Cu, 1%wt Si) double level metallization, isoplanar technology with shallow, 0.25 μm, base-emitter junctions was evaluated by means of high current and high temperature stresses. Three failure modes connected with electromigration phenomena were found in the output transistor: (a) base-emitter shunts owing to junction spiking caused by Al-Si interdiffusion enhanced by electromigration; (b) collector-emitter shorts due to the breaking of the dielectric oxide between two superimposed metal levels owing to material transport and pile-up in the underlying metallization; (c) open circuit of the output emitter due to void growth in the Cu-depleted areas of the Al interconnections. After B-E shunts, failure mechanism evolves towards two different sequences of failure modes, according to the different transistor structures; in fact C-E shorts were found to occur only when collector and emitter metals are superimposed, while the open circuit of the output emitter is the final failure for all configurations. The earlier and more frequent failure mode observed is the resistive shunt of the base-emitter junction of the output transistor, in agreement with previously reported data on electromigration effects in Al (Cu, Si) metallizations used both as interconnections and as contacts to shallow junctions.     

Salmeterol compared with slow-release terbutaline in nocturnal asthma. A multicenter, randomized, double-blind, double-dummy, sequential clinical trial. French Multicenter Study Group

The aim of the multicenter, randomized, double-blind, double-dummy, parallel-group clinical trial with a 2-week treatment period was to compare the efficacy and safety of salmeterol (50 micrograms twice daily) with slow-release (SR) terbutaline (5 mg orally, twice daily) in nocturnal asthma. A total of 159 asthmatic adults (FEV, 50-90% of predicted value; sex ratio: 0.87) with at least two nocturnal awakenings during a 7-d run-in period was included in the study. Patients were centrally randomized with a national computer network (Minitel). The main variable (number of awakening-free nights during the last week of treatment) was analyzed according to a sequential method with the one-sided triangular test. The number of awakening-free nights (+/- SD) was significantly higher in the salmeterol group: 5.3 +/- 2.4 vs 4.6 +/- 2.3 (P = 0.006). Salmeterol was significantly more effective than SR-terbutaline in the following factors: number of patients without any awakening during the last week of treatment (50% vs 27%, P = 0.003), mean morning PEF (351 +/- 109 l/min-1 vs 332 +/- 105 l/min-1, P = 0.04), PEF diurnal variation 6 +/- 10% vs 11 +/- 12%, P = 0.01), overall assessment of efficacy by the patient and the investigator (P = 0.001 and 0.005, respectively), and daily rescue salbutamol intakes (P = 0.004). In the salmeterol group, significantly fewer patients reported adverse events (16% vs 29%, P = 0.04).(ABSTRACT TRUNCATED AT 250 WORDS)     

Tunable,Grating-Gated,Graphene-On-Polyimide Terahertz Modulators

An electrically switchable graphene terahertz (THz) modulator with a tunable-by-design optical bandwidth is presented and it is exploited to compensate the cavity dispersion of a quantum cascade laser (QCL). Electrostatic gating is achieved by a metal grating used as a gate electrode, with an HfO₂/AlO_x gate dielectric on top. This is patterned on a polyimide layer, which acts as a quarter wave resonance cavity, coupled with an Au reflector underneath. The authors achieve 90% modulation depth of the intensity, combined with a 20 kHz electrical bandwidth in the 1.9–2.7 THz range. The modulator is then integrated with a multimode THz QCL. By adjusting the modulator operational bandwidth, the authors demonstrate that the graphene modulator can partially compensate the QCL cavity dispersion, resulting in an integrated laser behaving as a stable frequency comb over 35% of the operational range, with 98 equidistant optical modes and a spectral coverage ~1.2 THz. This paves the way for applications in the terahertz, such as tunable transformation-optics devices, active photonic components, adaptive and quantum optics, and metrological tools for spectroscopy at THz frequencies.     

Effect of water/fuel emulsions and a cerium-based combustion improver additive on HD and LD diesel exhaust emissions

One of the major technological challenges for the transport sector is to cut emissions of particulate matter (PM) and nitrogen oxides (NOx) simultaneously from diesel vehicles to meet future emission standards and to reduce their contribution to the pollution of ambient air. Installation of particle filters in all existing diesel vehicles (for new vehicles, the feasibility is proven) is an efficient but expensive and complicated solution; thus other short-term alternatives have been proposed. It is well known that water/diesel (W/ D) emulsions with up to 20% water can reduce PM and NOx emissions in heavy-duty (HD) engines. The amount of water that can be used in emulsions for the technically more susceptible light-duty (LD) vehicles is much lower, due to risks of impairing engine performance and durability. The present study investigates the potential emission reductions of an experimental 6% W/D emulsion with EURO-3 LD diesel vehicles in comparison to a commercial 12% W/D emulsion with a EURO-3 HD engine and to a Cerium-based combustion improver additive. For PM, the emulsions reduced the emissions with -32% for LD vehicles (mass/km) and -59% for the HD engine (mass/ kWh). However, NOx emissions remained unchanged, and emissions of other pollutants were actually increased forthe LD vehicles with +26% for hydrocarbons (HC), +18% for CO, and +25% for PM-associated benzo[a]pyrene toxicity equivalents (TEQ). In contrast, CO (-32%), TEQ (-14%), and NOx (-6%) were reduced by the emulsion for the HD engine, and only hydrocarbons were slightly increased (+16%). Whereas the Cerium-based additive was inefficient in the HD engine for all emissions except for TEQ (-39%), it markedly reduced all emissions for the LD vehicles (PM -13%, CO -18%, HC -26%, TEQ -25%) except for NOx, which remained unchanged. The presented data indicate a strong potential for reductions in PM emissions from current diesel engines by optimizing the fuel composition.     

Reliability evaluation of plastic packaged devices for long life applications by THB test

The reliability of transistors, bipolar and CMOS integrated circuits encapsulated in different types of plastic packages was investigated by using the 85°C/85% R.H. test with applied bias and the results compared with a long term operating life test. Particular attention was devoted to pointing out the influence of technology, process control and working conditions on device reliability and failure mechanisms.In micropackaged transistors the importance of surface passivation in protecting the devices against gold corrosion was forcused, while the need of good process control was confirmed by the results of the test on micropackaged linear integrated circuits.In dual-in-line CMOS integrated circuits silicon nitride and polymide give, in general, a superior protection, but good results were obtained also with normal P-glass passivation when a clever arrangement of layout design rules was adopted. Results obtained exhibit a significant improvement in the reliability of plastic packaged devices, with the best figures showing no failures after 15,000 hours at 85°C/85% R.H. test with bias.     

A cooperative approach for topology control in Wireless Sensor Networks

The choice of the transmission power levels adopted in Wireless Sensor Networks (WSNs) is critical to determine the performance of the network itself in terms of energy efficiency, connectivity and spatial reuse, since it has direct impact on the physical network topology.In this paper, a cooperative, lightweight and fully distributed approach is introduced to adaptively tune the transmission power of sensors in order to match local connectivity constraints. To accurately evaluate the topology control solution, a small-scale testbed based on MicaZ sensor nodes is deployed in indoor and outdoor scenarios. Practical measures on local and multi-hop connectivity, convergence time and emitted power are used to compare the proposed approach against previous solutions. Moreover, mathematical programming formulations of the topology (power) control problem are introduced to assess the optimality of the distributed algorithm. Finally, simulation analysis complements the experimental evaluation in large-scale static and mobile WSN scenarios, where a testbed implementation becomes unfeasible.     

Alterations of the glucose metabolism in a triose phosphate isomerase-negative Saccharomyces cerevisiae mutant

The absence of triose phosphate isomerase activity causes an accumulation of only one of the two trioses, dihydroxyacetone phosphate, and this produces a shift in the final product of glucose catabolism from ethanol to glycerol (Compagno et al., 1996). Alterations of glucose metabolism imposed by the deletion of the TPI1 gene in Saccharomyces cerevisiae were studied in batch and continuous cultures. The Deltatpi1 null mutant was unable to grow on glucose as the sole carbon source. The addition of ethanol or acetate in media containing glucose, but also raffinose or galactose, relieved this effect in batch cultivation, suggesting that the Crabtree effect is not the primary cause for the mutant's impaired growth on glucose. The addition of an energy source like formic acid restored glucose utilization, suggesting that a NADH/energy shortage in the Deltatpi1 mutant could be a cause of the impaired growth on glucose. The amount of glycerol production in the Deltatpi1 mutant could represent a good indicator of the fraction of carbon source channelled through glycolysis. Data obtained in continuous cultures on mixed substrates indicated that different contributions of glycolysis and gluconeogenesis, as well as of the HMP pathway, to glucose utilization by the Deltatpi1 mutant may occur in relation to the fraction of ethanol present in the media.     

Superswelling Microneedle Arrays for Dermal Interstitial Fluid (Prote)Omics

The noninvasive sampling of dermal interstitial fluid (ISF) for the monitoring of clinical biomarkers is a greatly appealing area of research. The identification of molecular biomarkers in biological fluids has been accelerated with -omics analyses but remains limited in ISF because of its time-consuming and complex extraction process. Here, the generation of microneedle (MN) patches made of superabsorbent acrylate-based hydrogels for the rapid sampling of dermal ISF is described to explore its proteome. In depth, iterative optimization allows the identification of novel acrylate-based compositions with the required chemical, mechanical, and biocompatibility properties allowing proteomic analysis of the extracted ISF for the first time after sampling with swelling MNs. The generated MN arrays show no cytotoxic effect, successfully cross the stratum corneum, and can collect up to 6 µL of dermal ISF in 10 min in vivo. Proteomics lead to the detection of 176 clinically relevant biomarkers in the collected samples validating the use of ISF as a relevant bodily fluid for disease monitoring and diagnostic. Importantly, it is discovered that extraction fingerprint is strongly dependent on the MNs chemistry, and thus specific biomarkers could be selectively extracted by tuning the composition of the patch, making the system versatile and specific.